1 / 17

CHE/ME 109 Heat Transfer in Electronics

CHE/ME 109 Heat Transfer in Electronics. LECTURE 20 – SPECIFIC NATURAL CONVECTION MODELS. SPECIFIC NATURAL CONVECTION MODELS. EXTENDED SURFACES THE NUSSELT NUMBER FOR FINNED SYSTEMS IS BASED ON THE SPACING BETWEEN FINS, S, AND THE FIN HEIGHT, L: FOR CONSTANT SURFACE TEMPERATURE.

thora
Download Presentation

CHE/ME 109 Heat Transfer in Electronics

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. CHE/ME 109 Heat Transfer in Electronics LECTURE 20 – SPECIFIC NATURAL CONVECTION MODELS

  2. SPECIFIC NATURAL CONVECTION MODELS • EXTENDED SURFACES • THE NUSSELT NUMBER FOR FINNED SYSTEMS IS BASED ON THE SPACING BETWEEN FINS, S, AND THE FIN HEIGHT, L: • FOR CONSTANT SURFACE TEMPERATURE

  3. EXTENDED SURFACES • FOR CONSTANT HEAT FLUX:

  4. VERTICAL FINS • PARAMETERS FOR THESE EQUATIONS: • VERTICAL ISOTHERMAL FINS (EQN 9-31) • TRANSFER FROM BOTH SIDES: C1 = 576, C2 = 2.87 • ONE SIDE ADIABATIC: C1 = 144, C2 = 2.87 • VERTICAL CONSTANT HEAT FLUX FIND (EQN 9-36) • TRANSFER FROM BOTH SIDES: C1 = 48, C2 = =2.51 ONE SIDE ADIABATIC: C1 = 24, C1 = 2.51

  5. TYPICAL INSTALLATIONS • ALTERNATE CONFIGURATIONS FOR COOLING FINS http://www.thermalsoftware.com/vert_vs_horz_sink.pdf

  6. OPTIMUM VERTICAL FIN SPACING • BALANCE BETWEEN FLOW CROSS-SECTION AND SURFACE AREA http://www.thermalsoftware.com/vert_vs_horz_sink.pdf

  7. OPTIMUM VERTICAL FIN SPACING • A FUNCTION OF MATERIALS Avram Bar-Cohen,*, Raj Bahadur, Madhusudan Iyengar, Least-energy optimization of air-cooled heat sinks for sustainability-theory, geometry and material selection, Energy 31 (2006) 579–619

  8. OPTIMUM VERTICAL FIN SPACING • ALSO A FUNCTION OF FIN THICKNESS Avram Bar-Cohen,*, Raj Bahadur, Madhusudan Iyengar, Least-energy optimization of air-cooled heat sinks for sustainability-theory, geometry and material selection, Energy 31 (2006) 579–619

  9. OPTIMUM VERTICAL FIN SPACING • ISOTHERMAL FINS: • OPTIMUM NUSSELT: Nu = 1.307 = hSopt/K • TRANSFER FROM BOTH SIDES (EQN 9-32): Sopt = 2.714(S3L/Ras) 1/4 • CONSTANT HEAT FLUX • TRANSFER FROM BOTH SIDES (EQN 9-37): Sopt = 2.12(S4L/Ra*s)1/5 • PROPERTIES FOR THESE CORRELATIONS ARE ALL BASED ON AN AVERAGE VALUE FOR THE FILM TEMPERATURE

  10. NATURAL CONVECTION INSIDE ENCLOSURES • THERE ARE MANY RESEARCH PROJECTS FOR THIS SYSTEM, SO THEREFORE MANY CORRELATIONS • HEAT FLUX ACROSS AN ENCLOSURE IS TYPICALLY EXPRESSED AS Q = hA(T1 - T2) • h DEPENDS STRONGLY ON THE ASPECT RATIO, H/L • THE Ra NUMBER FOR THIS SYSTEM IS DEFINED IN TERMS OF THE SPACING BETWEEN HEATED PLATES, L:

  11. NATURAL CONVECTION INSIDE ENCLOSURES • FOR LOW RALEIGH NUMBERS, Ra < 1000, DUE TO CLOSE PLATE SPACING: • THERE IS MINIMAL BOUYANCY DRIVEN FLOW • .THIS BECOMES A CONDUCTION SYSTEM

  12. HORIZONTAL RECTANGULAR ENCLOSURES • INSULATED ON THE ENDS • THERE IS NO TRANSFER WHEN THE TOP TEMPERATURE IS GREATER THAN THE BOTTOM • THERE IS SIGNIFICANT TRANSFER WHEN THE BOTTOM TEMPERATURE IS GREATER THAN THE TOP AND Ra > 1700 • FOR THIS CONDITION, THERE ARE LOCAL CIRCULATION CELLS FOR 1700 < Ra < 5x104 • FOR HIGHER Ra NUMBERS, THE FLOW IS TURBULENT • CORRELATIONS: • TEXT (9-47) IS GENERAL • (9-44 THRU 9-46) ARE BASED ON SPECIFIC COMPONENTS

  13. VERTICAL RECTANGULAR ENCLOSURES • CORRELATIONS ARE BASED ON ASPECT RATIOS • NOTE THE GENERAL CORRELATIONS IN THE TEXT (9-52 THRU 9-53) CAN BE APPLIED TO HORIZONTAL ENCLOSURES AS WELL AS VERTICAL ENCLOSURES.

  14. CONCENTRIC CYLINDERS • FOR VERTICAL SYSTEMS, THE VERTICAL RECTANGULAR CORRELATIONS MAY BE USED • FOR HORIZONTAL SYSTEMS • EQUATIONS USE A MODIFIED CONDUCTION MODEL: • kEff IS CALCULATED FROM: • L = Do - Di AND Lc = (Do - Di)/2 • PROPERTIES ARE BASED ON AVERAGE TEMPERATURE

  15. CONCENTRIC SPHERES • EMPLOY THE CONCEPT OF kEff • kEff IS CALCULATED FROM: • L = Do - Di AND Lc = (Do - Di)/2 • PROPERTIES ARE BASED ON AVERAGE TEMPERATURE

  16. COMBINED NATURAL & FORCED CONVECTION • FACTOR APPLIED WHEN MODELING A SYSTEM WITH BOTH FORMS OF CONVECTION IS Gr/Re2 • WHEN Gr/Re2 << 1, THEN NATURAL CONVECTION CAN BE IGNORED • WHEN Gr/Re2 >> 1, THEN FORCED CONVECTION CAN BE IGNORED

  17. COMBINED NATURAL & FORCED CONVECTION • FOR CONDITIONS WHERE 0.1 < Gr/Re2 < 10, THEN BOTH MECHANISMS ARE SIGNIFICANT • THE NUSSELT FOR THIS COMBINED CONDITION IS TYPICALLY MODELED WITH • n = 3 FOR A WIDE RANGE OF SYSTEMS • n = 7/2 OR 4 APPEARS TO WORK BETTER FOR TRANSVERSE FLOWS OVER HORIZONTAL PLATES OR HORIZONTAL CYLINDERS

More Related