1 / 24

HyperTransport™ Technology I/O Link

HyperTransport™ Technology I/O Link. Presentation by Mike Jonas. The I/O Bandwidth Problem. While microprocessor performance continues to double every eighteen months, the performance of the I/O bus architecture has lagged, doubling in performance approximately every three years.

rozalia-meszaros
Download Presentation

HyperTransport™ Technology I/O Link

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. HyperTransport™ Technology I/O Link Presentation by Mike Jonas

  2. The I/O Bandwidth Problem • While microprocessor performance continues to double every eighteen months, the performance of the I/O bus architecture has lagged, doubling in performance approximately every three years. • Every time processor performance doubles, latency only increases by a factor of 1.2.

  3. The I/O Bandwidth Problem

  4. The I/O Bandwidth Problem A number of new technologies are responsible for the increasing demand for additional bandwidth. • High-resolution, texture-mapped 3D graphics and high-definition streaming video are escalating bandwidth needs between CPUs and graphics processors. • Technologies like high-speed networking (Gigabit Ethernet, InfiniBand, etc.) and wireless communications (Bluetooth) are allowing more devices to exchange growing amounts of data at rapidly increasing speeds. • Software technologies are evolving, resulting in breakthrough methods of utilizing multiple system processors. As processor speeds rise, so will the need for very fast, high-volume inter-processor data traffic.

  5. The HyperTransport™ Technology Solution • HyperTransport is intended to support “in-the-box” connectivity • High-speed, high-performance, point-to-point link for interconnecting integrated circuits on a board. • Max signaling rate of 1.6 GHz on each wire pair, a HyperTransport technology link can support a peak aggregate bandwidth of 12.8 Gbytes/s.

  6. The HyperTransport™ Technology Solution

  7. HyperTransport™ Design Goals Improve system performance - Provide increased I/O bandwidth - Ensure low latency responses - Reduce power consumption Simplify system design - Use as few pins as possible to allow smaller packages and to reduce cost Increase I/O flexibility - Provide a modular bridge architecture

  8. HyperTransport™ Design Goals Maintain compatibility with legacy systems - Complement standard external buses - Have little or no impact on existing operating systems and drivers Ensure extensibility to new system network architecture (SNA) buses Provide highly scalable multiprocessing systems

  9. Flexible I/O Architecture • The physical layer defines the physical and electrical characteristics of the protocol. This layer interfaces to the physical world and includes data, control, and clock lines. • The data link layer includes the initialization and configuration sequence, periodic cyclic redundancy check (CRC), disconnect/reconnect sequence, information packets for flow control and error management, and double word framing for other packets. • The protocol layer includes the commands, the virtual channels in which they run, and the ordering rules that govern their flow. • The transaction layer uses the elements provided by the protocol layer to perform actions, such as reads and writes. • The session layer includes rules for negotiating power management state changes, as well as interrupt and system management activities.

  10. Device Configurations HyperTransport technology creates a packet-based link implemented on two independent, unidirectional sets of signals. It provides a broad range of system topologies built with three generic device types: • Cave—A single-link device at the end of the chain. • Tunnel—A dual-link device that is not a bridge. • Bridge—Has a primary link upstream link in the direction of the host and one or more secondary links.

  11. Device Configurations

  12. Electrical Configuration • The signaling technology used in HyperTransport technology is a type of low voltage differential signaling (LVDS ). • LVDS has been widely used in these types of applications because it requires fewer pins and wires. • Cost and power requirements are reduced because the transceivers are built into the controller chips.

  13. Minimal Pin Count? It would seem at a glance that they failed in their objective of lowering pin count because they require 2 pins per bit of data being transferred per direction. Why then do they claim to have reduced pin count? The increase in signal pins is offset by three factors: • Commands, addresses, and data (CAD) all share the same bits. • By using separate data paths, HyperTransport I/O links are designed to operate at much higher frequencies than existing bus architectures. This means that buses delivering equivalent or better bandwidth can be implemented using fewer signals. • Differential signaling provides a return current path for each signal, greatly reducing the number of power and ground pins required in each package.

  14. Minimal Pin Count? • The pin count for transferring 8 bits in parallel has definitely increased. • However more data can be transferred with fewer pins. Remember, 1.6 GHz wire rate.

  15. Signal Pins

  16. Maximum Bandwidth • HyperTransport links implement double data rate (DDR) transfer, where transfers take place on both the rising and falling edges of the clock signal. • An implementation of HyperTransport links with 16 CAD bits in each direction with a 1.6-GHz data rate provides bandwidth of 3.2 Gigabytes per second in each direction, for an aggregate peak bandwidth of 6.4 Gbytes/s, or 48 times the peak bandwidth of a 33-MHz PCI bus. • A low-cost, low-power HyperTransport link using two CAD bits in each direction and clocked at 400 MHz provides 200 Mbytes/s of bandwidth in each direction, or nearly four times the peak bandwidth of PCI 32/33.

  17. Perspective • What about PCI Express? PCI Express also uses LVDS Each data lane of a PCI Express card transmits 250 Mbytes/s in each direction. As shown here an 8 lane PCI express connector has 49 total pins

  18. Perspective • By comparison from table 3, an 8 lane wide bi-directional HyperTransport link requires 55 pins, 6 more than PCI Express. • This HyperTransport link can transmit 3.2 Gbytes/s, 1.2 Gbytes/s more than PCI Express • HyperTransport functions on half the voltage as PCI Express

  19. Protocol Layer • All HyperTransport technology commands are either four or eight bytes long and begin with a 6-bit command type field. The most commonly used commands are Read Request, Read Response, and Write.

  20. Session Layer • Link Width Optimization - All 16-bit, 32-bit, and asymmetrically-sized configurations must be enabled by a software initialization step. - After a cold reset BIOS reprograms all linked to the desired width

  21. Session Layer • Link Frequency Initialization - At cold reset, all links power-up with 200-MHz clocks. - Registers store supported clock frequencies - After some analysis Firmware then writes the two frequency registers to set the frequency for each link. - Once all devices have been configured, firmware initiates an LDTSTOP# disconnect or RESET# of the affected chain to cause the new frequency to take effect.

  22. HyperTransport Environments

  23. HyperTransport Environments

  24. Questions • http://www.hypertransport.org/docs/wp/25012A_HTWhite_Paper_v1.1.pdf

More Related