1 / 22

4100 HP

4100 HP. Maintenance Kit. Enter. The Maintenance Kit Parts. The kit comes with: a fuser a transfer roller a pickup roller feed rollers a tool for removing the transfer roller HP also recommends the use of a flat blade screwdriver to remove the pickup roller. Exit.

baruch
Download Presentation

4100 HP

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. 4100 HP Maintenance Kit Enter

  2. The Maintenance Kit Parts • The kit comes with: • a fuser • a transfer roller • a pickup roller • feed rollers • a tool for removing the transfer roller • HP also recommends the use of a flat blade screwdriver to remove the pickup roller. Exit

  3. Steps to Replacing the Kits • 1 - Replacing the fuser • 2 - Replacing the transfer roller • 3 - Replacing tray 1 pickup roller • 4 - Replacing the feed rollers in tray 2 and 3 • 5 - Replacing the feed rollers inside printer. • 6 - Resetting the page count Exit

  4. Step 1: Replacing the Fuser • Remove the tray 2 dust cover or optional duplexer at the rear of the printer. • Unplug the power cord from the printer • Open the rear output bin and pull out the extension Exit

  5. Step 1: Replacing the Fuser • Remove the rear output bin and extension • Bend the middle down slightly • Release tab 1 • Then release tab 2 Exit

  6. Step 1: Replacing the Fuser • Release the fuser by turning the fuser levers so that they point up. • Pull the fuser out of the printer • Hold the back of the printer while pulling the fuser out. • Do not pull on the black plastic flapper. Exit

  7. Step 1: Install the New Fuser • Install the new fuser, left side first. Be sure to push it firmly into the printer. • Lock the fuser in place by rotating the levers to the horizontal position. The levers will lock only if the fuser is installed all the way. • Replace the rear output bin, left side first. • Plug the power cord into the printer • Replace the duplexer. Exit

  8. Step 2: Replacing the Transfer Roller • Open the top cover and remove the toner cartridge. The transfer roller in underneath the toner cartridge. Exit

  9. Step 2: Replacing the Transfer Roller • Using the plastic tools that had been provided in the kit, pry the left end of the metal shaft up. Then slide the transfer roller to the left to remove. Exit

  10. Step 2: Replacing the Transfer Roller • Install the new transfer roller by sliding the right side in place first. Then snap the left side (with the gear) into place. • NOTE: When installing the transfer roller, make sure the black collar on the left side is oriented properly, with the open end down. Exit

  11. Step 3: Replacing the Tray 1 Pickup Roller • Open tray 1 and locate the rubber pickup roller at the center of the tray. • Pull the envelope entrance cover straight out of the printer. • Using a flat blade screwdriver, pry open the blue latch on the pickup roller. Then lift out the pickup roller. Exit

  12. Step 3: Replacing the Tray 1 Pickup Roller • Install the new pickup roller and snap the blue latch back into place. • Note: make sure the pin in the pickup roller lines up with the hole in the shaft. • Reinstall the envelop entrance cover. Exit

  13. Step 4: Replacing the Feed Rollers Each paper tray has a roller located inside. Each feed roller is located inside the printer when the paper tray is removed. • Remove the paper tray from the printer. • Pinch the blue latch on the left side of the feed roller and slide the feed roller off the shaft. Exit

  14. Step 4: Replacing the Feed Rollers • Slide the new feed roller onto the shaft until it locks into place. • Note: it is very important that the feed roller locks into place. • Close the door until it locks in place • Note: the door must be fully closed to avoid damaging the printer. Exit

  15. Step 5: Replacing the Feed Rollers in the Printer • Remove the paper tray from the printer • Pinch the blue latch on the left side of the feed roller and slide it off the shaft. It might be necessary to rotate the feed roller in order to pinch the latch. Exit

  16. Step 5: Replacing the Feed Rollers in the Printer • Slide the new feed roller onto the shaft and rotate it until it locks into place • Note: It is very important that the feed roller locks into place • Replace the paper tray • Continue with step 6 to reset the page count. Exit

  17. Step 6: Resetting the Page Count • Now it is time to reset the page count and clear the error message. • To see how to do that visit the LM page. Exit

  18. The Fuser

  19. The Transfer Roller

  20. Pickup Roller

  21. Feed Rollers Feed Rollers Pickup Roller

  22. Tool for Removing the Transfer Roller

More Related