1 / 48

POLICY & PROCEDURE

NCPWB WELDER PERFORMANCE QUALIFICATIONS. POLICY & PROCEDURE. NATIONAL CERTIFIED PIPE WELDING BUREAU “TESTING EVENT” POLICY & PROCEDURE “TRAINING PROGRAM”. NCPWB POLICY & PROCEDURE A tutorial for the Contractor when participating in a Joint Welder

zena
Download Presentation

POLICY & PROCEDURE

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. NCPWB WELDER PERFORMANCE QUALIFICATIONS POLICY & PROCEDURE

  2. NATIONAL CERTIFIED PIPE WELDING BUREAU “TESTING EVENT” POLICY & PROCEDURE “TRAINING PROGRAM”

  3. NCPWB POLICY & PROCEDURE A tutorial for the Contractor when participating in a Joint Welder Qualification testing event with the United Association Welder Certification Program

  4. As the NCPWB member contractor present during United Association welder/brazer qualification testing, you are satisfying the requirements in ASME Section IX, Para. QW-300.2 and QB-300.2, which states in part that “…welders/brazers or welding operators/brazing operators…shall be tested under the full supervision and control of the manufacturer, contractor, assembler or installer…”

  5. The NCPWB Technical Committee has recommended and the NCPWB Board of Trustees has approved the following to be followed by the participating contractor.

  6. NCPWB WELDER PERFORMANCE QUALIFICATIONS IN-PROCESS RESPONSIBILITIES SECTION – I.

  7. I. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING A TESTING EVENT Whenever a welder/brazer is tested, there shall be a NCPWB member contractor present in the facility where the test coupon will be welded/brazed. This person shall be a regular paid employee of a NCPWB contractor. This contractor shall work together with the UA Authorized Testing Representative (ATR) in administering the test.

  8. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING TESTING The following tasks shall be performed by the contractor in coordination with the UA Authorized Testing Representative (ATR) prior to and during the welding/brazing of the test coupon/coupons:

  9. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING TESTING 1.) Verify the identity of the welder/brazer using the picture I.D. and other documentation the welder/brazer has provided to the ATR during the joint test session briefing and roll call.

  10. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING TESTING 2.) Verify that the welder/brazer has access to a copy of the applicable Welding/Brazing Procedure Test Specification (WPS) (BPS) that the welder/brazer will follow during welding/brazing of the test coupon.

  11. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING TESTING 3.) Verify that the welder/brazer has access to a copy of the applicable UA Testing Event Inspection Report. This document covers the in-process inspection hold points, locator stamp, tack welds, start and finish times and requires signatures of both the participating contractor and the ATR.

  12. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING TESTING 4.) Verify the test assembly used during the performance qualification matches the base metal specification #, pipe diameter and desired wall thickness found in the: UA Weld Test Specification, under Pipe Coupon Material.

  13. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING TESTING 5.) Verify that the test coupon is marked with a T-Stamp at 12 o'clock as a position locater, indicating any rotation of the coupon during the testing event. Verify that the coupon remains in the proper fixed position or positions during the entire test with no adjustments to height, angle, or swing.

  14. A LOCATION MARKER OR “T” STAMP AT 12 O’CLOCK

  15. TEST ASSEMBLY IDENTIFICATION NUMBER 6.) Verify that the test coupon is marked with the welder’s/brazer’s test assembly I.D. number. e.g., 63CS4567 63 = UA Test CS = First & Last initials 4567 = Last four of UA ID#

  16. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING TESTING 7.) Verify that the electrode or filler metal type to be used for the root and fill passes are correct and are used in proper sequence in accordance with the UA Weld Test Specification.

  17. SMAW----- PRINTED -------GTAW STAMPED

  18. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING TESTING 8.) Verify with the UA Weld Test Specification that the direction of weldprogression is correct. Verify with the UA Weld Test Specification that the coupon is in the correct test position. e.g., 1-G, 2-G, 5-G, or 6-G

  19. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING TESTING 9.) Verify with the UA Weld Test Specification that the selected amperage is within ranges specified by the WPS. Wire feed speed, voltage, polarity and current can also be verified on this specification document.

  20. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING TESTING 10.) Verify approximate thickness of the weld metal deposited with each process and filler metal type when more than one process or filler metal type is used. Deposited weld metal ranges may be found on the UA Weld Test Specification or Welder Qualification Record.

  21. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING TESTING 11.) Verify proper backing gas and flow rates; torch and weld head gas and their proper mixtures, including flow rate ranges, can also be found on the UA Weld Test Specification sheet.

  22. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING TESTING 12.) The cover pass must be left in the “as welded” condition, cleaning with power or hand wire brush is allowed, (grinding or filing on the completed test coupon inside or outside is not allowed). Per UA Weld Test Specifications

  23. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING TESTING 13.) Safety Check: a continuous safety check for required Personal Protective Equipment is critical. The testing area shall have Adequate Ventilation and be protected from the elements.

  24. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING TESTING 14.) “If at anytime during a weld test the ATR or Contractor Representative determines the welder does not demonstrate the necessary welding skills the weld test shall be terminated.”

  25. NCPWB WELDER/BRAZER PERFORMANCE QUALIFICATIONS CONDUCTING VISUAL EXAMINATIONS SECTION – II.

  26. II. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING A TESTING EVENT After the welder has completed welding any portion of the test coupon and has called for inspection, the Contractor and the UA Authorized Testing Representative (ATR) shall Visually Examine the entire test coupon inside and outside for the following:

  27. Undercut (not to exceed 1/32”) and Overlap / Cold Lap (none permitted)

  28. Incomplete Fusion (none permitted) a.) in the root. b.) in the side wall. c.) on the cover pass.

  29. Root Concavity / Suck Back (none permitted)

  30. Underfill and Incomplete Joint Penetration (none permitted)

  31. Cracks (none permitted)

  32. Porosity (none permitted)

  33. Slag (none permitted) Trapped / Included

  34. Weld Reinforcement “per UA Weld Test Specifications”

  35. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING TESTING “If at anytime during a weld test the ATR or Contractor Representative determines the welder does not demonstrate the necessary welding skills the weld test shall be terminated.”

  36. NCPWB WELDER/BRAZER PERFORMANCE QUALIFICATIONS CONTINUITY UPDATES SECTION – III.

  37. III. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING CONTINUITY UPDATES ASME SECTION IX – QW-322.1a “When a welder or welding operator has not welded with a process during a period of six months or more, his qualifications for that process shall expire.”

  38. III. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING CONTINUITY UPDATES ASME SECTION IX – QW-322.1(1) “when the welder has welded with that process under the supervision and control of the qualifying manufacturer or contractor or participating organization that will extend his qualifications for an additional 6 months.”

  39. WELDER QUALIFICATION CONTINUITY UPDATES UA WCP Quality System Manual: “when unable to maintain continuity from an Employing Manufacturer/Contractor, continuity updates may take place at any UA Authorized Testing Facility and must be supervised by an ATR and at least one Manufacturer / Contractor Representative.”

  40. WELDER QUALIFICATION CONTINUITY UPDATES UA WCP Quality System Manual: “the continuity demonstration shall consist of welding a minimum of one complete pass for each welding process they are qualified in, using a pipe coupon, in accordance with a UA Weld Test Specification applicable to the welding process involved.”

  41. WELDER QUALIFICATION CONTINUITY UPDATES UA WCP Quality System Manual: “the continuity report lists the Welder’s name, last date each welding process was demonstrated by the individual and is signed and dated by the supervising Representative of the Employing Manufacturer/Contractor.”

  42. CONTRACTOR’S & ATR’S RESPONSIBILITIES DURING TESTING “If at anytime during a continuity update the ATR or Contractor Representative determines the welder does not demonstrate the necessary welding skills the continuity update shall be terminated.”

  43. NCPWB WELDER/BRAZER PERFORMANCE QUALIFICATIONS THE END QUESTIONS & ANSWERS

More Related