1 / 28

Legacy-GW Features

This document provides an overview of Legacy-GW features, installation guidelines, and conditions for use. It covers the use of NCP/TDE cards, stacking connections, optional cards, CO and EXT limitations, and more.

wilmat
Download Presentation

Legacy-GW Features

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Legacy-GW Features Rev1.4 24 Jan., 2013

  2. Over view

  3. Over view 1.Use NCP/TDE（TDA）as a legacy GW by stacking connection with NS1000. 2.NCP/TDE(TDA) connect with NS by stacking card working as part of One-look network.

  4. Over view Introduce new card ; STACK-M (for NS), STACK-S (1 for NCP/ 1 for TDE) STACK-M card Slave Units Site #1 NS1000 as stacking Master Unit Site #2 Master for One-look Site #3 Stacking Slave NCP500 NCP1000 LAN Stacking Slave Stacking Slave Site #4 　： 　： Stacking Slave STACK-S card Proprietary cable for stacking connectionThe length of the cable：2M(Dedicate cable for these Stacking card)

  5. Over view New card

  6. Condition

  7. Condition 1 1.MPR of NCP has to be removed to install Stack-S card. This means Virtual card on NCP is not supported. All of IP terminal has to connect to NS1000. 2.Type of GW has to be same for each NS1000. Category1: NCP500 /NCP1000 Category2: TDE100/200, TDA100/200 Category3: TDE600/620, TDA600/620 3.Max 2 GW for each NS. Max 8 for entire One-look network. 4.TDA15/30/50/100D is not supported. 5. AK is not required to use Legacy GW. STACK-M card Stacking Slave #1 Stacking Slave #2 *If the type of cabinet is mixed then 2nd one will not be worked. STACK-S card

  8. Condition 2 In case of TDE600 each cabinetcount as 1 GW and connection to NS has to be done by Stack-S card. Bus card in TDE600 and TDE620 has to be removed. NS1000 NS1000 NS1000 TDE620 TDE620 TDE600 TDE600 TDE620 TDE600 OR OR

  9. Condition 3 Which Optional card can not be used at Legacy GW? Basically Optional card 1)on TDE/NCP MPR 2)Support by V5 or later 3) IP-GW, IP-EXT 4) MSG are not supported.

  10. Condition 4 How many CO can be installed in each Legacy GW?

  11. Condition 5 How many EXT can be installed in each Legacy GW?

  12. Condition 6 How many other devices can be installed in each Legacy GW? *2 The maximum number of Air Sync Groups is 16. An Air Sync Group can contain up to 16 IP-CSs. *3 The maximum number of Air Sync Groups is 8. An Air Sync Group can contain up to 32 SIP-CSs.

  13. Condition 7 • AK on NCP/TDE can’t be transferred to NS MPR. • In case of TDA100/200 and TDE100/200 • OPB3 card with ECHO16 must be installed in only SLOT1.- Other than OPB3 card allows to install in any SLOT.- OPB3 card with sub-card except for ECHO16 allows installing in any SLOT. • HGT100, NT400 can’t be connected to NS MPR.

  14. How to work?

  15. How to work? Installation • Both Stack-M and Stack-S card is non hot swappable. • Each cabinet can be power on without any order. • Initial Legacy-GW installation, all card will be initialized. • The optional service cards is hot swappable. • TVM can be installed as VM system for entire One-look. • CS can be installed at both NS(NCP0158) and Legacy-GW • (TDA0141/142/155/156/158). PS can Hand over between • these CS to CS(NCP0158, TDA0141/142/155/156/158).

  16. How to work? Wireless • Hand over between NS to Legacy GW and Legacy GW to • Legacy GW is available. LAN IP-CS(NCP0158) IP-CS CS(TDA0141/142/155/156/158) CS PS CS CS • If Legacy CS and IPCS are mixed then all CS must be assign under Air sync group 1.

  17. How to work? Start up LED Status “Stack-M” LED Green On : Normal working condition Off: Error( Not Working) “Stack-S” LED Green On : INS Red On : Fault Red Flash: OUS Legacy GW “RUN” LED Green Off :Power off On : Running as GW Slow Flash: While start up “ALARM” LED Red Off : No present error On : Present Error

  18. How to work? Maintenance • All below service for Legacy-GW is supported through NS1000 cabinet. • Programming • Firmware update • Error log, Syslog • SNMP information • SMDR

  19. Programming

  20. Programming Programming at NS1000 Button to switch Physical-Virtual-LegacyGW1-LegacyGW2 Stack S connect to “1” on Stack M consider as “GW1” Each Optional Card can be selected and installed.

  21. Programming Programming at NS1000 LPR Software :Software can be download through NS1000 LPR Software name same as existing models LPR Software for STACK-S card “PSTKS” is new!

  22. Programming Programming at NS1000 Programming items related to Legacy GW support. Related to VM. Related to DSS. Port Property

  23. Appendix

  24. Appendix Supported optional card

  25. Appendix Supported optional card

  26. Appendix Supported optional card

  27. END

  28. Modification 20120827-01LegacyGW_Rev1_27Aug2012Mar.ppt - 1st release 20120905-02 LegacyGW_Rev1_1_5Sep2012Mar.ppt - Edit slide #11 revise number of legacy EXT and DPT. - Add slide #12 20121031-03 LegacyGW_Rev1_2_31Oct2012Mar.ppt - Add comment for slide #7 “No AK required” - Add additional sample for slide #8 - Add comment for slide #9 “Basic idea” - Add comment for #13 about HGT100 and NT400 - Add remark for #16 20121108-04 LegacyGW_Rev1_3_8Nov2012Mar.ppt - correct slide #8 600-620 twice to 600-620 and 620-620 20130124-05 LegacyGW_Rev1_4_24Jan2013Mar.ppt - correct slide #10 BRI and LCOT capacity for NCP500 as Legacy GW

More Related