1 / 13

Chapter 2

Chapter 2. Wide Area Network Technologies. What is a WAN ?. The set of connecting links between local area networks These links can be made using: Public switched telephone network-PSTN Leased telephone lines (T1-1.5 Mbps, T3-44.7 Mbps) Fiber-optic cable Satellite links Packet radio waves

alden-pennington
Download Presentation

Chapter 2

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Chapter 2 Wide Area Network Technologies

  2. What is a WAN ? • The set of connecting links between local area networks • These links can be made using: • Public switched telephone network-PSTN • Leased telephone lines (T1-1.5 Mbps, T3-44.7 Mbps) • Fiber-optic cable • Satellite links • Packet radio waves • Microwaves • Internet

  3. What is a WAN ? – Continued • Most WANS are private and owned by the company that uses them • Internet is the largest WAN in the world • Companies are forming private WANs through encrypted communications over the Internet • WANs suffer from extremely limited bandwidths – many times slower than LANs • WAN links are good for short messages

  4. Some PSTN Services and Transmission Rates • X.25 56Kpbs • T1 1.5Mbps • T3 44.7Mbps • ATM 44.7Mbps

  5. SLIP • Serial Line Internet Protocol • Common protocol used to transmit IP packets over serial lines and telephone connections • Designed to handle just TCP/IP traffic – not other protocols • Must know your IP address and the IP address of the remote computer • SLIP does not provide for data compression

  6. PPP • Point-to-Point Protocol • Common protocol used to transmit IP packets over serial lines and telephone connections • PPP can transmit TCP/IP traffic as well as IPX, AppleTalk, etc. simultaneously • Offers data compression • Offers enhanced security • PPP has slowly replaced SLIP

  7. How IP Datagrams are Encapsulated by a Windows 2000 that Uses WAN Technology • Encapsulation done at Data Link Layer prior to being sent onto the physical medium • Delimiters – distinguishes each frame at the Data Link Layer as well as frame’s payload from header and trailer

  8. How IP Datagrams are Encapsulated – Cont • Protocol Identification – Used to distinguish different protocols on the WAN link such as TCP/IP, IPX, or AppleTalk • Addressing – Destination must be identified if multiple destinations are supported • Bit-level integrity check – Checksum process used

  9. Categories of WAN Encapsulations for IP Datagrams • Point-to-point links • Maximum of two nodes • No Data Link Layer addressing needed • Examples include analog phone lines, ISDN lines, T-1, T-3 • Non-Broadcast Multiple Access (NBMA) • Segment has more than 2 nodes • No facility to broadcast a single IP datagram to multiple locations • X.25, ATM

  10. SLIP Encapsulation • Provides only frame delimitation services • Does not provide protocol identification or bit-level integrity verification • Uses a special character called the END character (0xC0) • END is placed at the beginning and the end of each IP datagram • Character stuffing technique used to prevent the occurrence of the END character within the IP datagram • See Figure 2-1 for SLIP encapsulation

  11. Character Stuffing • Any occurrence of the END character inside the datagram is replaced with a sequence beginning with another special character called ESC (0xDB) • END is replaced with 0xDB-DC • ESC in original datagram is replaced by 0xDB-DD • See Figure 2-2 for example

  12. PPP Encapsulation • Flag – Indicates start and end of a PPP frame (1 byte) • Address – Used as a destination address on a multi-point network. On point-to-point links, the destination is the other node. The value of 0xFF is used here – the broadcast network (1 byte) • Control – always set to the same value (0x03) to indicate an unnumbered frame (1 byte) • Protocol – Used to identify the upper layer protocol of the frame (2 bytes) • 0x00-21 indicates IP datagram • 0x00-2B indicates IPX datagram

  13. PPP Encapsulation – Cont. • IP datagram – data from Network Layer • Frame Check Sequence – 2 byte FCS used for error detection. PPP frame is silently discarded if the sent FCS does not equal calculated FCS

More Related