1 / 14

Assembly Instructions DucoSlide Luxframe 40/80 Linear 115

FRONT SIDE. BACK SIDE. TOP. Assembly Instructions DucoSlide Luxframe 40/80 Linear 115. L.H. R.H. BOTTOM. Parts Breakdown. Parts Breakdown. Parts List All cut lengths of the individual parts are specified in the parts list.

willoughby-roland
Download Presentation

Assembly Instructions DucoSlide Luxframe 40/80 Linear 115

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. FRONT SIDE BACK SIDE TOP Assembly Instructions DucoSlide Luxframe 40/80 Linear 115 L.H. R.H. BOTTOM

  2. Parts Breakdown

  3. Parts Breakdown

  4. Parts List • All cutlengths of the individualparts are specified in the parts list. • The distance “center onderste gat tot zaagsnede” (center-to-centerdistancefrombottom hole to cuttingline) is to beusedforcutting the punchedsections to length.Thisdistanceshouldbepassed to the productiondepartment.

  5. MOUNTING SEQUENCE 1. Sizing * Cut both the top rail and the bottom rail off square : length = slide width - 80 mm (twice the width of the stile). * Cut the blades to the same length as the top and bottom rail. * Cut a LH and a RH vertical pre-punched profile down to size taking into account the symmetric distribution of the hole pattern : length = slide width – 6 mm (twice the width of the cover plate. Since the cover cap is not cut at the same time as the vertical profile, a - 0.5 mm up to - 1 mm tolerance on the length of the vertical profile needs to be taken into account to make sure the cover cap can be retrofitted.

  6. 2. Mounting Preparations * Using the drilling jig, drill 6.2 mm holes in the top and bottom of the vertical profiles. Make sure the drilling jig is a tight fit against the extreme end of the vertical profiles and hold it in position using a quick action clamp or an F-clamp.

  7. 3. Fitting the Slide Make sure to use the correct screw bit for each type of screw drive (PH 2, Pz 2, PZ 3) and adjust the tightening torque of the drill/screwdriver to the screws involved. * Fit a cover plate to either end of the vertical profiles using two A2 stainless steel M4 x 20 DIN 7500 Form M screws with PZ 2 drive. * Slide the top and bottom rail, with the visible drill groove facing outwards, in between the vertical profiles and secure them on one side using A2 stainless steel M6 x 25 DIN 7500 Form C screws with PZ 3 drive for each rail. For the other vertical profile, screw the screws a few turns leaving enough room for the blades to be a sliding fit. * Place the blades in the positioning jig and make sure both front and back of the blades lie flush with the stile first and then fix each in place on one side using two A2 stainless steel M6 x 25 DIN 7500 Form C screws with PZ 3 drive. On the opposite side, tighten each screw by only a few turns.

  8. That's how the positioning jig looks like. * Now push the remaining vertical profile fully home against the already assembled items. Firmly tighten the screws of the top and bottom rail first and then those securing the blades. * Check the slide for squareness by taking measurements across the diagonals using a tape measure. * Where appropriate, make sure you have the slide flat on a tabletop if it does not fit flat against (tilted to one side) this work surface. * Fit the cover caps to the vertical profiles.

  9. 4. Fittings Mounting * Place the suspension bracket(G0013031 or G0013080)on the top rail of the slideusing the positioningjig. Be sure the hole provided in the suspension bracket, to accommodate the suspension bracketscrew, pointstowards the rear of the slide. Fastenitwithfour A2 stainless steel M 4.8 x 18 DIN 7504-M self-drillingscrewswith PH 2 drive. Do thisforbothsides of the slide. * A choice of threepossiblefixingpositions of the suspension bracket(G0013031 or G0013080) is available: These positionsvarydependinguponwhat the customerordered ! • Standard position at 150 mm for all slides ; • At 195 mm fortelescopic and symmetricslideson the return pulleyside ; • At 260 mm for the side of the slideunderneath the actuator, of all electricmotorizedslides. These different positionscanbe set byshifting of removing the pin, dependingon the positionby the suspension bracket.

  10. * Place the bottom guide base (G0013003) on the bottom rail of the slide using the positioning jig. Fasten it with an A2 stainless steel M 3.9 x 19 DIN 7504-O self-drilling screw with PH 2 drive. Do this for both sides of the slide.

  11. * Alternatively, fixtures and fittings can be fixed without using jigs as is the case, for example, with the Telescopic/Matic configuration, where the suspension brackets, for the slide engaged, are offset by 6 mm from the center. Please refer at all times to the prescribed dimensions.

  12. CE label • Put the CE-labelon a visible spot, forexampleon the side of the frame (do not put itonthe blades) • Makesure the label fits goodon the frame.

More Related