1 / 14

Ssd simulation status : preparation for embedding

Ssd simulation status : preparation for embedding. Jonathan Bouchet Svt Meeting : 09/19. Ssd simulation chain. SsdSimulationMaker SLS (slow simulator) Simulate charge over the strips SPA Signal+pedestal+noise Addition Pedestal supression Zero supression. SsdClusterMaker SCF

camden
Download Presentation

Ssd simulation status : preparation for embedding

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Ssd simulation status : preparation for embedding Jonathan Bouchet Svt Meeting : 09/19

  2. Ssd simulation chain SsdSimulationMaker SLS (slow simulator) Simulate charge over the strips SPA Signal+pedestal+noise Addition Pedestal supression Zero supression SsdClusterMaker SCF Scan the strips Form the clusters SCM Associate the clusters

  3. Ssd Reconstruction Chain SsdDaqmaker Scan the strips and store the pedestals, id and noise into assdStripCalib table SsdPointMaker Do the reconstruction of the clusters Match the clusters to form a hit

  4. To recall

  5. Ssd soft : real data vs simu • Many differences between the 2 codes • Real Data : • pick the ssdStripCalib (pedestal and noise) accorging to the time stamp • in /Calibration/ssd. • Reco : (s/n)>5 && noise > 0. • Geometry : ssdWafersPosition.C (the geometry with alignment corrections) • Simu : • The actual calibration : pedestal =100 ADC , noise = 3 ADC • in /starDb/svt/ssd/ • Reco : (s/n)> 5 only • Geometry : geom.C (old) • To have a consistent simu with respect to the data, we must have makers and parameters (noise, pedestal, geometry) equivalent

  6. New way for embedding StSsdDaqMaker DAQ File StSsdPointMaker Spa_strip StSsdSimulationMaker Fzd File St_scf_Maker St_scm_Maker • old chain : StSsdSimulationMaker + St_scf_Maker + St_scm_Maker • New chain : StSsdSimulationMaker + StSsdPointMaker

  7. Noise of the clusters P-side N-side Simulation Real data

  8. Noise : with the new calibration P-side N-side

  9. Charge of the clusters Pedestal = 100 ADC Noise = 3 ADC With real pedestal and noise values • Remove the large tail for the fake clusters (noise)

  10. Comparison between the 2 chains: signal to noise Old chain New chain

  11. Size of the clusters [strips] New chain Old chain • The 2 chains give the same results

  12. Comparison with the efficiencies • Within the bars errors, efficiencies look the same for the 2 chains Old chain New chain

  13. Efficiency • The efficiency looked better (agree with the real data) • But it was before a correction (use simu flag in StSsdDbMaker) • After this correction , efficiency get back to 70 % • Bands in residuals • The difference between efficiencies in simu vs real data still here until now

  14. Summary,outlook • Old Db vs ssdStripCalib • Effect on the clusters properties (noise,size) • Consistant with the real data • Old reco chain vs new reco chain • The 2 chains give similars results (number of ssdHit reco,efficiency) • Not entirely ready for embedding (see previous problem) • Check efficiency (if agree with real data) • Then eliminate old makers (status of StSsdEvalMaker)-->rename Ssd simu chain • Create StSsdMixer for embedding

More Related