1 / 16

Lecture 5: Charged particles

Lecture 5: Charged particles. Charged particle data from the text As time permits=>Source distributions. Charged particle curves. Charged particle coefficients. HW 5.1. Use Table 3.6 to find the range of a 20 MeV proton in water. Check it with Figure 3.15.

vianca
Download Presentation

Lecture 5: Charged particles

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Lecture 5: Charged particles • Charged particle data from the text • As time permits=>Source distributions

  2. Charged particle curves

  3. Charged particle coefficients

  4. HW 5.1 • Use Table 3.6 to find the range of a 20 MeV proton in water. Check it with Figure 3.15. • Repeat the problem using MCNP6.

  5. MCNP Example: Add plane surfaces c cells 1 1 -1.0 -100 101 -1 2 1 -1.0 -100 1 -2 3 1 -1.0 -100 2 -3 4 1 -1.0 -100 3 -4 5 1 -1.0 -100 4 -5 6 1 -1.0 -100 5 -6 7 1 -1.0 -100 6 -7 8 1 -1.0 -100 7 -8 9 1 -1.0 -100 8 -9 10 1 -1.0 -100 9 -10 102 0 #(-100 101 -10) -999 999 0 999 c surfaces 100 cx 3 101 px 0 1 px .1 2 px .2 3 px .3 4 px .4 5 px .5 6 px .6 7 px .7 8 px .8 9 px .9 10 px 1.0 999 sph 0 0 0 1000

  6. MCNP Example: Add plane surfaces

  7. HW 5.2 • We are fond of saying that alpha particles are “stopped” by a piece of paper. Use Table 3.6 (with corrections) to determine the energy of an alpha particle that would have a range of 1 cm in water. • Repeat the problem using MCNP6.

  8. MCNP6 particles (subset!)

  9. HW 5.3 • Give me a source-height neutron flux map from a 5 MeV neutron point source in the center of a 10’x10’x10’ room. • There is an identical room (through an intervening wall) next to the room the wall is in. • Assume that the walls are 6” thick concrete. • This is BOTH the xy and the xz view (the + is the source):

  10. Set up a Mesh Tally • This is a mesh of rectangles (you can also do a cylindrical mesh) that the answer will be collected on. • This uses the FMESH card, with the following syntax: FMESHx4:n ORIGIN x0 y0 z0 IMESH x1 IINTS nx JMESH y1 JINTS ny KMESH z1 KINTS nz OUT ij where: (x0,y0,z0) is the lower left corner of the mesh (x1,y1,z1) is the upper right corner of the mesh nx,ny,nz tell how many divisions there are in the mesh in the 3 dimensions OUT ij indicates that you want an (x,y) grid of points (for each z level) (You can use other combinations (e.g., jk would give you a (y,z) grid for each x level)

  11. Set up a Mesh Tally (2) • The mesh itself is put into a file that has ..msht added to your file name • This is if you use the name=file syntax to run MCNP6. Otherwise look for it among the newer files created. • This is how I generally view it in EXCEL: • Open EXCEL • Open the mesh tally file using an editor that you can cut-and-paste from • Go to the line just under the “Tally results” line and copy the entire grid into the EXCEL file • Be aware that it may put each row in a SINGLE cell in the column. If so, highlight the column and use “Data” and “Text to columns” and “Finish” to spread out the rows. • Highlight (grab) the entire table from the upper left hand corner to the lower right (including the x and y coordinates) • Choose “Insert” “Other charts…” and any of the Surface plots • I like to use “Layout” “Axes” “Primary Vertical Axis” to: • Change to a logarithmic scale with Base 2 or Base 10 (depending on what looks best) • Set the color ranges so the colors represents factors of 2 or 10 using the • I also like to click on “3D Rotation” and play with the view (although I also like the “straight down” view using the colors as 2D isoflux lines

  12. Set up a Mesh Tally (3) Test of FMESH tally c cells 1 0 -1 2 2 1 -11.35 -2 999 0 1 c surfaces 1 sph 0 0 0 1000 2 rpp 50 55 -100 100 -100 100 c data mode p sdef erg=2 pos = 0 0 0 par=2 fmesh4:p origin -500 -500 -1 imesh 500 jmesh 500 kmesh 1 iints 40 jints 40 kints 1 out ij imp:p 1 1 0 m1 82000 1

  13. Set up a Mesh Tally (4)

  14. Set up a Mesh Tally (5)

  15. Set up a Mesh Tally (6)

  16. Review for test

More Related