1 / 38

Caterpillar Cat 12H NA Motor Grader (Prefix 4XM) Service Repair Manual (4XM00001 and up)

To get the complete manual, please open the home page website.<br><br>https://www.aservicemanualpdf.com/

yhuhnykm8ukm
Download Presentation

Caterpillar Cat 12H NA Motor Grader (Prefix 4XM) Service Repair Manual (4XM00001 and up)

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Service Repair Manual Models 12H NA M OTOR GRADER

  2. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SEB... 1/35 Shutdown SIS Previous Screen Product: MOTOR GRADER Model: 12H NA MOTOR GRADER 4XM Configuration: 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine Disassembly and Assembly 12H, 140H and 160H Motor Graders Power Train Media Number -SENR8548-14 Publication Date -01/10/2011 Date Updated -12/10/2011 i05303122 Transmission - Assemble SMCS - 3030-016 Assembly Procedure Table 1 Required Tools Tool Part Number Part Description Qty A 5P-9736 Link Bracket 1 B 154-6181 Forcing Screw 2 C 6V-5221 Bolt 1 D 4C-8156 Lifting Fixture 1 E 6V-3918 Bolt 1 F 4C-8157 Lifting Fixture 2 G 1U-6405 Three Jaw Puller 1 H 1U-6341 Threaded Rod 1 J 5P-7970 Nut 1 K 9U-7479 Compressing Tube 1 L 5B-0637 High Idle Nut 1 5F-7353 Washer 1 1B-4207 Full Nut 2 5F-7369 Puller Leg 2 3H-0465 Push-Puller Plate 2 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  3. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SEB... 2/35 5F-7366 Forcing Screw 1 5P-4808 Cap 2 1U-9895 Crossblock 1 9S-9151 Block 2 M 1B-4206 Nut 4 8B-7552 Forcing Bolt 2 N 1U-6343 Threaded Rod 1 P 6V-8149 Nut 1 Q 2P-8312 Retaining Ring Pliers 1 1P-2326 Forcing Screw 1 1P-2325 Head 1 R 3H-0462 Bolt 4 8H-0709 Strap 4 5F-7373 Jaw 3 S 3E-3882 Eyebolt 1 T 6V-5765 Sealant 1 Note: Remove old anaerobic sealant from the bottom of the blind tapped holes in housing (11) before assembling. Illustration 1 g00623302 1. Lower the temperature of bearing outer races (130) . Install bearing outer races (130) to the original locations in both transmission case assembly (3) (not shown) and the transmission cover assembly (11) until bearing outer races (130) are seated. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  4. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SEB... 3/35 Illustration 2 g00623301 2. Install bearing retainer (128) on gear assembly (126) . 3. Heat ball bearing (127) to a maximum of 135 °C (275 °F). Install ball bearing (127) to the original location on gear assembly (126) . 4. Use Tooling (Q) in order to install snap ring (129) to the original location on gear assembly (126) . Illustration 3 g00623300 5. Install gear assembly (126) to the original location in the transmission cover assembly (11) . 6. Install two bolts (not shown) on the gear assembly (126) . 7. Install four bolts (125) in the gear assembly (126) . Tighten bolts (125) to a torque of 28 ± 7 N·m (21 ± 5 lb ft). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  5. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SEB... 4/35 Illustration 4 g00623299 8. Install the cup plug (not shown) in input shaft assembly (65) . 9. Install gear (124) on Input shaft assembly (65) . 10. Heat inner bearing (123) to a maximum of 135 °C (275 °F). Install inner bearing (123) on Input shaft assembly (65) until inner bearing (123) is seated. Gear (124) should be tight on input shaft assembly (65) . 11. Install two seal rings (122) to the original locations on Input shaft assembly (65) . Illustration 5 g01024466 12. Install Tooling (S) to Input shaft assembly (65) . Use a hoist in order to position Input shaft assembly (65) to the original location in the transmission case assembly (11) . Install Input shaft assembly (65) in the transmission case assembly (11) . Remove Tooling (S) from Input shaft assembly (65) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  6. https://www.aservicemanualpdf.com/ My Dear Friend! Thank you very much for visiting. Full manual if required, please enter the following URL into your browser. https://www.aservicemanualpdf.com/

  7. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SEB... 5/35 Illustration 6 g00623297 Illustration 7 g00623294 13. Install seal rings (121) on piston (120) . Install both seal rings (121) with the sealing lips facing toward the small diameter of piston (120) . 14. Place Forward shaft assembly (95) in the modified work bench or on blocks. Apply a light coat of clean hydraulic oil on seal rings (121) . Install piston (120) at the original location on Forward shaft assembly (95) . Slightly rotate piston (120) while the seal is being installed. Ensure that the seal rings (121) are installed properly. 15. Install valve assembly (119) to the original location on Forward shaft assembly (95) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  8. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SEB... 6/35 Illustration 8 g00623292 16. Install six clutch plates (117) and seven friction discs (118) in the original order on hub assembly (115) . The splines on hub assembly (115) must align with the splines on the friction discs (118) . 17. Install spring (116) in the original location on Forward shaft assembly (95) . 18. As one unit, install hub assembly (115) , six clutch plates (117) and seven friction discs (118) to the original location on Forward shaft assembly (95) . Illustration 9 g00623291 19. Use a second person in order to manually compress clutch assembly (113) on spring (116) . 20. Install two half rings (114) in the Forward shaft assembly (95) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  9. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SEB... 7/35 Illustration 10 g00623665 21. Install the washer and thrust disc (112) to the original locations on Forward shaft assembly (95) . Illustration 11 g00623672 22. Install gear assembly (110) on Forward shaft assembly (95) and over clutch assembly (113) . Align the spline teeth on the outer diameter of the clutch plates (117) with the splines on the inside of gear assembly (110) . Ensure that gear assembly (110) is completely down over the clutch assembly (113) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  10. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SEB... 8/35 Illustration 12 g00623673 23. Install roller bearing (111) to the original location on Forward shaft assembly (95) . Illustration 13 g00623736 24. Install two thrust discs (131) and thrust race (132) on Forward shaft assembly (95) . The thrust discs (131) should not spin the thrust race (132) . Illustration 14 g00623738 25. Heat inner bearing (109) to a maximum of 132 °C (270 °F). Install inner bearing (109) on Forward shaft assembly (95) until inner bearing (109) contacts the bearing race. 26. Position Forward shaft assembly (95) , as shown. The weight of Forward shaft assembly (95) is approximately 43 kg (95 lb). Place Forward shaft assembly (95) in the modified work bench or blocks. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  11. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SEB... 9/35 Illustration 15 g00623287 27. Install lip seals (108) in piston (107) . Install lip seals (108) with the sealing lip toward the small diameter of piston (107) . 28. Apply a light coat of clean hydraulic oil on lip seals (108) . Illustration 16 g00623285 29. Install piston (107) to the original location on Forward shaft assembly (95) . Rotate the piston slightly while the seal is being installed. Ensure that the lip seals are installed properly. 30. Install valve assembly (106) to the original location on Forward shaft assembly (95) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  12. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 10/35 Illustration 17 g00623284 Note: Friction discs 1 and 7 are different from the remaining discs. Assemble friction discs (1) and (7) with the grooved pattern toward the center of the clutch pack. 31. Install six clutch plates (105) and seven friction discs (103) in the original order on hub assembly (102) . The splines on hub assembly (102) must align with the splines on the friction plates. 32. Install spring (104) to the original location on Forward shaft assembly (95) . 33. As one unit, install hub assembly (102) , six clutch plates (105) , and seven friction discs (103) to the original location on Forward shaft assembly (95) . Illustration 18 g00623281 34. Use two people to manually compress hub assembly (100) on spring (94) . Install two half rings (101) in Forward shaft assembly (95) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  13. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 11/35 Illustration 19 g00623746 35. Install thrust disc and washer (99) on Forward shaft assembly (95) . The thrust disc should not spin the washer. Illustration 20 g00623747 Illustration 21 g00634016 36. Install gear assembly (97) on Forward shaft assembly (95) and over clutch assembly (100) . Align the spline teeth on the outer diameter of the clutch plates with the splines on the https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  14. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 12/35 inside of gear assembly (97) . Ensure that the gear assembly (97) is completely down over hub assembly (102) . 37. Install roller bearing (98) to the original location on Forward shaft assembly (95) . 38. Install the two thrust discs on Forward shaft assembly (95) . Illustration 22 g00623756 39. Heat bearing (96) to a maximum of 132 °C (270 °F). Install bearing (96) on Forward shaft assembly (95) until bearing (96) contacts the bearing race. Illustration 23 g01024454 40. Install Tooling (S) in Forward shaft assembly (95) . Install Forward shaft assembly (95) to the original location in the transmission cover assembly (11) . The weight of Forward shaft assembly (95) is approximately 63.6 kg (140 lb). Remove Tooling (S) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  15. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 13/35 Illustration 24 g00623276 41. Install the cup plug (not shown) from Reverse/Second shaft assembly (68) . 42. Install seals (93) and (94) with the sealing lip toward the small diameter of piston (92) . Illustration 25 g00623270 43. Place Reverse/Second shaft assembly (68) in the modified work bench, or on blocks. Apply a light coat of clean hydraulic oil on the lip seals. Install piston (92) to the original location on Reverse/Second shaft assembly (68) . Rotate the piston slightly while the seal is being installed. Ensure that the lip seals are installed properly. 44. Install valve assembly (91) to the original location on Reverse/Second shaft assembly (68) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  16. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 14/35 Illustration 26 g00623269 45. Install six clutch plates (88) and seven friction disc (90) in the original order on hub assembly (87) . The splines on the hub assembly (87) must align with the splines on the friction discs (90) . 46. Install spring (89) in the original location on Reverse/Second shaft assembly (68) . 47. As one unit, install hub assembly (87) , six clutch plates (88) , and seven friction discs (90) to the original location on Reverse/Second shaft assembly (68) . Illustration 27 g00623265 48. Use two people to manually compress clutch plate (85) on spring (89) . Install two half rings (86) in Reverse/Second shaft assembly. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  17. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 15/35 Illustration 28 g00623760 49. Install the washer and thrust disc (84) to the original locations on Reverse/Second shaft assembly (68) . The thrust disc should not spin the washer. 50. Install gear assembly (82) on Reverse/Second shaft assembly (68) . Align the spline teeth on the outer diameter of the clutch plates with the splines on the inside of gear assembly (82) . Ensure that the gear assembly (82) is completely down over the clutch assembly (85) . Illustration 29 g00634018 51. Install roller bearing (83) to the original location on Reverse/Second shaft assembly (68) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  18. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 16/35 Illustration 30 g00634020 52. Install two thrust discs and one thrust race (133) . Illustration 31 g00634021 53. Heat inner bearing (81) to a maximum of 132 °C (270 °F). Install inner bearing (81) on Reverse/Second shaft assembly (68) until inner bearing (81) contacts the bearing race. The thrust disc should not spin. Illustration 32 g00623260 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  19. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 17/35 Illustration 33 g00623261 54. Position Reverse/Second shaft assembly (68) , as shown. The weight of Reverse/Second shaft assembly (68) is approximately 41 kg (90 lb). Place Reverse/Second shaft assembly (68) in the modified work bench or on blocks. 55. Apply a light coat of clean hydraulic oil on the lip seals. Install lip seals (79) and (80) in piston (78) . Install lip seals (79) and (80) with the sealing lip toward the small diameter of the piston (78) . Rotate the piston slightly while the seal is being installed. 56. Install piston (78) to the original location on Reverse/Second shaft assembly (68) . Ensure that the lip seals are installed properly. 57. Install wave spring (77) on Reverse/Second shaft assembly (68) . Illustration 34 g00623259 58. Install clutch assembly (74) on Reverse/Second shaft assembly (68) . Position the three clutch plates, the four friction disc, and the hub assembly in the original locations on Reverse/Second shaft assembly (68) . 59. Install Tooling (K) and Tooling (H) on Reverse/Second shaft assembly (68) . Tighten Tooling (J) on Tooling (H) in order to compress clutch assembly (74) . Install two half rings (75) and two lock rings (76) in Reverse/Second shaft assembly (68) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  20. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 18/35 60. Carefully loosen Tooling (J) on Tooling (H) in order to relieve pressure from clutch assembly (74) . Remove Tooling (H) and Tooling (K) from clutch assembly (74) . Illustration 35 g00623258 61. Install the thrust disc and the washer on Reverse/Second shaft assembly (68) . 62. Install the sleeve bearing (not shown) on Reverse/Second shaft assembly (68) . 63. Install gear assembly (73) on Reverse/Second shaft assembly (68) . Align the spline teeth on the outer diameter of the clutch plates with the splines on the inside of gear assembly (73) . Ensure that gear assembly (73) is down over the clutch assembly completely. 64. Install the thrust disc (not shown) and spacer (72) to the original locations on Reverse/Second shaft assembly (68) . Illustration 36 g00623761 65. Install gear (71) on Reverse/Second shaft assembly (68) . 66. Install spacer (70) on Reverse/Second shaft assembly (68) . 67. Heat bearing (69) to a maximum of 132 °C (270 °F). Install bearing (69) on Reverse/Second shaft assembly (68) until bearing (69) contacts spacer (70) . Spacer (70) should not spin. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  21. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 19/35 Illustration 37 g01024451 68. Install Tooling (S) in Reverse/Second shaft assembly (68) . Place Reverse/Second shaft assembly (68) to the original location in the transmission case assembly (11) . The weight of Reverse/Second shaft assembly (68) is approximately 64 kg (141 lb). Remove Tooling (S) . Illustration 38 g00623801 69. Install gear (67) to the original location on Input shaft assembly (65) . 70. Heat inner bearing (66) to a maximum of 132 °C (270 °F). Install inner bearing (66) on Input shaft assembly (65) until inner bearing (66) contacts gear (67) . Gear (67) should be tight on input shaft assembly (65) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  22. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 20/35 Illustration 39 g00623250 71. Install seal extension ring (63) and seal ring (64) on piston (62) . Install seal (63) and seal (64) with the sealing lips toward the small diameter of the piston (62) . Apply a light coat of clean hydraulic oil on the lip seals of piston (62) . Illustration 40 g00623249 72. Place First/Third shaft assembly (14) in the modified work bench, or on blocks. Install piston (62) to the original location on First/Third shaft assembly (14) . Rotate the piston (62) slightly while the seal is being installed. Ensure that the lip seals are installed properly. 73. Install wave spring (61) to the original location on First/Third shaft assembly (14) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  23. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 21/35 Illustration 41 g00623248 74. As you install clutch assembly (58) to First/Third shaft assembly (14) , position the three clutch plates, four friction disc and the hub assembly to the original locations on First/Third shaft assembly (14) . 75. Install Tooling (K) and Tooling (H) on First/Third shaft assembly (14) . Tighten Tooling (J) on Tooling (H) in order to compress clutch assembly (58) . Install two half rings (59) and two lock rings (60) to First/Third shaft assembly (14) . 76. Carefully loosen the nut on Tooling (J) in order to relieve pressure from clutch assembly (58) . Remove Tooling (K) and Tooling (H) . Illustration 42 g00634025 77. Install the washer, the thrust disc, and the bearing sleeve to the original locations on First/Third shaft assembly (14) . 78. Install gear assembly (57) in the original location on First/Third shaft assembly (14) and over clutch assembly (58) . Align the spline teeth on the outer diameter of the clutch plates with the splines on the inside of gear assembly (57) . Ensure that the gear assembly (57) is completely down over clutch assembly (58) . 79. Install the thrust disc that was under gear (56) to the original location on First/Third shaft assembly (14) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  24. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 22/35 80. Install gear (56) to the original location on First/Third shaft assembly (14) . Install the thrust disc that was on top of gear (56) . 81. Heat inner bearing (55) to a maximum of 132 °C (270 °F). Install inner bearing (55) on First/Third shaft assembly (14) until inner bearing (55) contacts gear (56) . The thrust disc that is under inner bearing (55) should not spin. Illustration 43 g00623245 82. Install seal extension ring (53) and seal ring (54) on piston (52) . Install seal extension ring (53) and seal ring (54) with the sealing lips toward the small diameter of the piston (52) . Apply a light coat of hydraulic oil on the lip seals. Illustration 44 g00623242 83. Rotate First/Third shaft assembly (14) in order to assemble the other end. The weight of First/Third shaft assembly (14) is approximately 55 kg (121 lb). Place the First/Third shaft assembly (14) on the modified work bench, or on blocks. Install piston (52) to the original location on First/Third shaft assembly (14) . Rotate the piston slightly while the seal is being installed. Ensure that the lip seals are installed properly. 84. Install wave spring (51) to the original location on First/Third shaft assembly (14) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  25. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 23/35 Illustration 45 g00623241 85. As you install clutch assembly (48) to First/Third shaft assembly (14) , position the five clutch plates, six friction disc and the hub assembly to the original locations on First/Third shaft assembly (14) . 86. Install Tooling (H) and Tooling (K) on First/Third shaft assembly (14) . Tighten Tooling (J) on Tooling (H) in order to compress clutch assembly (48) . Install two half rings (49) and two lock rings (50) on First/Third shaft assembly (14) . 87. Carefully loosen Tooling (J) on Tooling (H) in order to relieve pressure from clutch assembly (48) . Remove Tooling (K) and Tooling (H) . Illustration 46 g00623240 88. Install washer (47) and thrust disc (46) to the original locations on First/Third shaft assembly (14) . 89. Install the sleeve bearing on First/Third shaft assembly (14) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  26. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 24/35 Illustration 47 g00623154 90. Install gear assembly (45) in the original location on First/Third shaft assembly (14) . Install gear assembly (45) on First/Third shaft assembly (14) . Align the spline teeth on the outer diameter of the clutch plates with the splines on the inside of gear assembly (45) . Ensure that the gear assembly (45) is completely down over the clutch assembly. 91. Install thrust disc (44) on First/Third shaft assembly (14) . Illustration 48 g00623802 92. Install gear assembly (43) on First/Third shaft assembly (14) . 93. Install the thrust disc that was under bearing (42) on First/Third shaft assembly (14) . Heat bearing (42) to a maximum of 132 °C (270 °F). Install bearing (42) on First/Third shaft assembly (14) until bearing (42) contacts gear assembly (43) . Thrust disc should not spin. 94. Install Tooling (S) (not shown) in First/Third shaft assembly (14) and place First/Third shaft assembly (14) aside. The weight of First/Third shaft assembly (14) is approximately 89 kg (196 lb). https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  27. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 25/35 Illustration 49 g00623150 Illustration 50 g00623149 95. Install seal ring (40) and seal extension ring (41) on piston (39) . Install seal ring (40) and seal extension ring (41) with the sealing lip toward the small diameter of piston (39) . 96. Place High/Low shaft assembly (15) in the modified work bench or on blocks. Apply a light coat of hydraulic oil on the lip seals. Install piston (39) to the original location on High/Low shaft assembly (15) . Ensure that seal ring (40) , and seal extension ring (41) are installed properly. 97. Install 15 springs (38) in the recess pockets in piston (39) . 98. Install one lip seal (37) on balance piston (39) . 99. Install balance piston (35) on High/Low shaft assembly (15) and in piston (39) . Ensure that the guides that are located on balance piston (35) are placed in the center of each spring (38) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  28. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 26/35 Illustration 51 g00623148 100. Install Tooling (K) and Tooling (N) on High/Low shaft assembly (15) and balance piston (35) . Tighten Tooling (P) on Tooling (N) in order to compress balance piston (35) . Rotate balance piston (35) slightly while the seal is being installed. 101. Use Tooling (Q) in order to install retaining ring (36) to High/Low shaft assembly (15) . 102. Carefully loosen Tooling (P) on Tooling (N) in order to relieve pressure from balance piston (35) . Remove Tooling (B) from balance piston (35) and High/Low shaft assembly (15) . Illustration 52 g00623145 https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  29. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 27/35 Illustration 53 g00623141 103. Install the clutch assembly (32) to the original locations on High/Low shaft assembly (15) . The clutch assembly (32) includes seven friction discs, eight clutch plates, and the hub assembly. 104. Install Tooling (K) and Tooling (N) on High/Low shaft assembly (15) and clutch assembly (32) . Tighten Tooling (P) on Tooling (N) in order to compress clutch assembly (32) . 105. Install two lock rings (34) and two half rings (33) to High/Low shaft assembly (15) . 106. Carefully loosen Tooling (P) on Tooling (N) in order to relieve pressure from clutch assembly (32) . Remove Tool (K) and Tooling (N) from High/Low shaft assembly (15) and clutch assembly (32) . 107. Install thrust disc and washer (31) to the original locations on High/Low shaft assembly (15) . Illustration 54 g00623805 108. Install gear assembly (30) in the original location on High/Low shaft assembly (15) . Install gear assembly (30) on High/Low shaft assembly (15) . Align the spline teeth on the outer diameter of the clutch plates with the splines on the inside of gear assembly (30) . Ensure that gear assembly (30) is completely down over clutch assembly. 109. Install two thrust discs (29) and the two bearing sleeves on High/Low shaft assembly (15) . 110. Heat inner bearing (28) to a maximum of 132 °C (270 °F). Install inner bearing (28) on the High/Low shaft assembly (15) until the inner bearing (28) contacts the thrust disc. 111. The thrust disc (29) should not spin. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  30. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 28/35 Illustration 55 g00623134 Illustration 56 g00623132 112. Install seal extension ring (27) and seal ring (26) on piston (24) . Install seal extension ring (27) and seal ring (26) with the sealing lips toward the small diameter of the piston (24) . Apply a light coat of hydraulic oil on seal extension ring (27) and seal ring (26) . 113. Position High/Low shaft assembly (15) , as shown. The weight of the High/Low shaft assembly (15) is 50 kg (110 lb). Place High/Low shaft assembly (15) on the modified work bench, or on blocks. Install piston (24) to the original location on High/Low shaft assembly (15) . Rotate the piston (24) slightly while the seal is being installed. Ensure that the seal extension ring (27) and seal ring (26) are installed properly. 114. Install wave spring (25) to the original location on High/Low shaft assembly (15) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  31. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 29/35 Illustration 57 g00623131 115. As you install clutch assembly (21) to High/Low shaft assembly (15) , position the five clutch plates, six friction discs, and the hub assembly to the original locations on High/Low shaft assembly (15) . 116. Install Tooling (K) and Tooling (H) on High/Low shaft assembly (15) and clutch assembly (21) . Tighten Tooling (J) on Tooling (H) in order to compress clutch assembly (21) . 117. Install two half rings (22) and two lock rings (23) to High/Low shaft assembly (15) . 118. Carefully loosen Tooling (J) on Tooling (H) in order to relieve pressure from clutch assembly (21) . Remove Tooling (H) and Tooling (K) from High/Low shaft assembly (15) and clutch assembly (21) . Illustration 58 g00623129 119. Install the thrust disc, the two sleeve bearings and washer (20) to the original locations on High/Low shaft assembly (15) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  32. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 30/35 Illustration 59 g00623806 Illustration 60 g00623126 120. Install gear assembly (18) , align the internal spline of the cylinder welded to the external teeth of the clutch. Ensure that gear assembly (18) is completely down over clutch assembly (23) . 121. Install thrust disc (19) that was under rotor (17) to High/Low shaft assembly (15) . Heat rotor (17) to a maximum of 135 °C (275 °F). Install rotor (17) to High/Low shaft assembly (15) until rotor (17) makes contact with the shoulder of shaft assembly (15) . Ensure that rotor (17) is completely down against the shoulder of shaft assembly (15) . Thrust disc (19) should spin freely. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  33. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 31/35 Illustration 61 g00623807 122. Heat bearing (16) to a maximum of 135 °C (275 °F). Install bearing (16) to High/Low shaft assembly (15) until bearing (16) makes contact with rotor (17) . Illustration 62 g00634111 123. Install Tooling (F) in High/Low shaft assembly (15) and place High/Low shaft assembly (15) next to First/Third shaft assembly (14) and in Tooling (F) . The weight of High/Low shaft assembly (15) is approximately 89 kg (195 lb). The use of Tooling (F) will hold First/Third shaft assembly (14) and High/Low shaft assembly (15) to the proper height of the gear mesh. This will allow Tooling (D) to be installed properly. Slide the two shafts together until the gear mesh is obtained. https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  34. GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/ Thank you very much for your reading. Please Click Here. Then Get COMPLETE MANUAL. NO WAITING NOTE: If there is no response to click on the link above, please download the PDF document first and then click on it. GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/

  35. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 32/35 Illustration 63 g00849491 124. Use Tooling (C) and Tooling (E) to install Tooling (D) on First/Third shaft assembly (14) and High/Low shaft assembly (15) . First/Third shaft assembly (14) and High/Low shaft assembly (15) must be installed in the transmission cover assembly (11) together. 125. Attach a suitable lifting device to Tooling (D) . Carefully install First/Third shaft assembly (14) and High/Low shaft assembly (15) to the original locations in the transmission case assembly. The weight of the two shaft assemblies is 177 kg (390 lb). Illustration 64 g00623113 126. Position tube assembly (13) and the O-ring (not shown) to the original locations in the transmission case assembly. Install three bolts (12) to secure tube assembly (13) to the transmission case assembly. Tighten bolts (12) to a torque of 55 ± 10 N·m (40 ± 7 lb ft). 127. Clean the flanges of both halves of the transmission cover assembly (11) and the transmission case assembly (3) . Apply a 3.0 mm (0.12 inch) bead of Tooling (T) to the joint between transmission case assembly (3) and transmission cover assembly (11) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  36. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 33/35 Illustration 65 g00623110 Note: Remove Tooling (B) from transmission cover assembly (11) . 128. Attach Tooling (A) and a suitable lifting device to the transmission cover assembly (11) . Carefully install the transmission cover assembly (11) to the transmission case assembly (3) . Be careful not to bind on the locating pins during the installation. Illustration 66 g00623108 129. Install spring pin (10) in seal carrier (5) . 130. Install three seal rings (9) on seal carrier (5) . 131. Install O-ring seals (8) in seal carriers (5) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  37. 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE... 34/35 Illustration 67 g00623105 Illustration 68 g00636998 132. Install Tooling (A) (not shown) in seal carrier (5) . Carefully install seal carrier (5) in the original transmission case assembly bore (7) . Ensure that spring pin (10) is installed in the proper location in the shaft assembly. 133. Install two bolts (6) to secure seal carrier (5) to the shaft assembly. Tighten bolts (6) to a torque of 55 ± 10 N·m (41 ± 7 lb ft). 134. Repeat Steps 132 and 133 in order to install the remaining three seal carriers to the original locations in the transmission case assembly (11) . https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis... 2021/1/23

  38. https://www.aservicemanualpdf.com/ My Dear Friend! Thank you very much for visiting. Full manual if required, please enter the following URL into your browser. https://www.aservicemanualpdf.com/

More Related