1 / 43

Chapter 10

Chapter 10. Sinusoidally Driven Oscillations. Question of Chapter 10. How do the characteristic frequencies generated in one object (say a piano string) excite vibrations in another object (say a sounding board)?. A Simple Driving System. Natural Frequency ( w o ).

astin
Download Presentation

Chapter 10

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Chapter 10 Sinusoidally Driven Oscillations

  2. Question of Chapter 10 • How do the characteristic frequencies generated in one object (say a piano string) excite vibrations in another object (say a sounding board)?

  3. A Simple Driving System

  4. Natural Frequency (wo) • If the board is a door, then the natural frequency is around 0.4 Hz. • If the system is driven at 0.4 Hz, large amplitudes result. • Smaller amplitudes result for driver frequency different from 0.4 Hz.

  5. Actual motions • The door starts with complex motions (transient) that settle down to sinusoidal, no matter the motor rate. • The final frequency is always the driving frequency of the motor (w). • The amplitude of the oscillations depends on how far from the natural frequency the motor is.

  6. Driving at Various Rates

  7. Natural Frequency Amplitude vs. Frequency

  8. w << wo • Motor frequency is far below the natural frequency (w << wo) door moves almost in step with motor. • Door moves toward motor when bands are stretched most.

  9. w < wo • Door lags behind the motor.

  10. w = wo • Door lags by one quarter cycle.

  11. w >> wo • Door lags by one-half cycle.

  12. w/wo Door Lags << 1 0 < 1 Small = 1 ¼-cycle >> 1 ½-cycle Summarizing

  13. Computer Model Click on the link and experiment

  14. Nature of the Transient • Transients are reproducible • If crank starts in the same position, we get the same transient • Damped Harmonic Oscillations • Shown by changing the damping • Imagine the bottom of the door immersed in an oil bath • The amount of immersion gives the damping

  15. Small Damping

  16. Heavier Damping

  17. Two Part Motion • Damped harmonic oscillation (transient) is at the natural frequency • Driven (steady state) oscillation is at the driver frequency

  18. Driver Frequency = Natural Frequency

  19. Damping and the Steady State • As long as we are far from natural frequency, damping doesn’t affect the steady state. • Near the natural frequency, damping does have an effect.

  20. Small damping W½ Amplitude Large damping Frequency Damping and the Steady State As damping is increased the height of the peak decreases

  21. Trends with Damping • As damping increases we expect the halving time to decrease ( )Oscillations die out quicker for larger damping. • As damping increases the maximum amplitude decreases ( ) • Also notice W½ D.Larger damping means a broader curve.

  22. Percentage Bandwidth (PBW) • Range of frequencies for which the response is it least half the maximum amplitude. • Let N be the number of oscillations that the pendulum makes in T½. • Direct measurement yields PBW = 38.2/N measured in %

  23. Example of PBW • Imagine tuning an instrument by using a tuning fork (A 440) while playing A. • If you are not matching pitch, the tuning fork is not being driven at its natural frequency and the amplitude will be small. • Only at a frequency of 440 Hz will the amplitude of the tuning fork be large

  24. Example of PBW - continued • T½ = 5 sec (it takes about 5 seconds for the tuning fork to decay to half amplitude) • N = (440 Hz) (5 sec) = 2200 cycles • So when you get a good response from the tuning fork, you have found pitch to better than PBW = 38.2/2200 = 0.017% or 0.076 Hz!

  25. Caution! • You must play long, sustained tones • Short “toots” will stimulate the transient which recall is at the natural frequency of the tuning fork (440 Hz) • Without the sustained driving force of the instrument, we will never get to the steady state and the tuning fork will ring due to the transient. • You will think the instrument is in pitch when it is not.

  26. Systems with Two Natural Modes • Each mode has its own frequency, decay time, and shape. • The modes are always damped sinusoidal. • Superposition applies.

  27. Simple Two Mass Model

  28. Normal Modes of Two Mass Model (Chapter 6) Let Mode 1 have a natural frequency of 10 Hz and Mode 2 a natural frequency of 17.32 Hz.

  29. 17.32 Hz 10 Hz Amplitude Frequency Driving Point Response Function or Resonance Curve

  30. Frequencies Between Peaks • Mass one has a mode one component and should lag a half-cycle behind the driver(w > wo1) • Mass one also has a mode two component to its motion, and here the driving frequency is less than the natural frequency (w << wo2) • Mass one keeps in step with the driver • These conflicting tendencies account for the small amplitude here

  31. New Terms • Driving Point Response Curve – measure the response at the mass being driven • Transfer Point Response Curve – measure the response at another mass in the system (not a driven mass)

  32. Properties of a Sinusoidally Driven System • At startup there is a transient that is made up of the damped sinusoids of all of the natural frequencies. • Once the transient is gone the steady state is at the driving frequency. When the driving frequency is close to one of the natural frequencies, the amplitude is a maximum and resembles that natural mode.

  33. A Tin Tray The tray is clamped at three places. Sensors ( )and drivers ( )are used as pairs in the locations indicated.

  34. Response Curves

  35. General Principles • Sensor cannot pickup any mode whose nodal line runs through it. • Notice that Sensor 2 is on the centerline • It cannot pick up modes with nodal lines through the center, such as…

  36. Sensor 2 is blind to…

  37. Sensor 2 is very sensitive to…

  38. Drivers Ability to Excite Modes • If a driver falls on the nodal line of a mode, that mode will not be excited • If a driver falls between nodal lines of a mode, that mode will be excited

  39. Steady State Response • Superposition of all the modes excited and their amplitudes at the detector positions. • Some modes may reinforce or cancel other modes. • Example – consider the modes on the next screen • Colored sections are deflected up at this time and the uncolored sections are deflected down • The vertical lines show where in the pattern of each we are for a particular position on the plate

  40. Superposing Two Modes

  41. Summary • Altering the location of either the driver or the detector will greatly alter what the transfer response curve will be. • Altering the driver frequency will also change the response.

  42. Three Cases Presented • Deflections of the same sign (giving a larger deflection)Add • Deflections of opposite sign (canceling each other out)Subtract • Deflection of one mode lined up with the node of the other (deflection due to one mode only)Single

  43. The G4 Phantom at G3 196, 392, 588, 784, 980, 1176, … Depress G3 slowly Press & release G4 392, 784, 1176, 1568, 1960, 2352, …

More Related