1 / 24

Unit 4 The Performance of Second Order System

Unit 4 The Performance of Second Order System. 中華技術學院電子系 副教授 蔡樸生 副教授 林盈灝. Open Loop & Close Loop. Open Loop :. Close Loop :. The Performance of Second Order System. The Response of Second Order System. Homework 1. 1. Steady State Error :. 2. Overshoot :. 0.163.

Download Presentation

Unit 4 The Performance of Second Order System

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Unit 4 The Performance of Second Order System 中華技術學院電子系 副教授 蔡樸生 副教授 林盈灝

  2. Open Loop & Close Loop Open Loop: Close Loop:

  3. The Performance of Second Order System

  4. The Response of Second Order System

  5. Homework 1 1. Steady State Error : 2. Overshoot : 0.163 3. The Peak Time : 1.8138 s 4. The Rise Time : 0.9 s 5. The Setting Time : 4 s [Hint] : max

  6. The Response of

  7. Homework2 : The effect of damping ratio

  8. P Controller • This type of control action is formally known as proportional control (Gain) • Homework3 : K=1, K=4 , K=8 , K=12 , K=36 • Please explain the effect of P controller to the second order system

  9. Solution of HW3

  10. PD Controller

  11. The Performance of P Controller • : The error signal is positive, the torque is positive and rising rapidly. The large overshoot and oscillations in the output because lack of damping. • : The error signal is negative, the torque is negative and slow down causes the direction of the output to reverse and undershoot. • : The torque is again positive, thus tending to reduce the undershoot, the error amplitude is reduced with each oscillations.

  12. The contributing factors to the high overshoot • The positive correcting torque in the interval is too large (抑制) Decrease the amount of positive torque • The retarding torque in the interval is inadequate (增強) Increase the retarding torque

  13. The Effect of PD Controller • : is negative; this will reduce the original torque due to alone. • : both and is negative; the negative retarding torque will be greater than that with only P controller. • : and have opposite signs. Thus the negative torque that originally contributes to the undershoot is reduced also.

  14. Homework 4

  15. Solution of PD Controller • clear; • x1=0;x2=0;dt=0.01;r=1;step=2000; • kp=36;kd=6;pe=r-x1; • for k=1:step • t(k)=k*dt; • e=r-x1; • de=(e-pe)/dt; • u=kp*e+kd*de; • x1=x2*dt+x1; • x2=(u-4*x2)*dt+x2; • pos(k)=x1;vel(k)=x2;pe=e; • end

  16. PI Controller

  17. HW5 : The Effect of PI Controller • Adds a zero at to the forward-path T.F. • Adds a pole at to the forward-path T.F. • This means that the steady-state error of the original system is improved by one order. a=2,b=8,k=1

  18. Program of PID Controller • clear; • x1=0;x2=0;dt=0.01;r=1;step=2000; • kp=1;kd=6;ki=0.1;pe=r-x1;ie=(r-x1)*dt; • for k=1:step • t(k)=k*dt; • e=r-x1; • de=(e-pe)/dt; • ie=ie+e*dt; • u=kp*e+kd*de+ki*ie; • x1=x2*dt+x1; • x2=(u-2*x2-8*x1)*dt+x2; • pos(k)=x1;vel(k)=x2;pe=e; • end

  19. PID Controller

  20. Homework6針對以下系統, 憑藉經驗值調諧PID三個參數值, 使得系統響應為最佳化

  21. Homework7 : Ziegler-Nichols Tuning Step 1 : Let until the occur of critical stable Step 2 : Optimal Parameter Tuning

  22. Homework8: Pendulum System

  23. Feedback Controller Design State Feedback Controller

More Related