1 / 47

SUBMARINES

Overview (10.1) SUBMARINES 200+ Years Old (Turtle (1775) and Hunley (1864)) Navy mostly uses submarines (indefinite underwater endurance) Commercial industry uses submersibles (limited endurance) Expensive but stealthy!

Patman
Download Presentation

SUBMARINES

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Overview (10.1) SUBMARINES • 200+ Years Old (Turtle (1775) and Hunley (1864)) • Navy mostly uses submarines (indefinite underwater endurance) • Commercial industry uses submersibles (limited endurance) • Expensive but stealthy! • Share characteristics of both surface ships and aircraft CSS Hunley

  2. Submarine Structural Design (10.2) SUBMARINES • Longitudinal Bending - Hogging & sagging causes large compressive and tensile stresses away from neutral axis. A cylinder is a poor bending element. • Hydrostatic Pressure = Major load for subs. Water pressure attempts to implode ship. Transverse frames required to combat loading. A cylinder is a good pressure vessel! • Recall:

  3. Submarine Inner Hull (10.2) SUBMARINES • Holds the pressure sensitive equipment (including the crew!) • Must withstand hydrostatic pressure at ops depth. • Transversely framed with thick plating. • Strength  = $ ,  , space  , but depth  . • Advanced materials needed due to high .

  4. Submarine Outer Hull (10.2) SUBMARINES • Smooth fairing over non-pressure sensitive equipment such as ballast and trim tanks and anchors to improve vessel hydrodynamics. • High strength not required so made of mild steels and fiberglass. • Anechoic (“free from echoes and reverberation”) material on outer hull to decrease sonar signature.

  5. Submarine General Arrangements (10.2) SUBMARINES • Main Ballast Tanks • Variable Ballast Tanks PRESSURE HULL

  6. Main Ballast Tanks (MBT) (10.2) SUBMARINES • Largest tanks. • Alter  from positive buoyancy on surface (empty) to near neutral buoyancy when submerged (full). • Main Ballast Tanks are “soft tanks” because they do not need to withstand submerged hydrostatic pressure. (Located between inner & outer hulls.)

  7. Variable Ballast Tanks (10.2) SUBMARINES • Depth Control Tank (DCT) • Alter buoyancy once submerged. • Compensates for environmental factors (water density changes). • ‘Hard tank’ because it can be pressurized (has access to outside of pressure hull). • Trim Tanks (FTT/ATT) • ‘Soft tanks’ shift water to control trim (internal)

  8. U.S. Submarine Types (10.3) SUBMARINES • Ohio Class • Sub Launched Ballistic Missiles (SLBMs) aft of sail •  greater than many surface ships (i.e. BIG)

  9. U.S. Submarine Types (10.3) SUBMARINES • Los Angeles Class (SSN688)

  10. U.S. Submarine Types (10.3) SUBMARINES

  11. U.S. Submarine Types (10.3) SUBMARINES

  12. U.S. Submarine Types (10.3) SUBMARINES Virginia Class Displacement: 7,800 tons Length: 377 feet Draft: 32 feet Beam: 34 feet Depth: 800+ feet

  13. U.S. Submarine Types (10.3) SUBMARINES USS Dolphin AGSS-555 NR1 L = 165 feet Diesel/Electric 3000 feet depth! L = 145 feet Nuclear 2400 feet depth

  14. Submarine Hydrostatics (10.4) SUBMARINES USS Bremerton (SSN 698)

  15. Submarine Hydrostatics (10.4) SUBMARINES • Static equilibrium and Archimedes Principle apply to subs as well. • Unlike surface ships, subs must actively pursue equilibrium when submerged due to changes in density () and volume (). • Depth Control Tanks & trim tanks are used.

  16. Hydrostatic Challenges (10.4) SUBMARINES • MAINTAIN NEUTRAL BUOYANCY • Salinity Effects • Water Temperature Effects • Depth Effects • MAINTAIN NEUTRAL TRIM AND LIST • Transverse Weight Shifts • Longitudinal Weight Shifts

  17. Hydrostatics (Salinity Effects) (10.4) SUBMARINES Water density ()  as salinity level . • Decreased  = less FB •  sub weight > FB. • Must pump water out of DCT • Changes in salinity common near river estuaries or polar ice. • Mediterranean salinity is higher from evaporation.

  18. Hydrostatics (Temperature Effects) (10.4) SUBMARINES Water density ()  as temperature . • Decreased  = less FB •  sub weight > FB. • Must pump water out of DCT to compensate. • Changes in temperature near river estuaries or ocean currents (Gulf Stream, Kuroshio, etc.)

  19. Hydrostatics (Depth Effects) (10.4) SUBMARINES • As depth increases, sub is “squeezed” and volume () decreases. • Decreased  = less FB •  sub weight > FB. • Must pump water out of DCT • Anechoic tiles cause additional volume loss as they compress more.

  20. Neutral Trim - General (10.4) SUBMARINES • When surfaced, geometric relationships similar except that “G” is below “B” for sub. • Neutral trim on sub becomes extremely critical when submerged. • Note the positions of “G”, “B”, “MT”, and “ML” in the following figures!

  21. Neutral Trim - General (10.4) SUBMARINES • Recall: these relationships can be used in transverse or longitudinal directions to find KMT or KML for a surface ship.

  22. Neutral Trim - General (10.4) SUBMARINES • Surfaced submarine similar to surface ship except G is below B. • For clarity, MT is shown above B although distance is very small in reality.

  23. Neutral Trim - General (10.4) SUBMARINES • When submerging, waterplane disappears, so no second moment of area (I), and therefore no metacentric radius (BML or BMT). • “B”, “MT” and “ML” are coincident and located at the centroid of the underwater volume -the half diameter point (if a cylinder). • Very sensitive to trim since longitudinal and transverse initial stability are the same.

  24. Neutral Trim - General (10.4) SUBMARINES • When completely submerged, the positions of B, MT and ML are in the same place.

  25. Trim & Transverse Weight Shifts (10.4) SUBMARINES • Recall In Surface Ship Analysis: • GMT is found by equation (& Incline Experiment) to calculate the vertical center of gravity, KG. • Equation was only good for small angles () since the metacenter is not stationary at larger angles. • Large  only available from analysis of Curve of Statical Intact Stability.

  26. Trim & Transverse Weight Shifts (10.4) SUBMARINES • Recall for a Surface Vessel:

  27. Trim & Transverse Weight Shifts (10.4) SUBMARINES For a Submarine: (GM is replaced by BG!)

  28. Trim & Transverse Weight Shifts (10.4) SUBMARINES • In Submarine Analysis: • Calculation of heeling angle simplified by identical location of Center of Buoyancy (B) and Metacenter (M). • Analysis involves the triangle G0GTB and a knowledge of the weight shift. • This equation is good for all angles:

  29. Trim & Transverse Weight Shifts (10.4) SUBMARINES • Surface Ship analysis complicated because vessel trims about the center of floatation (F) (which is seldom at amidships). • Sub longitudinal analysis is exactly the same as transverse case. For all angles of trim: • Moment arm l  t, so trim tanks to compensate.

  30. Submarine Stability (10.5) SUBMARINES USS Seawolf SSN-21

  31. Submarine Submerged Intact Stability (10.5) SUBMARINES

  32. Submarine Intact Stability (10.5) SUBMARINES • Initial stability simplified for subs. • The distance BG is constant (=GM) Righting Arm (GZ) is purely a function of heel angle. • EQUATION IS TRUE FOR ALL SUBMERGED SUBS IN ALL CONDITIONS!

  33. Submarine Intact Stability (10.5) SUBMARINES • Since righting arm equation good for all , curve of intact statical stability always a sine curve with a peak value equal to BG.

  34. Submerged Stability Characteristics (10.5) SUBMARINES • Range of Stability: 0-180° • Angle of Max Righting Arm: 90° • Max Righting Arm: Distance BG • Dynamic Stability: 2SBG • STABILITY CURVE HAS THE SAME CHARACTERISTICS FOR ALL SUBS!

  35. Submarine Resistance (10.6) SUBMARINES • Recall Coefficient of Total Hull Resistance • CV = viscous component, depends on Rn. • CW = wave making resistance, depends on Fn. • CA = correlation allowance, surface roughness and “fudge factor”.

  36. Submarine Resistance (10.6) SUBMARINES • On surface (acts like a surface ship): • CV dominates at low speed, CW as speed increases (due to bigger bow and stern waves and wake turbulence). • Submerged (acts like an aircraft): • Skin friction (CF CV) dominates. (Rn is more important when no fluid (air/water) interface). • CW tends toward zero at depth. • Since CT is smaller when submerged, higher speeds are possible.

  37. Submarine Propellers - Odd # of Blades (10.6) SUBMARINES

  38. Skewed Propellers (10.6) SUBMARINES • Advantages: • Reduced Vibration (eases into flow). • Reduced Cavitation. • Disadvantages: • Inefficient backing. • Expensive & difficult to make. • Reduced strength. • Operational need outweighs disadvantages!

  39. Submarine Seakeeping (10.7) SUBMARINES • Subjected to same as surface ships • 3 translation (surge, sway, heave) and 3 rotational (roll, pitch, yaw). • Recall heave, pitch, and roll are simple harmonic motions because of linear restoring force. • If e = resonant freq, amplitudes maximized (particularly roll which is sharply tuned). • Roll motion accentuated by round shape. Why?

  40. Submarine Seakeeping - Suction Force (10.7) SUBMARINES • Water Surface Effect • Submarine near surface (e.g. periscope depth) has low pressure on top surface of hull causing net upward force. • Magnitude depends on speed, depth, and hull shape. • Minimize by reducing speed and having bow down trim. • Wave Action • Top of sub has faster velocity due to similar lower pressure effect as above. • Minimize by going deeper or beam on to waves.

  41. Submarine Maneuvering and Control (10.8) SUBMARINES • Lateral motion controlled with rudder, engines, and props, but also has to control depth. • Depth control accomplished by: • Making the buoyant force equal the submarine displacement as in previous section. • Finer and more positive control achieved by plane (control) surfaces.

  42. Fair-Water Planes (10.8) SUBMARINES • Primarily to maintain an ordered depth. • Positioning the planes to the "up" position causes an upward lift force to be generated. • Since forward of the center of gravity, a moment (M) is also produced which causes some slight pitch. • The dominant effect is the lift generated by the control surface.

  43. Fair-Water Planes (10.8) SUBMARINES • Primarily DEPTH CONTROL

  44. Stern and Bow Planes (10.8) SUBMARINES • Primarily to maintain pitch because of the distance from the center of gravity. • Positioning the planes to creates a lift force in the downward direction creates a moment (M) which causes the submarine to pitch up. • Once the submarine has an up angle, the hull produces an upward lift force. • The net effect is that the submarine rises at an upward angle.

  45. Stern and Bow Planes (10.8) SUBMARINES • Maintain Pitch • (better control than with fairwater planes)

  46. FINAL THOUGHT... SUBMARINES There are times when accurate control is nice!

  47. NAVAL ENGINEERING I Good Luck and Good “Boating”!

More Related