1 / 45

Lab 1: GPIO

Lab 1: GPIO. GPIO on MSP430. 6 ports on MS430F1611 Port 1 Port 2 Port 3 Port 4 Port 5 Port 6 Each port has 8 pins Px.0 ~ Px.7. Multiplexed. Port pins are often multiplexed Means it may have more than one function Example: P1.0/TACLK It can be P1.0 GPIO Or it can be TACLK

rana-phelps
Download Presentation

Lab 1: GPIO

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Lab 1: GPIO

  2. GPIO on MSP430 • 6 ports on MS430F1611 • Port 1 • Port 2 • Port 3 • Port 4 • Port 5 • Port 6 • Each port has 8 pins • Px.0 ~ Px.7

  3. Multiplexed • Port pins are often multiplexed • Means it may have more than one function • Example: P1.0/TACLK • It can be P1.0 GPIO • Or it can be TACLK • You must select the function you want

  4. Select Direction • Each pin can be configured as input or output • When set to output • You can configure it to be • High: voltage is Vcc (Supply voltage) • Low: voltage is GND (Ground) High: 3.3V Low: 0V

  5. Input • When you select a pin as input direction, a corresponding bit in peripheral register will • Set to 0 when input voltage is low • Set to 1 when input voltage is high High: 3.3V 1 0 Low: 0V

  6. Interrupts • Only P1 and P2 are interruptible • For each pin in P1 and P2, you can enable or disable its interrupt • Enable means it will detects interrupt • Disable means nothing happen when interrupt occur

  7. How to Detect Interrupts • For GPIO, interrupt is detected when a transition occur • Low to high transition: • High to low transition: • You must define which one you want to detect 3.3 V 0 V 3.3 V 0 V

  8. Interrupt Flag • When the MCU detects an interrupt • A corresponding bit in peripheral register will set to 1 • Branch to ISR • You must clear the GPIO interrupt flag in software • Means you must set the bit to 0 • or the program will re-enter the ISR again

  9. GPIO Registers • Each GPIO port has four registers • Input: PxIN • Output: PxOUT • Direction: PxDIR • Port Select(function select): PxSEL • P1 and P2 have three more • Interrupt flag: PxIFG • Interrupt edge select: PxIES • Interrupt enable: PxIE • Each register is 8-bit long • x represent the port number

  10. How to Select Function • You want to select this pin as GPIO(P1.0) function • The register related to function select • Port Select(function select): PxSEL • This is port 1, so the related register is P1SEL • From user guide

  11. How to Select Function • P1SEL is 8-bit long • Each bit corresponding to a pin in the port 7 0 P1SEL P1.6/TA1 P1.4/SMCLK P1.2/TA1 P1.0/TACLK P1.7/TA2 P1.5/TA0 P1.3/TA2 P1.1/TA0

  12. How to Select Function 7 0 • You want select P1.0/TACLK as P1.0 • Set the corresponding bit to 0 • In C: P1SEL = P1SEL & 0xFE; P1SEL P1.6/TA1 P1.4/SMCLK P1.2/TA1 P1.0/TACLK P1.7/TA2 P1.5/TA0 P1.3/TA2 P1.1/TA0 7 0 P1SEL

  13. Setting Bits Hexadecimal • P1SEL = P1SEL & 0xFE; • P1SEL &= 0xFE; • Usually, we use hexadecimal in setting registers • 0xFE = 11111110 (binary number) • Why P1SEL &= 0xFE; • Why not P1SEL = 0xFE; • The other registers are similar • check user guide

  14. GPIO Interrupt • All P1 pins source a single interrupt vector, and all P2 pins source a different single interrupt vector. • Interrupts generated by P1.0, P1.1, …, P1.7 all go to same ISR • How do you know which one generate the interrupt • check interrupt flag

  15. Hardware • LEDs • Switches • Keypad

  16. LEDs • This is a typical connection • When P1.1 set to high • DVcc = VP1.1 • no current flow • When P1.1 set to low • VP1.1 = 0 • Current flow through, turn on the LED • GPIO can use as an On/Off control R DVcc Vanode Vcathode

  17. Control LEDs • Look at Taroko schematic • which pins the LEDs connected to • These pins should be input direction or output direction? • How to set these pins to high (or low)

  18. Will This Work • Maybe, but you shouldn’t do this R Vcathode Vanode

  19. Max Current Source/Sink • Each pin has a maximum amount of current it can provide(source) or accept(sink) • For MSP430 • Max source: 6mA • Max sink: 6mA • Usually it can sink more current than it can source • You cannot use those pin as a power source (or sink) for any sensor/circuit directly

  20. Transistors • One of the fundamental building block of ICs • Two type: NPN, PNP • B: Base • C: Collector • E: Emitter • We will talk about NPN transistor • most commonly used

  21. Functional Model • A base current IB flows only when the voltage VBE across the base-emitter junction is 0.7V or more • Ic = hFE × IB (hFE is current gain) • The collector-emitter resistance RCEis controlled by the base current IB: • IB= 0   RCE = infinity   transistor off • IBsmall   RCE reduced   transistor partly on • IBincreased   RCE = 0   transistor full on ('saturated')

  22. Transistor as An On/Off Switch • Application Circuit  • Load is turn on when chip output is high • Choose a proper transistor and base resistor RB

  23. How To Choose • Transistor • Two parameter: Ic and hFE • Ic(max) must be larger than Iload (Ic) • Ic = hFE × IB hFE(min) > 5 x ((Ic) /(maximum output current from the chip)) • RB • RB =  (Vcc × hFE) / (5 × Ic) • choose the nearest standard value resistor

  24. Switches • Operation • Open: A and B are not connected in normal state • Close: When you press the button, A and B are connected • Typical circuit • When the switch is open, voltage of USERINT stay at high • When the switch is close, voltage of will be low A B

  25. Pull-up Resistor • R4 is a pull-up resistor • keep USERINT at high • What if we don’t have R4 • When it is open, USERINT is still high • When it is close • Short circuit USERINT

  26. Typical Value • Typical value of pull-up resistor • 10K ohm, 47K ohm, 100K ohm • Amount of current flow through when it close • I = V/R; Vcc = 3.3V, R = 10K ohm • I = 0.00033A = 330 μA • 330 μA, does it matter • for some type of switch, it is ok • close time very short • but not all, eg. reed switch

  27. Value of Pull-up • To save power, can we use very large pull-up resistor? • ans: No

  28. Impedance • Resistance: R = V/I • relation ship between the magnitude of the voltage and current • Impedance: Z = V/I (there are complex number) • relation ship between the magnitude and phase of the voltage and current

  29. Input Impedance This is a simplified analysis, we consider impedance as a resistance. Impedance is more complex than a simple resistance Vcc R1 Ri Z Ri

  30. Resistors in series • Ri is the input impedance of MSP430 GPIO pin • TI didn’t specify its value • but it should be larger than 10M ohm • R1 is pull-up resistor • if R1 is too large – R1 = Ri • then VMCUpin = Vcc / 2 • it is no longer a high state Vcc R1 VMCUpin Ri

  31. Debounce Capacitor • C9 is a debounce capacitor • Bounces • It could generate more than one interrupts when the switch is pressed

  32. HW/SW debounce • Hardware debounce • Capacitor will charge when the switch is open, and it will discharge when the switch is close (pressed) • Pros: smooth the line • Cons: increase the response time • Software debounce • Delay some time in the ISR • How long • you have to try out

  33. Keypad • This is a 3x4 matrix keypad • When you press a button, a pin in X and a pin in Y is connected • How to interface to MSP430?

  34. Today’s Labs • Flash a LED on Taroko • Toggle a LED when UserInt switch on Taroko pressed • Control on/off of a LED by UserInt switch, control another by reed switch • Connected a 3x4 Keypad to Taroko, flash the LEDs Red Green Yellow Flash once Flash twice

  35. JTAG Driver • C:\Program Files\IAR Systems\Embedded Workbench Evaluation 4.0\430\drivers\TIUSBFET\WinXP

  36. IAR Setting

  37. IAR Setting

More Related