How to Easily Renew Concrete Surface?

1. How How to to Easily R Easily Ren enew Con ew Conc crete rete Su Surfac rface e Once upon a time, the only solution for aging or cracked concrete patio or driveway was to break it up with a sledge hammer or a bulldozer and replace it completely with a new one. But modernization has brought in a lot more alternatives to this extreme method. Polymer based cement formulations or resurfaces are now used to fill in the cracks that appear on the concrete surfaces due to aging. Usually a mix of water, high performance polymer and Portland cement are taken together and applied on these damaged surfaces with the help of steel trowels to squeeze it into the cracks for long time repairing solutions. It can be used on any kind of concrete surface and not just patio or driveways. The mixture that is prepared stays applicable only for 30 mins after combination with water and hence it is a frenetic and tough job to do. B But ut you done. We wi done. We will cl you must must be be wonderin wondering g h how ll clar ari ify t fy th he s e step ow the below: the wh whole ole pr process ocess is is teps s below: 1. of the mixture of high quality polymer along with Portland cement and water is made and squeezed into these gaps. In case of hairline cracks it is squeezed in with a putty knife. But if the crack is larger, then a caulking gun is used to push in the mixture and then it is leveled with the help of a putty knife. Filling in Cracks: Patches and cracks on the concrete surface can easily be covered with the help 2. slabs of concrete which are laid side by side. The gaps between the slabs are left open so than expansion and contraction of the slabs are done smoothly. These gaps are then covered with masking tapes to prevent it from getting filled with cements. Mask Expansion: When the surface is large, then the concrete surface is usually made of large 3. 5-gallon bucket and 20-pound bag of mixture and it is continuously done for two minutes. The paddle is then made to stand in a bucket full of water to wash off the extra concrete. Mixing the Concrete: The concrete is mixed in water by a heavy mixing paddle. This is done in a 4. out with the help of the trowel by pressing it down hard. While one batch is being spread out another batch is being prepared in order for laying down. Spreading of Mixture: This mixture is then spread on the surface of the slabs and quickly spread

2. 5. surface of the mixture that is laid. The medium bristle broom is drawn on the surface with light strokes. Texture of the Surface: Texture of the surfaces can be created by drawing a broom on the wet 6. spread quickly to cover a larger area. This can be done with the help of a long handle squeegee that usually facilitates the drawing of the mixture on a larger surface in a fast-paced manner so that the mixture is spread evenly and it can be pressed hard to cover the uneven surfaces as well. Large Surface Filling: If the filling is being done on a large surface of concrete then it has to be 7. the gaps to reveal the empty spaces. You can use this newly created surface for walking after 2 hours of laying down the mixture. However, you have to wait for at least 6 hours before you can drive a car on it. After 24 hours of laying the mixture on the surface, we have to now cover the surface with a water borne and clear masonry sealer that will protect the whole setup from damages for a long time. Finishing Touch: After you have swept the surface clean, you can now pull of the duct tapes in If you hail from Seattle and are confused as to which method will be most suitable to repair the damaged concrete driveway, you can always fall back on the sound advice of Sound Concrete Co. Sound Concrete Co is one of the most reliable sources when it comes to laying or repairing concrete and they proudly showcase their good quality work via multiple satisfied clients, properly finished and strong concrete works that they provide clients with are value for money. Proudly serving places like Bellevue, Shoreline, Federal Way, Bothell, Issaquah etc. they have been in the business for two decades and have built quite a reputation for their work and have adapted all the modern techniques. Using the ASTM standard for judging their concrete strength and also using stealthfiber to further prevent the appearance of cracks on concrete driveways have been an old practice of Sound Concrete Co. So, what are you still thinking about? Get in touch with Sound Concrete Co now and get the best solution for your damaged concrete surface without replacing it completely. To Get More Details: http://soundconcretecowa.com/