1 / 28

TR6850 系统介绍

TR6850 系统介绍. TR-6850 测试系统是针对电源管理和混合信号的集成电路测试所特别设计。 最多可达 256 个数字通道，测试速度 33MHz,8M 的 pattern 深度。 专属运放电路测试模组。 16 位元任意波形产生器 / 波形数位器。 能符合多元产品测试需求。 结合微软 Visual Studio.NET 开发工具以 C++ 语言开发测试程式，并提供丰富的除错与分机工具。. System Architecture. Up to 8-Site Parallel Testing Cable Out

zuriel
Download Presentation

TR6850 系统介绍

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. TR6850系统介绍 • TR-6850测试系统是针对电源管理和混合信号的集成电路测试所特别设计。 • 最多可达256个数字通道，测试速度33MHz,8M的pattern深度。 • 专属运放电路测试模组。 • 16位元任意波形产生器/波形数位器。 • 能符合多元产品测试需求。 • 结合微软Visual Studio.NET开发工具以C++语言开发测试程式，并提供丰富的除错与分机工具。

  2. System Architecture • Up to 8-Site Parallel Testing • Cable Out • Maximum 256 Logic I/O Channels • High Precision Measurement Unit • Arbitrary Waveform Generator • Digitizer • Low Cost Mixed Signal Tester

  3. System Architecture • Test Head Architecture PC Interface Digital Module Analog Module

  4. Targeted Applications • For Digital, Analog and Mixed Signal Device • MCU , Interface / Driver … Digital Chip • AD Converter , DA converter • Voltage Comparator • Operational Amplifier • Regulator – Shunt/Voltage Regulator, LDO…

  5. Targeted Applications • Hall Sensor • PWM Switching , PWM Controller • Power Factor Control IC • DC to DC converter • Detector, Voltage Detection • MOSFET • - - - -

  6. Electrical Specifications AC64/AC32 – 64 /32I/O Channels Board Pin Configuration( I/O Channel) : 64/32pins Parametric Measurement Unit : 4 Sets ( 8-pin share) Pin Level Source : Per pin level set Driver Voltage Range : -2.0V to +8V Comparator Voltage Range : -2.0V to +8V Min. Pulse Width : 10ns Micro Instruction : CALL, MATCH,MPAT,MLEN RPT,LOOP,LPEND,STOP,TS

  7. Electrical Specifications • AC64/32 – 64/32 I/O Channels Board – continue • Min. Period : 30ns ~ 40ms • Period resolution : 10ns • Data Rate : 33MHz •  Timing Generators : 4 edge / Pin • Timing Set : 16 change on the fly • Edge Placement resolution : 2.5ns • Time Measurement Resolution : 10ns

  8. Electrical Specifications • AC64/32 – 64/32 I/O Channels Board – continue • Drive Mode : 0,1,NF,NRZ,RZ,RO,SBC • IO Mode : 0,1,NF • Strobe Mode : Edge/Window •  Pattern Memory Depth : 4M~8M •  Fail Memory Depth : 4K • Pattern Symbol : 0/1//X/Z/L/H

  9. Electrical Specifications • OVC -- Octal V/I Resource Board • Voltage Force and Measure Range：20V ,16V，8V，4V，2V • Voltage Force and Measure Resolution：16 bits • Voltage Force and Measure Accuracy： • 2V ：±(0.01 % of value+0.05 % of range ) • 4V ：±(0.01 % of value+0.05 % of range ) • 8V ：±(0.01 % of value+0.05 % of range ) • 16V ：±(0.01 % of value+0.05 % of range ) • 20V : ±(0.01 % of value+0.05 % of range ) • Voltage clamp Resolution：16 bits • Current Force and Measure Range：1uA，10uA，100uA，1mA， 10mA，100mA，200mA • Current Force and Measure Resolution：16 bits

  10. Electrical Specifications • OVC -- Octal V/I Resource – continue • Current Force and Measure Accuracy： • 1uA ：±(0.2 % of value+0.2 % of range ) • 10uA ：±(0.1 % of value+0.1 % of range ) • 100uA : ±(0.1 % of value+0.1 % of range ) • 1mA : ±(0.1 % of value+0.1 % of range ) • 10mA : ±(0.1 % of value+0.1 % of range ) • 100mA ：±(0.1 % of value+0.1 % of range ) • 200mA : ±(0.1 % of value+0.1 % of range ) • Current Clamp Resolution：16 bits • 10KSPS DDS programmable to any Channel(16 bit) • 10KSPS Digitizer multiplexed to two channels(16 bits) • DVM Differential voltage measure between two channels

  11. Electrical Specifications • PVC -- Pulse Mode V/I Resource • 2 Independent V/I Resource • Floating Ground，Pulse Mode • Programmable Pulse period • Protection Timer • Voltage Force and Measure Range：4V，8V，16V，32V，46V • Voltage Force and Measure Resolution：16 bits • Voltage Force and Measure Accuracy： • 8V ：±(0.3 % of value+0.15 % of range) • 16V ：±(0.3 % of value+0.15 % of range) • 32V ：±(0.3 % of value+0.15 % of range) • 46V ：±(0.3 % of value+0.21 % of range)

  12. Electrical Specifications • PVC -- Pulse Mode V/I Resource – continue • Current Force and Measure Resolution：16 bits • Current Force and Measure Accuracy： • 150mA : ±(0.5% of value+0.25 % of range ) • 300mA : ±(0.5% of value+0.25 % of range ) • 1.5A ：±(0.5% of value+0.25 % of range ) • 3A : ±(0.5% of value+0.25 % of range ) • 5A : ±(0.5% of value+0.25 % of range ) • 10A : ±(0.5% of value+0.25 % of range ) • 15A : ±( 1.0% of value+0.25 % of range ) • 30A : ±( 1.0% of value+0.25 % of range )

  13. Electrical Specifications • DVC -- Full Four-Quadrant V/I Source • Voltage Force and Measure Range：1V, 2V, 4V, 8V,16V, 32V, 48V • Voltage Force and Measure Resolution：16 bits • Voltage Force Accuracy： ± (0.05 % of value+0.05 % of range) • Voltage Measure Accuracy：± (0.03% ofvalue +0.03 % of range) • Current Force and Measure Range：2uA，20uA，200uA， 2mA，200mA, 1A, 2A

  14. Electrical Specifications • DVC -- Full Four-Quadrant V/I Source – continue • Current Force and Measure Resolution：16 bits • Current Force and Measure Accuracy： • 2uA ~ 200uA ：± (0.05 % of value+0.05 % of range +10nA ) • 2mA~ 200mA ：± (0.1 % of value+0.1 % of range) • 1A~2A : ± (0.3 % of value+0.1 % of range) • Differential voltage measure between two channels • Measure Resolution : 16 bit • Measure accuracy: ±(0.2 % of range + 200uV) • 20mV, 100mV, 200mV, 1V, 2V, 4V, 10V, 20 , 100V

  15. Electrical Specifications • Arbitrary Waveform Generator – continue • Pin Counts Per Module：2 • 4 Single-ended or 2 Differential. • Resolution：16 Bits. • Sampling Rate：40M SPS max，625k SPS min • Waveform Memory：4M. • Output Range：±5Vpp@50 ohm load • ±10Vpp@ a high-impedance load • Accuracy : ±0.1dB • DC Offset Range：±2.5V@50 ohm load • Accuracy :±5mV

  16. Electrical Specifications • Arbitrary Waveform Generator - continue • Harmonic products ans spurs : –75 dBc • Output Impedance：50 ohm，75 ohm. • Filter：Analog, 2MHz, 500kHz, 50kHz, 5k, Through. • TTL Rising edge PW：40ns min. • SYNC Output：TTL Duty Cycle：20% to 80%. • Marker Output：TTL 8 Sample clock periods. • Frequency Range：1Hz ~ 1MHz

  17. Electrical Specifications • Digitizer • Input -3dB Freq. : 1Mhz • 16bits (Low Speed: 500Ksps)/ 14bits (High Speed 10Msps) • 4 single or 4 differential-end channels Output: 10Vpp @ 50 ohm Load to GND • MEM Depth: 4M*16bits/channel • Anti-Filter: 20kHz, 200kHz, 2Mhz • Notch Filter: Notch freq. ~1Khz for audio testing. • Digital Filter: 2x, 4x, 8x, 16x, 32x, 64x decimation filter. • User Offset: ±2.0V • Input Impedance: 50ohm, 1Mhz common ground or 100ohm, 10kohm differential.

  18. Electrical Specifications • Digitizer - continue • PGA ranges: • Single ended: ±0.1, ±0.5, ±1, ±2, ±5, ±10 • Differential: ±0.05, ±0.1, ±0.25, ±0.5, ±1, ±2.5, ±5 • Dynamic Performance (1kHz -1dBFS test tone with 2x decimation filter) • THD: < -80dBc • SNR: > 80dBc • THD+N: < -80dBc • Dynamic Performance (1kHz -1dBFS test tone with Notch filter) • THD: -105dBc • SNR: 99dBc • THD+N: -98dBc

  19. Electrical Specifications • TMU -- Time Measure Unit • Positive/Negative Slope. • Counter，Time measurement，Rising/Failing time. • Time Resolution：625ps Propagation delay • Timeout function and Overflow state. • Input waveform：Sine，square，sawtooth. • Low Impedance Inputs : A, B • ±10V Range：Impedance 2K/1M Ohm Nominal • ±2.5V Range ：Impedance 2K/1M Ohm Nominal • Input Threshold Accuracy：0.5% of Range

  20. Electrical Specifications • OP-LOOP Board • Four OP AMP Loop • DC Measurement：16 bits • Common Mode DAC：16 bits • AC Stimulus：16 bits High Speed DAC • AC measurement：12 bit ADC，10MHz Sample Rate • Loop Reference DAC：16 bits • Input Offset voltage (Vos) • Input Offset Current (Ios) • Open loop gain (Avol)

  21. Electrical Specifications • OP-LOOP Board -- continue • Command Mode Rejection Ration (CMRR) • Power Supply Rejection Ration (PSRR) • Gain Bandwidth Product (GBW) • Slew Rate (SR)

  22. Electrical Specifications • KVS board:  • 2 Channels Floating Ground System • 16bit ADC for voltage and current measure • 16 bit DAC for voltage and current force • Vmax: 900V • Imax: 15mA  • Vrange : 100V, 200V, 500V,1000V  accuracy:  ±(0.05% of value + 0.25% of range) • Irange: 15uA, 150uA, 1.5mA, 15mA accuracy:±(0.05% of value + 0.35% of range) • Time Max : 10 sec

  23. Electrical Specifications • QVC board : • Four Independent, Full Four-Quadrant VI’s; • Voltage to ±45V, Current to ±1A • Voltage ranges 1, 2, 4, 8, 16, 32, 45 vlots; • Current ranges 2uA, 20uA, 200uA, 2mA, 20mA, 200mA, 1A; • 16 bits force and measure resolution; • Measure V without forcing;

  24. Electrical Specifications • QVC board : • Voltage Force • Forcing Resolution 16bits • Force Accuracy±(0.05% of value + 0.05% of range) • Voltage Measure • Measure Resolution 16bits • Measure Accuracy±(0.05% of value + 0.05% of range)

  25. Electrical Specifications • QVC board : • Current Force • Forcing Resolution 16bits • 2uA Range Accuracy±(0.1% of value + 0.1% of range + 10nA) • 20uA – 1A Range Accuracy ±(0.1% of value + 0.1% of range) • Current Measure • Measure Resolution 16bits • 2uA Range Accuracy±(0.1% of value + 0.1% of range + 10nA) • 20uA – 1A Range Accuracy ±(0.1% of value + 0.1% of range)

  26. Electrical Specifications • MVC board : • Full Four-Quadrant V/I Channel:2 • Max. Voltage:100V ~ -45V • Max. Current :500mA / 45VRange,100V@200mA • Voltage Ranges100V, 50V, 32V, 16V，8V，4V • Voltage Force Accuracy± (0.05 % of value+0.1 % of range) • Voltage Measure Accuracy± (0.05% of Value +0.1 % of range)

  27. Electrical Specifications • MVC board -continue: • Voltage Clamp Resolution16 bit • Current Range2uA, 20uA, 200uA, 2mA, 20mA, 200mA, 500mA • Current Force Accuracy: • 2uA ~ 200uA ：±(0.1 % of value+0.2 % of range +10nA ) • 2mA~ 200mA ：±(0.1 % of value+0.2 % of range) • 500mA : ±(0.1 % of value+0.2 % of range) • Current Measure Accuracy: • 2uA ~ 200uA ：±(0.1 % of value+0.2 % of range +10nA ) • 2mA~ 200mA ：±(0.1 % of value+0.2 % of range) • 500mA : ±(0.1 % of value+0.2 % of range) • Current Clamp Resoulation16 bit

  28. Electrical Specifications • MFB(8 channel ) • Ramp force accuracy • 4V Range  : 1mV • 12V Range : 2.5mV • Measure accuracy: • 4V range none filter  : 1mV • 10 range none filter : 2.5mV • 4V range with filter : 2.5mV •  10 range with filter : 5mV • AWG sample rate       :  1MHZ  @ 64K length • Digitizer Sample rate  :  250K  @ 64K length • AWG & Digitizer loop back testing : 1KHZ  @3V > 70dB • SDIO function        : Sample Rate 1Mbps • {A,B}, {C,D},{E,F},{G,H} combination for data, clk signal.

More Related