1 / 29

The Status of the CMS Electromagnetic Calorimeter

The Status of the CMS Electromagnetic Calorimeter. R M Brown On behalf of the CMS ECAL Group. Overview. Introduction Design objectives and technology choices Description and status: Crystals Photo-detectors On-detector electronics Off-detector electronics Laser monitoring system

abbott
Download Presentation

The Status of the CMS Electromagnetic Calorimeter

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. The Status of the CMS Electromagnetic Calorimeter R M Brown On behalf of the CMS ECAL Group Elba May 2006 R M Brown - RAL 1

  2. Overview • Introduction • Design objectives and technology choices • Description and status: • Crystals • Photo-detectors • On-detector electronics • Off-detector electronics • Laser monitoring system • Mechanical construction and assembly • Pre-shower • Intercalibration with cosmic muons • Construction and installation schedule • Summary Elba May 2006 R M Brown - RAL 2

  3. HCAL Muon chambers Tracker 4T solenoid ECAL Iron yoke Compact Muon Solenoid Total weight:12,500t Overall diameter:15m Overall length:21.6m Magnetic field:4T Elba May 2006 R M Brown - RAL 3

  4. Coloured histograms are separate contributing backgrounds for 1fb-1 ECAL design objectives High resolution electromagneticcalorimetry is central to the CMS design Benchmark process: H    m /m = 0.5[E1/E1  E2/E2   / tan(/2)] Where:E/E = a/E  b  c/E Aim (TDR): Barrel End cap Stochastic term: a= 2.7% 5.7% (p.e. stat, shower fluct, photo-detector, lateral leakage) Constant term: b= 0.55% 0.55% (non-uniformities, inter-calibration, longitudinal leakage) Noise: Low Lc= 155MeV 770MeV High L210MeV 915MeV (dq relies on interactionvertex measurement) (electronic, pile-up) Optimised analysis Elba May 2006 R M Brown - RAL 4

  5. Challenges & Choices Challenges: • Fast response (25ns between bunch crossings) • High radiation doses and neutron fluences (10 year doses: 1013 n/cm2, 1kGy at =0 2x1014 n/cm2, 50kGy at  =2.6) • Strong magnetic field (4 Tesla) • On-detector signal processing • 0/ discrimination • Long term reproducibility Choices: • Lead tungstate crystals • Avalanche photodiodes (Barrel), Vacuum phototriodes (Endcaps) • Electronics in 0.25 mm CMOS • Pb/Si Preshower detector in Endcap region • Laser light monitoring system Elba May 2006 R M Brown - RAL 5

  6. Fast light emission: ~80% in 25 ns Peak emission ~425nm (visible region) Short radiation length: X0 = 0.89cm Small Molière radius: RM = 2.10cm Radiation resistant to very high doses But: • Temperature dependence ~2.2%/OC • Stabilise to  0.1OC Formation and decay of colour centresin dynamic equilibrium under irradiation • Precise light monitoring system Low light yield (1.3% NaI) • Photodetectors with gain in mag field Leadtungstateproperties Elba May 2006 R M Brown - RAL 6

  7. Pb/Si Preshowers: 4 Dees (2/endcap) 4300 Si strips (~ 63x1.9 mm2) Tapered crystals Pointing ~ 3o from vertex Barrel: 36 Supermodules (18 perhalf-barrel) 61200 Crystals (34 types) – total mass 67.4t Dimensions: ~ 25x25x230 mm3 (25.8X0) DxD = 0.0175 x 0.0175 Endcaps: 4 Dees (2 per endcap) 14648 Crystals (1type) – total mass 22.9t Dimensions: ~ 30x30x220 mm3 (24.7X0) DxD = 0.0175 x 0.0175 ↔ 0.05 x 0.05 ECAL Layout Elba May 2006 R M Brown - RAL 7

  8. Crystal production • Crystal delivery determines ECAL Critical Path • Suppliers: • BTCP (Bogoroditsk, Russia) ~ 1100/month • SIC (Shanghai, China) ~ 130/month • ~ 80% of Barrel crystals already delivered (48950/61200) • Preseries of Endcap crystals: 100 BTCP, 300 SIC • Last Barrel crystal delivery Feb 2007 • Last Endcap crystal delivery Jan 2008 Elba May 2006 R M Brown - RAL 8

  9. SIC BTCP SIC BTCP Crystal Quality Assurance • Automatic control of: • Dimensions • Optical Transmission • Light yield • Longitudinal uniformity CERN INFN/ENEA Rome Transmission at 420 nm Light Yield Elba May 2006 R M Brown - RAL 9

  10. 8 0 7 0 6 0 T(%) 5 0 4 0 i n i t i a l 3 0 a f t e r i r r a d i a t i o n 2 0 1 0 0 3 0 0 3 5 0 4 0 0 4 5 0 5 0 0 5 5 0 6 0 0 6 5 0 7 0 0 w a v e l e n g t h ( n m ) 0 5 Light Yield Loss (%) Crystal Radiation Resistance Light loss is characterised by an ‘induced absorption’ Under irradiation at room temperature, a dynamic equilibriumforms between formation and annealing of colour centres.  Light loss saturates at a value that depends on dose-rate CMS specification requires: μ420 < 1.5 m-1(Under uniform (lateral) 60Co irradiation at >30 Gy/hr) Under LHC-like conditions for the Barrel (~0.15 Gy/hr) Light yield loss ≾ 6% Verification: BTCP: Use correlation between sharpness of absorption edge and radiation hardness (Check with sample irradiations) SIC: All crystals irradiated by producer Elba May 2006 R M Brown - RAL 10

  11. Endcaps: - Vacuum phototriodes (VPT) • More radiation resistant than Si diodes • (with UV glass window) • - Active area ~ 280 mm2/crystal • Gain 8 -10 (B=4T) Q.E.~20% at 420nm • Delivery ~80%  = 26.5 mm VPT Delivery & Test status MESH ANODE Photodetectors • Barrel - Avalanche photodiodes (APD) • Two 5x5 mm2 APDs/crystal • Gain: 50 QE: ~75% • Temperature dependence: -2.4%/OC • Delivery complete 40mm Elba May 2006 R M Brown - RAL 11

  12. VFE x 5 FE Front End card (FE) MB Trigger Sums LVR Data Trigger Tower (TT) Very Front End card (VFE) HV 2 x12 12 bits Logic 1 x6 12bitADC 2 bits 0 MGPA x1 APD/VPT VFE architecture for single channel On-detector electronics • Trigger primitives computed on the detector • Command&controlviatokenring • Modularity: Trigger Tower (25 channels in Barrel) • - 1 Low Voltage Regulation Board (LVR) • 5 VFE Boards (5 channels each) • 1 FE Board • 1 Fibre sending trig primitives (every bunch Xing) • 1 Fibre sending data (on Level1 accept) Elba May 2006 R M Brown - RAL 12

  13. ASICs in 0.25 mm IBM CMOS Technology • Very high yield (typically >85%) • ADC MGPA FENIX • Status: • All ASICS procured and tested • All systems for 30 SMs are tested & burned-in Full Barrel set available for most components • Endcap components following close behind 30 MeV 45 MeV Noise distribution for 1700 channels of SM13 View of a SuperModule (SM) showingon-detector electronics On-detector electronics: status Elba May 2006 R M Brown - RAL 13

  14. Clock & Control System (CCS) Trigger Concentrator Card (TCC) Data Concentrator Card (DCC) • Status: • CCS finished for whole ECAL • DCC in production for Barrel • TCC for Barrel: Production started • TCC For Endcaps: Schematic finishedFirst board by September LV Power supplies: ~60% of Barrel ordered (rest soon) Order for Endcaps in 2007 Off-Detector electronics Elba May 2006 R M Brown - RAL 14

  15. DT at APD when electronics is powered-up(Worst case: Bottom Supermodule) Cooling &Temperature Stability • Power dissipation of Barrel on-detector electronics ~160 kW • Combined temperature sensitivity of (crystal + APD):  Stabilise temperature to better than ± 0.05 OC • Chilled water at 50l/s Water manifold and pipes on SM Cooling bars in direct contact with electronic cards Elba May 2006 R M Brown - RAL 15

  16. The Problem: Colour centres form in PWO under irradn Transparency loss depends on dose rate Equilibrium is reached after a low dose Partial recovery occurs in a few hours Correlation between transmission losses for scintillation light and laser light 0.95 The Solution: Damage and recovery during LHC cycles tracked with a laser monitoring system 2 wavelengths are used: 440nm and 796nm Light is injected into each crystal Normalisation given by PN diodes (0.1%) Simulation of crystal transparency evolution at LHC (L =2x1033cm-2s-1)- based on test beam irradiation results Laser light monitoring (1) Elba May 2006 R M Brown - RAL 16

  17. An optical switch directs light to one half-supermodule orone quarter Dee at a time 440nm 796nm Light is injected through fibres into the front (Barrel) orrear (Endcap) of each crystal Resolution before irradn / after irradn and correction Laser light monitoring (2) APD Elba May 2006 R M Brown - RAL 17

  18. Sub-module: 10 crystals Module: 400/500 crystals Bare SM SM with cooling Super-module: 1700 crystals Assembly status: 26/36 bare SMs assembled 15/36 SMs completed Production rate 4/month Construction: Barrel 2 Regional Centres: CERN and Rome Elba May 2006 R M Brown - RAL 18

  19. Supercrystal: 25 crystals Dee (½ endcap): 3662 crystals Backplates successfully test mounted on HCAL Construction: Endcaps Production status All mechanical parts delivered Endcap crystal production starts in summer 2006 Elba May 2006 R M Brown - RAL 19

  20. Preshower detector • Rapidity coverage: 1.65< ||< 2.6 (End caps) • Motivation: Improved 0/ discrimination • 2 orthogonal planes of Si strip detectors behind • 2 X0 and 1 X0 Pb respectively • Strip pitch: 1.9mm (63mm long) • Area: 16.5m2 (4300 detectors,1.4x105channels) • High radiation levels - Dose after 10 yrs: • ~2x1014n/cm2 • ~60kGy •  Operate at -10oC Elba May 2006 R M Brown - RAL 20

  21. Status of Preshower Detector Micromodules System motherboards - production finished by end 2006 System Tests Ongoing - 8 ladders shown here Ladders Pre-series underwayProduction by mid 2007 Mechanics Preshower on schedule forinstallation at end of 2007 Off-Detector Readout Electronics First module alreadyprototyped – 12-channeloptical receiver (optoRx) Production completed ~September 07 All ES “complete disc” elements ready for installation at end 2006(before the beam pipe) D.Barney Elba May 2006 R M Brown - RAL 21

  22. Cosmic muons Event: 4161 Cry: 168 Cosmic Muon Test&Calibration • Each SM operated with cosmic rays for ~1 week  Intercalibration: 1-3% (stat) depending on η Mip deposits ~250MeV(increase APD gain from 50 to 200) Status: 10 SM Calibrated Muons through full crystal Elba May 2006 R M Brown - RAL 22

  23. Intercalibration from Laboratory Measurements During assembly, all detector components are characterised Thus the relative calibration ci of each channel may be estimated: Where: LY is crystal light yield, M and eQ are gain and quantum efficiency of the photo-detectorscele is the calibration of the electronics chain Ratio: Test beam/Lab Test beam vs Lab Intercalibration s = 4.2% Elba May 2006 R M Brown - RAL 23

  24. EB+ EB+ Surface Installation EB- Surface Installation (12/18) EB- U’ground Installation (6/18) EB- Reduced time 3→2months Barrel construction schedule Elba May 2006 R M Brown - RAL 24

  25. Insertion at point 5 ECAL Barrel installation Gap HB+/HB- ~ 1mm SM Rails on HB+ 2 SMs inserted 27 April for magnet test Supermodule Installation Elba May 2006 R M Brown - RAL 25

  26. ECAL Endcap installation Endcap Construction Schedule • Assembly plan assumes last EE crystal delivered end Jan 08. • Aim is to have Endcaps installed for 2008 Physics Run • All cables and services are already installed • Goal: D1 Sept07, D2 Nov07, D3 Jan08, D4 Apr08 Elba May 2006 R M Brown - RAL 26

  27. Summary • High resolution electromagnetic calorimetry is a central feature of CMS • The construction of the Barrel ECAL is in the final phase • All mechanical components are delivered for the Endcap ECAL • Crystal delivery sets the schedule for both Barrel and Endcap • The Pre-shower detector is on course for completion as planned • Supermodules are being commissioned and calibrated with cosmic rays • The CMS ECAL will meet its design goals – see next talk! Elba May 2006 R M Brown - RAL 27

  28. Spares Elba May 2006 R M Brown - RAL 28

  29. Pre-calibration In-situ calibration -symmetry w/jet trigger (ET > 120 GeV) Initial pre-calibration by ‘dead reckoning’ based on lab measurements (~4%) • Precision with 11M events • Limit on precision Inter-calibration precision % Lab LY Fast in-situ calibration based on principle that mean energy deposited by jet triggers is independent of  at fixed  (after correction for Tracker material)(~2-3% in few hours) 0 0.5 1.0  Test Beam LY  = 4.0% -ringinter-calibration andZe+e cross-calibration (~1% in 1 day) Z e + e Barrel Test Beam LY – Lab LY Calibration strategy Lab measurements Reference pre-calibration of few SM with 50/120GeV electrons in test beam (<2%) Finally: calibration to < 0.5% with W   + e in ~2 months 70 80 90 100 GeV Elba May 2006 R M Brown - RAL 29

More Related