RF Bandpass Filter 學生：陳昱夫 E-mail ： ksu.chenyufu@gmail.com

1. RF Bandpass Filter 學生：陳昱夫 E-mail：ksu.chenyufu@gmail.com

2. Ultra-Wideband (UWB) Bandpass FilterWith Embedded Band Notch Structures(1) Proposed UWB BPF with embedded band notch stubs. Predicted and the measured results for Filter-A with the FCC indoor mask.

3. Ultra-Wideband (UWB) Bandpass FilterWith Embedded Band Notch Structures(2) Insertion loss of the embedded stub with varying gap for Ws =0.1mmand Wc = 1.3 mm. Schematic diagrams of (a) conventional open-circuited stub, (b) spurline,and (c) proposed embedded open-circuited stub. Full-wave EM simulation of the complete layout of the designed UWBBPF with varying equal stub lengths.

4. Ultra-Wideband (UWB) Bandpass FilterWith Embedded Band Notch Structures(3) • 製作於FR4板、介電常數為 3.05 基板高度0.508 損失0.025 • 不具有傳輸零點 • 具有一個可調式notchedband • 結構尺寸22.2mmX15.1mm，大約為1.07λgX0.54λg。 • 中心頻率在5.83GHz

5. IE3D模擬

6. Investigation in Open Circuited Metal LinesEmbedded in Defected Ground Structureand Its Applications to UWB Filters(1) Schematic diagrams of (a) top view of proposed UWB BPF, (b) bottomview of proposed UWB BPF, (c) top view of proposed UWB BPF with notchbandimplementation, (d) bottom view of proposed UWB BPF with notch bandimplementation Simulated and measured results of Fabricated UWB BPF.

7. Investigation in Open Circuited Metal LinesEmbedded in Defected Ground Structureand Its Applications to UWB Filters(2) • 製作於FR4板、介電常數為4.4、基板高度0.8、損失為0.025。 • 具有兩個傳輸零點，分別在1.65GHz和11.36GHz。 • 具有一個notchedband 。(只可控制頻寬) • 結構尺寸11.7mmX6.3mm、大約為0.41λgX0.22λg。 • 中心頻率為 5.5GHz

8. IE3D模擬

9. Ultra Wideband Bandpass Filter with Dual Notch Bands(1) Simulated and measured frequency responses and (b) group delay of the fabricated UWB BPF. The dimensions are W1 =0.1, W 2 = 0.7, W 3 = W 5 = 1.8, W 4 = 0.7, Lc = 4, L1 = 4.4, L2 = L4 =2, L3 = 3.3, L5 = 4.2, d = 4.2, S1 = 0.1, S2 = S3 = 0.2. All are in mm. Structure of the proposed UWB filter

10. Ultra Wideband Bandpass Filter with Dual Notch Bands(2) (a) Structure of the square etched MMR and (b) |S21|-magnitude of the MMR with different coupled line lengths (Lc). |S21|-magnitude

11. Ultra Wideband Bandpass Filter with Dual Notch Bands(3) |S21|-magnitude in comparison of SIR 1 SIR 2 with tuning 1.

12. Ultra Wideband Bandpass Filter with Dual Notch Bands(4) • 製作於Duroid6010板、介電常數為10.2、基板高度為1.27、損失0.0023。 • 整個通帶從3.1GHz~11GHz。 • 不具有傳輸零點。 • 具有兩個可調式notchedband 。 • 結構尺寸為13.4mmX8.62mm。

13. IE3D模擬

14. Compact Ultra-Wideband Bandpass FilterUsing Dual-Line Coupling Structure(1) Simulated and measured results of the fabricated BPF with spurious response suppression. Topology of the compact UWB BPF

15. Compact Ultra-Wideband Bandpass FilterUsing Dual-Line Coupling Structure(3) • 超寬帶帶通 4.9和10.9GHz • 返回損失超過 15db從 5.7至10.7GHz • 在1分貝插入損耗約 5GHz帶寬，最小插入損耗為 0.49 dB的7.3GHz。 S-parameters and group delay of the UWB BPF.

16. IE3D模擬

17. A New Dual-Band MicrostripBandpassFilter Using Net-Type Resonators

18. INTRODUCTION λ/2 SIRs shown in Fig. 1(a-1) and (a-2) are employed to design dual-band filters with two passbandsat frequencies ƒ1 and ƒ2 (ƒ2 > ƒ1) . The frequency ratio ƒ2/ƒ1 determines which type of SIRs ( K <1 or K>1 ) should be adopted.

19. INTRODUCTION λ/4 SIR shown in Fig. 1(b-1) was evolved into the net-type resonator [9] depicted in Fig. 1(c-1) and (d-1), and then exploited to design a single passband filter.

20. INTRODUCTION the net-type resonator in the K>1 region shown in Fig. 2 is developed to achieve two closely specified resonant frequencies. The filter developed in this letter not only has two transmission zeros to improve the selectivity of each passband, but also provides a wide stopband suppression and an excellent mid-band rejection between two passbands. Fig. 2. Spurious resonant frequencies of the λ/4 stepped-impedance resonator With K=Z2/Z1 <1 and K=Z2/Z1 >1

21. DUAL-BAND NET-TYPE RESONATOR • To design the λ/4 SIR with two close resonant frequencies, ƒ1 and ƒ2 (ƒ2/ƒ1 ≈ 2). It is comprised of two transmission lines with the equal electrical length and the impedance ratio K=Z2/Z1 > 1. • The high impedance (Z2) line is kept open-circuited while the low impedance (Z1) line is connected to the ground. Hence, the first two resonant frequencies f1 and f2 (f2> f1) of this λ/4 SIR

22. DUAL-BAND NET-TYPE RESONATOR Since the electrical lengths of two sections of the SIR are set to equal,thenet-type resonator can be folded to a square box shape as shown in Fig. 1(d-2). The low impedance line can be equivalent to three parallelconnected stubs as shown in Fig. 1(c-2).

23. DUAL-BAND NET-TYPE RESONATOR Note that neither the value of K nor ƒ2/ƒ1 is restricted to an integer. Fig. 3 shows the resonant frequencies of the net-type resonators with K = 1.57 (ƒ2/ƒ1 = 2.5) and K = 3 (ƒ2/ƒ1 = 3) Fig. 3. Resonant frequencies of the net-type resonator with K = 1.57and 3.

24. DESIGN OF DUAL-BAND FILTER The resonators 1 and 4 are designed to simultaneously operate at the center frequencies ƒ1 and ƒ2 of he first and second passbands. The resonators 2Iand 3Iare designed to operate at ƒ1 while the resonators 2IIand 3IIare designed to operate at ƒ2 (a) Coupling structure

25. DESIGN OF DUAL-BAND FILTER The filter is fabricated on a RO4003 substrate with a thickness of 0.508 mm, a dielectric constant of 3.38, and a loss tangent of 0.0027. The center frequencies of two passbands are set To ƒ1 =1 GHz and ƒ2 =2 GHz schematic layout of the dual-band BPF using net-type resonators.

26. DESIGN OF DUAL-BAND FILTER • Substituting ƒ1 and ƒ2 into (1), one can obtain the impedance ratio K = 3 , and then calculate the electrical length Ɵ = 60o (1) • using (2). Here Z1and Z2are chosen as 60Ωand 20Ω, respectively. (2) • The fractional bandwidths (FBWs) of first and second passbands are ∆1 = 4.6% and ∆2 = 4.8%

27. SIMULATED AND MEASURED RESULTS It occupies a circuit size of 41.83 X 31.73 mm2. The simulated and measured results are illustrated in Fig. 5(b), and their enlarged views of the responses are given in Fig. 5(c). Circuit photograph of the developed filter. Simulated and measured results covering two passbands and their enlarged views of responses.

28. SIMULATED AND MEASURED RESULTS • the mid-band rejection between two passbands is greater than 40 dB from 1.14 GHz to 1.75 GHz. • It is because the open stub in the resonator 1 or 4 individually gives a transmission zero at around 1.5 GHz. • then the coupling between resonators 1 and 4 makes two transmission zeros split at 1.33 and 1.55 GHz.

29. 報告到此結束 謝謝聆聽