1 / 10

8259 Programmable Interrupt Controller

8259 Programmable Interrupt Controller. Block Diagram. Block Diagram description. Interrupt Request Register (IRR) and In-Service Register (ISR)

ryan-bell
Download Presentation

8259 Programmable Interrupt Controller

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. 8259 Programmable Interrupt Controller

  2. Block Diagram

  3. Block Diagram description • Interrupt Request Register (IRR) and In-Service Register (ISR) • The interrupts at the IR input lines are handled by two registers in cascade, the Interrupt Request Register (lRR) and the In- Service Register (lSR). The IRR is used to indicate all the interrupt levels which are requesting service, and the ISR is used to store all the interrupt levels which are currently being serviced

  4. Priority Resolver • This logic block determines the priorities of the bits set in the lRR. The highest priority is selected and strobed into the corresponding bit of the lSR during the INTA sequence. • Interrupt Mask Register (IMR) • The lMR stores the bits which disable the interrupt lines to be masked. The IMR operates on the output of the IRR. Masking of a higher priority input will not affect the interrupt request lines of lower priority.

  5. Data Bus Buffer • This 3-state, bidirectional 8-bit buffer is used to interface the PIC to the System Data Bus. Control words and status information are transferred through the Data Bus Buffer. • Read/Write Control Logic • The function of this block is to accept output commands from the CPU. It contains the Initialization Command Word (lCW) registers and Operation Command Word (OCW) registers which store the various control formats for device operation. This function block also allows the status of the PIC to be transferred onto the Data Bus. This function block stores and compares the IDs of all PICs used in the system. The associated three I/O pins (CAS0- 2) are outputs when the 8259 is used as a master and are inputs when the 8259 is used as a slave. As a master, the 8259 sends the ID of the interrupting slave device onto the CAS0 - 2 lines. The slave, thus selected will send its preprogrammed subroutine address onto the Data Bus during the next one or two consecutive INTA pulses.

  6. D[7..0] These wires are connected to the system bus and are used by the microprocessor to write or read the internal registers of the 8259. • A[0..0] This pin acts in conjunction with WR/RD signals. It is used by the 8259 to decipher various command words the microprocessor writes and status the microprocessor wishes to read. • WR When this write signal is asserted, the 8259 accepts the command on the data line, i.e., the microprocessor writes to the 8259 by placing a command on the data lines and asserting this signal. • RD When this read signal is asserted, the 8259 provides on the data lines its status, i.e., the microprocessor reads the status of the 8259 by asserting this signal and reading the data lines. • INT This signal is asserted whenever a valid interrupt request is received by the 8259, i.e., it is used to interrupt the microprocessor.

  7. INTA This signal, is used to enable 8259 interrupt-vector data onto the data bus by a sequence of interrupt acknowledge pulses issued by the microprocessor. • IR 0,1,2,3,4,5,6,7 An interrupt request is executed by a peripheral device when one of these signals is asserted. • CAS[2..0] These are cascade signals to enable multiple 8259 chips to be chained together. • SP/EN This function is used in conjunction with the CAS signals for cascading purposes

  8. Priority Modes • Fully Nested mode: All IRs are arranged in from lowest to highest priority. • Automatic Rotation mode: In this mode, a device after being served assumes the lowest priority. • Specific Rotation mode: This mode is same as ARM except that the user can select any IR for the lowest priority.

  9. End of Interrupt • Non Specific EOI Command: it resets the highest priority ISR bit. • Specific EOI Command: This command specifies which ISR bit to reset. • Automatic EOI Command: In this, the ISR bit is reset after the third INTA.

  10. Initialization command words(ICWs) • ICW1 and ICW2 LTIM (1 = Level-Triggered Interrupt Mode, 0 = Edge-Triggered Interupt Mode) ADI is length of Address-Interval for call-instruction (1 = 4-bytes, 0 = 8-bytes) SNGL (1 = single controller system, 0 = multiple controllers in cascade mode) IC4 means Initialization Command-Word 4 is needed (1 = yes, 0 = no) 0 A7 A6 A5 1 LTIM ADI SNGL IC4 ICW1 1 A15 / T7 A14 / T6 A13 / T5 A12 / T4 A11 / T3 A10 A9 A8 ICW2

More Related