1 / 36

Caterpillar Cat 972G II WHEEL LOADER (Prefix AXE) Service Repair Manual (AXE00001 and up)

To get the complete manual, please open the home page website.<br><br>https://www.aservicemanualpdf.com/

tgyhuhnk7m8u
Download Presentation

Caterpillar Cat 972G II WHEEL LOADER (Prefix AXE) Service Repair Manual (AXE00001 and up)

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Service Repair Manual Models 972G II WheelLoader

  2. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-U... 1/27 Shutdown SIS Previous Screen Product: WHEEL LOADER Model: 972G II WHEEL LOADER AXE Configuration: 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-UP (MACHINE) POWERED BY 3196 ENGINE Disassembly and Assembly 966G Series II and 972G Series II Wheel Loaders Power Train Media Number -RENR4365-07 Publication Date -01/08/2008 Date Updated -14/08/2008 i02299775 Transmission Planetary - Disassemble SMCS - 3160-015 Disassembly Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 138-7575 Link Bracket 3 B 1P-0520 Driver Gp 1 C 8H-0663 Bearing Puller 1 Start By: A. Separate the transmission from the output transfer gears. Refer to Disassembly and Assembly, "Transmission from Output Transfer Gears - Separate". Note: Cleanliness is an important factor. Before the disassembly procedure, the exterior of the component should be thoroughly cleaned. This will help to prevent dirt from entering the internal mechanism. Note: Put identification marks on all lines, on all hoses, on all wires, and on all tubes for installation purposes. Plug all lines, hoses, and tubes. This helps to prevent fluid loss and this helps to keep contaminants from entering the system. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  3. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-U... 2/27 Illustration 1 g00458960 1. Remove O-ring seal (1) from the housing. 2. Remove bolt (3), retainer (2), and drive gear (4) from the end of the input shaft. Illustration 2 g00459007 3. Remove plate (5) . Illustration 3 g00459030 4. Attach Tooling (A) and a suitable lifting device to the transmission, as shown. The weight of the transmission is approximately 544 kg (1200 lb). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  4. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-U... 3/27 5. Carefully position the planetary group on the opposite end so that No. 6 clutch housing (6) is facing upward, as shown. Illustration 4 g00459073 6. Remove retaining ring (8) from output shaft (7) . Illustration 5 g00459075 Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. 7. Remove bolts (9) and No. 6 clutch housing (6). Mark the location of the long bolts. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  5. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-U... 4/27 Illustration 6 g00459079 8. Remove clutch piston (10) from No. 6 clutch housing (6) . 9. Remove seal rings (11) and (12) from clutch piston (10) . Illustration 7 g00459087 10. Remove clutch plate (14) and springs (13) . Illustration 8 g00459090 11. Remove clutch plates (15) and friction discs (16) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  6. https://www.aservicemanualpdf.com/ My Dear Friend! Thank you very much for visiting. Full manual if required, please enter the following URL into your browser. https://www.aservicemanualpdf.com/

  7. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-U... 5/27 Illustration 9 g00459103 12. Remove ring gear (17). Remove transmission speed sensors (18) . Illustration 10 g00459133 13. Remove carrier assembly (19) . Illustration 11 g00459138 14. Remove metal seal ring (20) from carrier assembly (19) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  8. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-U... 6/27 Illustration 12 g00459150 15. Use a hammer and a punch to push the spring pins through carrier assembly (19) and into planetary shafts (21) . Illustration 13 g00459151 16. Use a hammer and a punch to remove planetary shafts (21) from carrier assembly (19) . Illustration 14 g00324725 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  9. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-U... 7/27 17. Remove thrust discs (22), planetary gears (23), and bearings (24) from the carrier assembly. Remove spring pins (25) from planetary shafts (21) . Illustration 15 g00459161 18. Remove O-ring seal (26). Remove bolts (27) from manifold (28) . Illustration 16 g00565113 19. Disconnect the harness assemblies which are attached to transmission modulating valves (29). Remove transmission modulating valves (29) from the transmission housing. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  10. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-U... 8/27 Illustration 17 g00459316 20. Remove retaining ring (32) and gear (30). Remove retaining ring (31) . Illustration 18 g00459322 21. Use Tooling (A) and a suitable lifting device to remove manifold (28). The weight of manifold (28) is approximately 85 kg (190 lb). 22. Remove bolt (33) which holds the harness assembly in place. Illustration 19 g00459352 23. Remove retaining ring (34) and bearing (35) from manifold (28) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  11. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-U... 9/27 Illustration 20 g00459369 24. Remove retaining ring (36) and clutch housing (37) . Illustration 21 g00459372 25. Remove O-ring seal (38) from clutch housing (37) . Illustration 22 g00459375 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  12. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-... 10/27 Personal injury can result from being struck by parts propelled by a released spring force. Make sure to wear all necessary protective equipment. Follow the recommended procedure and use all recommended tooling to release the spring force. 26. Use steel spacers and a suitable press to push on retainer plate (40). Remove retaining ring (39) from the clutch housing. Illustration 23 g00459387 27. Separate retaining ring (39), retainer plate (40), three coned disc springs (41), and clutch piston (42) . Illustration 24 g00459393 28. Remove seal rings (43) from clutch piston (42) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  13. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-... 11/27 Illustration 25 g00459394 29. Remove seal rings (44) from clutch housing (37) . Illustration 26 g00565119 30. Remove retaining ring (45) from the output shaft. Remove hub (46) . Illustration 27 g00565685 31. Remove friction discs (47) and clutch plates (48) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  14. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-... 12/27 Illustration 28 g00565132 32. Remove clutch plate (49) and ring gear (50) . Illustration 29 g00565193 33. Remove springs (51). Remove friction discs (52) and clutch plates (53) . Illustration 30 g00565687 34. Remove clutch piston (54). Remove O-ring seals (55) and (56) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  15. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-... 13/27 Illustration 31 g00459506 35. Remove seal rings (57) and (58) from clutch piston (54) . Illustration 32 g00565199 36. Use Tooling (A) and a suitable lifting device to remove housing (59). The weight of housing (59) is approximately 66 kg (145 lb). Note: The clutch piston may be stuck in housing (59). As housing (59) is removed, the clutch piston may fall. Illustration 33 g00565203 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  16. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-... 14/27 37. Remove clutch piston (60) . Illustration 34 g00459540 38. Remove seal rings (61) and (62) from clutch piston (60) . Illustration 35 g00565255 39. Remove friction discs (63) and clutch plates (64) . Illustration 36 g00565689 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  17. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-... 15/27 40. Remove O-ring seals (65) and (66). Remove springs (68) and carrier assembly (69). Remove rods (67) . Illustration 37 g00459619 41. Remove gear (70) from carrier assembly (69) . Illustration 38 g00459622 42. Remove retaining ring (71) and bearing (72) . Illustration 39 g00459634 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  18. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-... 16/27 43. Use several small steel rods (73) (3.175 mm (0.1250 inch) diameter and one pointed tip) to compress the retaining ring that holds carrier assembly (69) to ring gear (74) . 44. Remove carrier assembly (69) from ring gear (74) . Illustration 40 g00459638 45. Remove retaining ring (75) from carrier assembly (69) . Illustration 41 g00459643 46. Use a hammer and a punch to push the spring pins through carrier assembly (69) and into planetary shafts (76) . 47. Use a hammer and a punch to remove planetary shafts (76) from carrier assembly (69) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  19. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-... 17/27 Illustration 42 g00459646 48. Remove thrust discs (77), planetary gears (78), and bearings (79) from the carrier assembly. Remove spring pins (80) from planetary shafts (76) . Illustration 43 g00565272 49. Remove retaining ring (81) that holds output shaft (82) to the input shaft. Remove output shaft (82) . Illustration 44 g00459776 50. Remove O-ring seal (83) from output shaft (82) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  20. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-... 18/27 Illustration 45 g00460029 51. Remove retaining ring (85) . 52. Remove sun gear (84) from output shaft (82) . Illustration 46 g00460030 53. Use a suitable press to push output shaft (82) out of bearing (86), as shown. Illustration 47 g00460034 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  21. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-... 19/27 54. If necessary, remove bearings (87) from both ends of output shaft (82) . Illustration 48 g00565282 55. Use Tooling (A) and a suitable lifting device to remove housing (88). The weight of housing (88) is approximately 61 kg (135 lb). Illustration 49 g00460042 56. Remove clutch piston (89), friction discs (90), and clutch plates (91) . Illustration 50 g00460045 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  22. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-... 20/27 57. Remove seal rings (92) and (93) from clutch piston (89) . Illustration 51 g00460067 58. Remove retaining ring (94) from the input shaft. 59. Remove springs (95) and ring gear (96). Remove O-ring seals (97) and (98) . Illustration 52 g00460068 60. Remove carrier assembly (99) from the input shaft. The weight of the carrier assembly is approximately 29 kg (65 lb). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  23. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-... 21/27 Illustration 53 g00460074 61. Remove gear (100) . 62. Place a suitable wood block under carrier assembly (99) . 63. Use several small steel rods (101) (2.36 mm (0.093 inch) diameter and one pointed tip) to compress the retaining ring that holds carrier assembly (99) to ring gear (102) together. 64. Remove ring gear (102) from carrier assembly (99) . Illustration 54 g00460078 65. Remove retaining ring (105) from carrier assembly (99) . 66. Remove retaining ring (104). Remove sun gear (103) and the bearing. Use Tooling (B) to remove sun gear (103) and the bearing. Illustration 55 g00460081 67. Use a hammer and a punch to push the spring pins through carrier assembly (99) and into planetary shafts (106) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  24. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-... 22/27 Illustration 56 g00460134 68. Use a hammer and a punch to remove planetary shafts (106) from carrier assembly (99) . Illustration 57 g00460135 69. Remove thrust discs (107), bearings (109), and planetary gears (108) from the carrier assembly. 70. Remove spring pins (110) from planetary shafts (106) . Illustration 58 g00460138 71. Remove bearing (111) from sun gear (103) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  25. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-... 23/27 Illustration 59 g00460141 72. Remove O-ring seal (112) from sun gear (103) . Illustration 60 g00460178 73. Remove plate (113) . Illustration 61 g00460181 74. Remove friction discs (114) and clutch plates (117). Remove O-ring seals (115) and (116) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  26. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-... 24/27 Illustration 62 g00460207 75. Use several small steel rods (118) (2.36 mm (0.093 inch) diameter and one pointed tip) to compress the retaining ring that holds coupling (120) to carrier assembly (119). Remove coupling (120) from carrier assembly (119) . Note: Coupling (120) and carrier assembly (119) may be removed together at this time. Use small steel rods (118) in order to separate coupling (120) and carrier assembly (119). See Step 43 for similar actions. Illustration 63 g00460208 76. Remove clutch piston (121) from the clutch housing. Remove carrier assembly (119) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  27. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-... 25/27 Illustration 64 g00460209 77. Remove seal rings (122) and (123) from clutch piston (121) . Illustration 65 g00460233 78. Remove retaining ring (124). Use Tooling (B) to remove bearing (125) . 79. Remove seal ring (126) from carrier assembly (119) . Illustration 66 g00460237 80. Use a hammer and a punch to push the spring pins through carrier assembly (119) and into planetary shafts (127) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  28. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-... 26/27 81. Use a hammer and a punch to remove planetary shafts (127) from carrier assembly (119) . Illustration 67 g00460313 82. Remove thrust discs (128), planetary gears (129), and bearings (130) from the carrier assembly. Remove spring pins (131) from planetary shafts (127) . Illustration 68 g00460315 83. Remove retaining ring (132) from housing (133) . 84. Use a soft hammer to remove input shaft (134) from housing (133) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  29. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-... 27/27 Illustration 69 g00460318 85. Remove ring seals (136) and O-ring seal (137) from input shaft (134). Remove bearing (135) . Illustration 70 g00460322 86. Use a suitable press and Tooling (C) to remove race (138) from input shaft (134) . Copyright 1993 - 2021 Caterpillar Inc. Sun May 9 12:26:31 UTC+0800 2021 All Rights Reserved. Private Network For SIS Licensees. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  30. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-U... 1/28 Shutdown SIS Previous Screen Product: WHEEL LOADER Model: 972G II WHEEL LOADER AXE Configuration: 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-UP (MACHINE) POWERED BY 3196 ENGINE Disassembly and Assembly 966G Series II and 972G Series II Wheel Loaders Power Train Media Number -RENR4365-07 Publication Date -01/08/2008 Date Updated -14/08/2008 i06064263 Transmission Planetary - Assemble SMCS - 3160-016 Assembly Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 138-7575 Link Bracket 3 B 1P-0520 Driver Gp 1 D FT-2746 Guide Pin 2 E 1P-0510 Driver Gp 1 F - Loctite 5127 1 Note: Cleanliness is an important factor. Before assembly, all parts should be cleaned in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts. Lint may be deposited on the parts. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  31. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-U... 2/28 Illustration 1 g00460318 Note: O-ring seal (137) is not installed at this time. The O-ring seal is shown in order to clarify the installation in Step 11. 1. Raise the temperature of bearing (135) and the race. Install bearing (135) and the race onto input shaft (134) , as shown. 2. Apply clean transmission oil to ring seals (136) . Install two ring seals (136) on input shaft (134) . Illustration 2 g00460315 3. Carefully install input shaft (134) in housing (133) . 4. Install retaining ring (132) in order to hold the input shaft and the bearing in place. Illustration 3 g00460313 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  32. GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/ Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it. GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/

  33. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-U... 3/28 Illustration 4 g00460237 5. Install bearings (130) in planetary gears (129) . Install the gear assemblies, thrust discs (128) , and planetary shafts (127) in carrier assembly (119) . 6. Use a hammer and a punch to install spring pins (131) that hold planetary shafts (127) in carrier assembly (119) . Make sure that the spring pins are flush with the counterbore in the carrier. Illustration 5 g00460233 7. Install seal ring (126) on carrier assembly (119) . 8. Use Tooling (B) to install bearing (125) . Install retaining ring (124) . Note: Coupling (120) may be installed on carrier assembly (119) at this time. Refer to Step 13 for the procedure. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  34. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-U... 4/28 Illustration 6 g00460209 9. Install seal rings (122) and (123) on clutch piston (121) . Illustration 7 g00460208 10. Place suitable cribbing under the housing. Install clutch piston (121) in the clutch housing. Make sure that the lips of the seals are facing downward. 11. Install O-ring seal (137) . Apply clean transmission oil to O-ring seal (137) and the O-ring seal groove on the shaft. Refer to Illustration 1 for the location of the O-ring seal. 12. Install carrier assembly (119) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  35. 972G SERIES II WHEEL LOADER /COMMAND CONTROL STEE/ AXE00001-U... 5/28 Illustration 8 g00460207 13. If necessary, install coupling (120) on carrier assembly (119) . Use small steel rods (118) to compress the retaining ring that holds coupling (120) to carrier assembly (119) . Illustration 9 g00460934 Illustration 10 g00720054 Note: For assembly purposes, use Tooling (D) to hold the clutch plates in place. Do not remove Tooling (D) until Step 85 is completed. 14. Install one clutch plate (117) in the housing so that the small hole in the clutch plate is aligned with the small hole in the housing, as shown. 15. Install Tooling (D) in two of the five threaded holes in the housing through clutch plate (117) , as shown. Do not remove Tooling (D) until Step 85 is completed. 16. Install friction discs (114) and clutch plates (117) in alternating order. Start with a friction disc. Install clutch plates (117) so that Tooling (D) passes through the bolt holes in the clutch plates. Install the clutch plates with the small holes on the opposite side of Tooling (D) in comparison to the first clutch plate (117) that was installed in Step 14. 17. Install O-ring seals (115) and (116) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw... 2021/5/9

  36. https://www.aservicemanualpdf.com/ My Dear Friend! Thank you very much for visiting. Full manual if required, please enter the following URL into your browser. https://www.aservicemanualpdf.com/

More Related