1 / 23

Petroleum Equipment Institute RP 200-13

Petroleum Equipment Institute RP 200-13 Recommended Practices for Installation of Aboveground Storage Systems for Motor Vehicle Fueling. RP 200-13 Introduction Scope

asa
Download Presentation

Petroleum Equipment Institute RP 200-13

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Petroleum Equipment Institute RP 200-13 Recommended Practices for Installation of Aboveground Storage Systems for Motor Vehicle Fueling

  2. RP 200-13 Introduction Scope Includes aboveground, stationary, shop-fabricated tanks. Does not include field-fabricated storage tanks or storage systems for liquefied petroleum gases, liquefied natural gases or compressed natural gases.

  3. RP 200-13 1. Introduction Emphasizes the Importance of Using Competent Installers

  4. RP 200-13 2. Site Planning Tank Location Tank Configurations Property Lines and Bldgs Tank Spacing Requirements Bases and Foundations Retail Service Stations Commercial Fleet Facilities Marinas (Change) Product Deliveries Traffic Flow SPCC Plan Electronic Equipment Physical Protection Fire Protection Utilities Emergency Planning Change: Added: See RP1000

  5. RP 200-13 3. Foundations, Support and Anchorage General Soil Analysis Foundation Design Excavation Base Course Vertical Tank Bases Horizontal Tank Saddles Reinforced Concrete Slabs Anchoring

  6. RP 200-13 4. Dikes Purpose Dike Capacity Dike Construction Impervious Barrier Dike Penetraions Access Drainage Control Oil/Water Separator

  7. RP 200-13 5. Vaults and Special Enclosures General Vault Design Vault Construction Venting Leak Detection Liquid Recovery Vault Ventilation Collision Protection Electrical Installation Special Enclosures

  8. RP 200-13 6. Tanks General Standards (Changes) Tank Openings Preinstallation Inspection Material Handling Air-and-Soap Test Changes: Deleted UL2244 (Tank System) Added STI F921 (Integral Secondary Containment) Added STI F941 (Fireguard)

  9. RP 200-13 7. Pumps and Valves Materials and Design Pumping Systems Fire/Emergency Valves Block Valves Anti-Siphon Valves Check Valves Pressure Relief Valves

  10. RP 200-13 8. Tank Filling, Gauging, Dispensing and Venting Materials and Design Tank Filling Dispensing Systems Gauging Systems Tank Venting

  11. RP 200-13 9. Aboveground Piping and Fittings General Requirements AST Piping Materials Piping Practices Piping Layout Fittings for AST Piping Testing AST Piping Piping Corrosion Protection

  12. RP 200-13 10. Underground Piping and Fittings General Requirements Piping Materials Piping Practices Layout and Trenches Backfill and Compaction Fittings Corrosion Protection Fiberglass Piping Flexible Piping Containment Sumps Testing Primary Piping Testing Secondary Piping

  13. RP 200-13 11. Corrosion Protection General Applicability Coatings Protection of Buried Components Galvanic CP Impressed-Current Sys Wiring and Electrical Inspection and Testing

  14. RP 200-13 12. Environmental Protection General Release Detection Vapor Recovery

  15. RP 200-13 13. Electrical Installation General Requirements Classifications Electrical Equipment Emergency Shutoff Wiring Intrinsically Safe Grounding and Bonding Ensuring Uninterrupted Power

  16. RP 200-13 14. Testing and Inspection General Test Results Other Testing

  17. RP 200-13 15. Documentation, Maintenance and Training As-Built Drawings Component Documentation Scheduled Maintenance Training

  18. RP 200-13 Appendix A Size Calculations for Dikes

  19. RP 200-13 Appendix B Venting

  20. RP 200-13 Appendix C Code Requirements for ASTs at Motor Vehicle Fuel Dispensing Facilities

  21. RP 200-13 Appendix C Code Requirements NFPA 30A 2012 (2008) IFC 2012 (2006)

  22. RP 200-13 Appendix D Publication Reference

More Related