Analog Discovery Design Kit Mini Course Webinar lecture #2 of 4

1. Analog Discovery Design KitMini Course Webinarlecture #2 of 4 Alan Rux Electrical and Computer Engineering Department University of Massachusetts Lowell Campus

2. Lecture # 2Two Channel Oscilloscope & Arbitrary Waveform Generator • Learning the ADK Leads (Analog Discovery Kit) • Oscilloscope Operation • F.F.T. Function

3. Leads are color coded

4. Leads we will be using today

5. You are now connected

6. To enable the oscilloscope click on the “Scope - in” icon

7. 2 Channel Oscilloscope Window

8. 2 Channel OscilloscopeMain Toolbar & Menu-Strip

9. 2 Channel OscilloscopeMain Toolbar & Menu-Strip

10. 2 Channel OscilloscopeMain Toolbar & Menu-Strip

11. 2 Channel OscilloscopeMain Toolbar & Menu-Strip

12. 2 Channel OscilloscopeMain Toolbar & Menu-Strip

13. 2 Channel Oscilloscope Main Toolbar Persistence Add XY Histogram Audio FFT Data Measure Current Audio Digital Events Zoom Options Help

14. Channel Toolbar Channel 1 & 2 Configuration(Vertical Gain, volts/cm )

15. Channel Toolbar Channel 1 & 2 Configuration(Vertical Gain, volts/cm ) Vertical Range 5V/div to 500uV/div In 1-2-5 steps

16. ChannelToolbar Channel 1 & 2 Configuration(Vertical Offset, volts/cm ) Offset Range +25V/div to -25V/div In 1-2-5 steps +/-100 mv., min. offset

17. Channel Toolbar Channel 1 & 2 Configuration(Horizontal Sweep, time/cm )

18. Channel Toolbar Channel 1 & 2 Configuration(Horizontal Sweep, time/cm ) Time Base 1hr./div to 10ns/div In 1-2-5 steps

19. Channel Toolbar Channel 1 & 2 Configuration(Trigger Position, time/cm ) Trigger Position +10hr./div to -10hr/div +/-5 usec., min. delay

20. Channel Toolbar Channel 1 & 2 Configuration(Trigger Configuration)

21. Trigger Mode: Normal – triggered on specified condition Auto – triggered on trigger condition, self starts in 2 seconds None – the acquisition is started without a trigger Channel Toolbar Channel 1 & 2 (Trigger Configuration)

22. Source: Channel 1 Channel 2 Digital AWG – 1 AWG – 2 Analyzer Patterns External – 1 External - 2 Channel Toolbar Channel 1 & 2 (Trigger Configuration)

23. Type of Trigger: Simple – is an edge trigger where the filter, hysteresis, and holdoff parameters are configured automatically. Level is set to 10% of the selected trigger channel range Channel Toolbar Channel 1 & 2 (Trigger Configuration)

24. Type of Trigger: Edge + slope-condition control Channel Toolbar Channel 1 & 2 (Trigger Configuration)

25. Type of Trigger: Pulse, will trigger if pulse has a smaller/larger length than the one set by the user. Channel Toolbar Channel 1 & 2 (Trigger Configuration) Set for Less then 200 usec.

26. Type of Trigger: Pulse, will trigger if pulse has a smaller/larger length than the one set by the user. Channel Toolbar Channel 1 & 2 (Trigger Configuration) Set for more then 200 usec.

27. Type of Trigger: Transition - the transition time of a signal as compared with a specified length Channel Toolbar Channel 1 & 2 (Trigger Configuration)

28. Type of Trigger: Transition - the transition time of a signal as compared with a specified length Channel Toolbar Channel 1 & 2 (Trigger Configuration)

29. Trigger Hysteresis – low and high leveles are determined to avoid bouncing caused by signal noise and also to specify the transition trigger conditions, 20 volts to 1mv and zero volts in 1 -2 -5 steps Channel Toolbar Channel 1 & 2 (Trigger Configuration)

30. Trigger Hysteresis Channel Toolbar Channel 1 & 2 (Trigger Configuration)

31. Trigger Holdoff –a adjustable time period during which the oscilloscope will not trigger . this is useful when triggering on complex waveform shapes, so the oscilloscope triggers only on the first eligible trigger point. Time range from 1 hour to 100nsec., in 1 – 2 – 5 steps and zero sec. Channel Toolbar Channel 1 & 2 (Trigger Configuration)

32. Channel Toolbar Channel 1 & 2 (Trigger Configuration)

33. Options: General, Display, Colors, Configuration Channel Toolbar Channel 1 & 2 (Options Configuration)

34. Channel Toolbar Channel 1 & 2 (Color Configuration)

35. Channel Toolbar Channel 1 & 2 (Color Configuration)

36. Main Toolbar F. F. T. function FFT View – plots amplitude against frequency, it shows the signals in the frequency domain as opposed to the time domain

37. 2 Channel OscilloscopeMain Toolbar – FFT function

38. Arbitrary Waveform Generator • the ADK Leads (Analog Discovery Kit) • Function Generator operation • Oscilloscope use

39. Leads are color coded

40. Leads we will be using today

41. Leads we will be using today Waveform Gen-1 (yellow) to Scope ch-1 (orange) Waveform Gen-1 common gnd. (black) to Scope ch-1 neg. (orange/white)

42. Analog Discovery BNC Adapter Board Allows the use of standard BNC-terminated test leads & probes on your Analog Discovery Selectable AC and DC coupling to oscilloscope probes Selectable 50-ohm or 0-ohm output impedance on Arbitrary Waveform Generator (AWG) channels

43. You are now connected

44. To enable the Waveform Gen. click on the “WaveGen - out” icon

45. Waveform Generator Window1 Channel, AWG-1

46. also enable the oscilloscope click on the “Scope - in” icon

47. 2 Channel Oscilloscope Window

48. Waveform Generator Window AWG-1 & AWG-2

49. Waveform Gen./Scope Window1 Channel Oscilloscope & AWG-1 AWG scope

50. AWG main window