1 / 34

CCNA 3/Module 1

CCNA 3/Module 1. Introduction to Classless Routing. Overview: Classful/Classless Routing. Classful routing - a network must use the same subnet mask for the entire network. Classless routing – using more than one subnet mask for a network address “subnetting a subnet”.

adanna
Download Presentation

CCNA 3/Module 1

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. CCNA 3/Module 1 Introduction to Classless Routing

  2. Overview: Classful/Classless Routing • Classful routing - a network must use the same subnet mask for the entire network • Classless routing – using more than one subnet mask for a network address • “subnetting a subnet”

  3. Overview: (Classful) IPv4 Addressing Limits • IPv4 – 20 years old • IPv4 – even with subnetting, couldn’t handle the global demand for Internet connectivity • Class B space was on the verge of depletion. • Rapid and substantial increase in the size of the Internet's routing tables. • As more Class C's came online, the flood of new network information threatened Internet routers' capability to cope.

  4. Overview: (Classful) IPv4 Addressing Limits • Provides IP scheme with limitations: • Class A – 126 networks: 16,777,214 hosts each • Class B – 65,000 networks: 65,534 hosts each • Class C – 2 million networks: 254 hosts each • While available addresses were running out, only 3% of assigned addresses were actually being used! • Subnet zero, broadcast addresses, pool of unused addresses at Class A and B sites, etc.

  5. Overview: Scalability & Routing Tables • Maximum theoretical routing table size is 60,000 entries. • Classful addressing would have hit this capacity by mid-1994. • Internet growth would have ended.

  6. 1.1.1 What is VLSM and why is it used? • The purpose of VLSM is to alleviate the shortage of IP addresses • VLSM allows: • More than one subnet mask within the same network • Or . . . Multiple SNMasks with ONE IP Address • Use of long mask on networks with few hosts • Use of short mask on networks with many hosts • In order to use VLSM, the routing protocol must support it. • Cisco routers with the following routing protocols support VLSM: • OSPF (Open Shortest Path First) • IS-IS (Integrated Intermediate System to Intermediate System) • EIGRP (Enhanced Interior Gateway Routing Protocol) • RIP v2 • Static Routing No RIP v1

  7. 1.1.1 What is VLSM and why is it used? Classfulrouting protocols use one subnet mask for a single network • Ex: 192.168.187.0, must use subnet mask 255.255.255.0 VLSMallows a single autonomous system to have networks withdifferent subnet masks, for example: • Use a 30-bit subnet mask on network connections • (255.255.255.252) • Use a 24-bit subnet mask for user networks up to 250 users • (255.255.255.0) • Use a 22-bit subnet mask for user networks up to 1000 users • (255.255.252.0)

  8. 1.1.2 A waste of space • In classless routing, it was recommended that firstand lastsubnet not be used • First (SN 0) had same address for the network and subnet • Last subnet (all-1’s) was the broadcast • Always could have been used, was not recommended practice • Address depletion has lead to use of these subnets • Now acceptable practice to use the first and last subnets in conjunction with VLSM

  9. 1.1.2 A waste of space

  10. 1.1.2 A waste of space If subnet zero is used, there are 8useable subnets • Each subnet can support 30 hosts • Cisco routers use subnet zero by default IOS v. 12.0+ If no ip subnet-zero command is used on the router, there are 7useable subnets with 30 hosts per subnet • If supporting 4 routers (1 subnet each) that need3WAN links to each other, all subnets are used • No room for growth • Waste of 28 host addresses for each WAN (point-to-point) links or 1/3 of potential address space

  11. 1.1.2 A waste of space FOSTER(config)#no ip subnet-zero • Disables the capability to use subnets that include the network address of the unsubnetted network

  12. 1.1.3 When to use VLSM Design addressing scheme that allows: • Growth • Doesn’t waste addresses on point-to-point links • VLSM addressing applied instead results in: • Variable sized subnets • Take 1 of the 3 subnets and subnet it again • Example 192.168.187.224(last subnet) • Apply a 30 bit mask (225.225.225.252) • Creates a possible8 rangesof addresses with30 bits • Best solution forpoint-to-point links – use 2 host addresses instead of 30

  13. 1.1.4 Calculating subnets with VLSM VLSM helps to manage IP addresses • VLSM can use one SNM for a point-to-point link and one SNM for a LAN 0

  14. 1.1.4 Calculating subnets with VLSM Foster’sFabulousFilms • 2 routers • 1 in Hollywood (100 hosts) • 1 in Ravenna (50 hosts) • 1 WAN link (2 needed) • IP/NW Address: 192.16.10.0 • Class C • Use the BIGGEST first: • 100 • 50 • 2

  15. 1.1.4 Calculating subnets with VLSM Foster’sFabulousFilms • 2 routers • 1 in Hollywood (100 hosts) • 1 in Ravenna (50 hosts) • 1 WAN link (2 needed) • IP/NW Address: 192.16.10.0 • Class C • Use the BIGGEST first: • 100 /25 • 50 /26 • 2 /30 126 usable hosts 62 usable hosts 2 usable hosts

  16. 1.1.4 Calculating subnets with VLSM If VLSM were used instead of classful routing: • A 24-bit mask could be used for LAN segments for 250 hosts • A 30-bit mask could be used for WAN segments for 2 hosts • 172.16.32.0/20 (would accommodate 4094 hosts) • Binary = 10101100.00010000.00100000.00000000 • SNM = 11111111.11111111.11110000.00000000 • VLSM address172.16.32.0/26 (needed for 62 hosts) • Binary = 10101100.00010000.00100000.00000000 • SNM = 11111111.11111111.11111111.11000000 • If 172.16.32.0/20 used, but only 10 hosts on segment, would provide 4094 hosts and waste 4084 addresses • By further subnetting /20 to /26, gain 64 subnets (26) each supporting 62 hosts

  17. 1.1.4 Calculating Subnets w/VLSM Procedure to subnet a subnet /20 to /26 using VLSM: 1. Write 172.16.32.0 in binary form • Binary = 10101100.00010000.00100000.00000000 • Draw a vertical line between the 20th and 21st bits (the original subnet boundary) 3. Draw a vertical line between the 26th and 27th bits extending the bits to segment/host needs 4. Calculate the number of subnet addresses between the two vertical lines (lowest to highest) in value

  18. 1.1.4 Calculating Subnets w/VLSM • Keep in mind that only unused subnets can be further subnetted • If any address for a subnet is used cannot be further subnetted

  19. 1.1.5 Route Aggregation w/VLSM • Every network needs a separate entry in routing table • Each subnet needs a separate entry • Aggregation will reduce routing table size • When using VLSM keep subnetwork numbers grouped together in the network to allow for aggregationby using Classless InterDomain Routing(CIDR) • 172.16.14.0 • 172.16.15.0 • Router needs to carry only one route 172.16.14.0/23 14 in Binary = 00001110 15 in Binary = 00001111

  20. 1.1.5 Route Aggregation w/VLSM • Using CIDR and VLSM prevents address waste and promotes route aggregation or summarization • Without summarization, Internet would collapse • Summarization reduces burden on upstream routers • This process of summarization continues until entire network is advertised as a single aggregate route • Summarization is also called supernetting • Possible if the routers of a network run a classless routing protocol such as OSPF or EIGRP • Consists of IP address and bit mask in routing updates • The summary route uses prefix common to all addresses of organization

  21. 1.1.5 Route Aggregation w/VLSM Carefully assign addresses in a hierarchical fashion to share same high-order bits for summarization • A router must know subnetsattached in detail • A router doesnot need to tellother routers about subnets • A router using aggregate routes has fewer entries in routing table • VLSM allows for summarization of routes • Works even if networks are not contiguous • VLSM increases flexibly by summarization on higher-order bits • Used to calculate the network number of the summary route • Uses only shared highest-order bits

  22. 1.1.6 Configuring VLSM • If VLSM is chosen, it must be configured correctly • Example: 192.168.10.0 (Class C) • One router has to support 60 hosts, needs 6 bits in host portion of address to provide 62 possible address • (26 = 64 – 2 = 62) 192.168.10.0/26(leaves 6 bits for hosts) • One router has to support 28 hosts, needs 5 bits in host portion of address to provide 30 possible hosts • (25 = 32 – 2 = 30) 192.168.10.64/27(leaves 5 bits for hosts) • Two routers have to support 12 hosts each, needs 4 bits in host portion of address to provide 14 possible hosts (24 = 16 – 2 = 14) 192.168.10.96/28(leaves 4 bits for hosts) 192.168.10.112/28 (leaves 4 bits for hosts)

  23. 1.1.6 Configuring VLSM • Point-to-point connections are: • 192.168.10.128/30 (2 address required, 2 bits = 2 host addresses) • 192.168.10.132/30 (2 address required, 2 bits = 2 host addresses) • 192.168.10.136/30 (2 address required, 2 bits = 2 host addresses) • Choices = .136 .137 .138 .139 • Configuration as follows for the 192.168.10.136/30 network (.136/30 - network address;.139/30 - broadcast address; .137/30 and 138/30 – host addresses: • (config)#interface serial 0 • (config-if)#ip address 192.168.10.137 255.255.255.252 • (config)#interface serial1 • (config-if)#ip address 192.168.10.138 255.255.255.252

  24. 1.2.1 RIP History Internet is a collection of autonomous systems (AS) • Each AS is administered by a single entity • Each AS has its own routing technology Routing protocol used within AS is InteriorGateway Protocol Routing protocol used betweenAutonomous Systems is an Exterior Gateway Protocol RIP v1: • is an IGP that is classful • was designed to work within moderate-sized AS • is a distance vector routing protocol • by default, broadcasts entire routing table every 30 seconds • uses hop count as metric (16 max) • is capable of load balancing 6 equal-cost paths (4 default) • Does not send subnet mask information in its updates • Is not able to support VLSM or CIDR

  25. 1.2.1 RIP History If the router receives information about a network, and the receiving interface belongs to same network but is on a different subnet, the router applies the one subnet mask configured on the receiving interface • Class A default classful mask is 255.0.0.0 • Class B default classful mask is 255.255.0.0 • Class C default classful mask is 255.255.255.0

  26. 1.2.2 RIP v2 Features RIP v2 is an Improved version of RIP v1 with following features: • Distance vector protocol • Uses hop count as metric • Uses hold-down timers (prevent routing loops), default 180 sec. • Uses split horizon to prevent routing loops • Uses 16 hops as infinite distance • Provides prefix routing (sends subnet mask with route update) • Supports use of classless routing (VLSM) • Multicasts updates using 224.0.0.9 address for better efficiency • Provides authentication in updates • Clear text - default • MD5 encryption – typically used to encrypt enable secret passwords (Message-Digest 5)

  27. 1.2.3 Comparing RIP v1 & v2

  28. 1.2.4 Configuring RIP v2 To enable a dynamic routing protocol: 1. Select routing protocol • FOSTER(config)#router rip • FOSTER(config-router)#version 2 • Configure routing protocol with the network IP address (identify physically connected network that will receive routing tables) • FOSTER(config-router)#network 10.0.0.0 • FOSTER(config-router)#network 172.16.0.0 3. Assign IP/SNM to interfaces

  29. 1.2.5 Verifying RIP v2

  30. 1.2.5 Verifying RIP v2 • RIP updates table every 30 seconds • If no update received in 180 seconds, route marked as down • If no update after 240 seconds, removes from routing table entry

  31. 1.2.6 Troubleshooting RIP v2

  32. 1.2.7 Default Routes Three ways a router learns about paths: 1. Static routes – manual configuration of routes (next hop) • Uses ip route command 2. Default routes – manually defined path to take when there is no known route to a destination 3. Dynamic routes – routers lean paths by receiving updates from other routers

  33. 1.2.7 Default Routes Static Route Command: FOSTER(config)# ip route 172.16.1.0255.255.255.0172.16.2.1 FOSTER(config)# ip route 172.16.1.0255.255.255.0172.16.2.1 Default NW Default NW Tells that 8 bits of subnetting in effect Tells that 8 bits of subnetting in effect Next hop router Next hop router

  34. 1.2.7 Default Routes DYNAMIC PROTOCOL Default Route Command Used to: 1. Give packets that are not ID’d in the routing table a place to go • Usually a router that connects to the Internet 2. Connect a router with a static default route FOSTER(config)# ip default-network 192.168.20.0 Default NW

More Related