1 / 1

Integrated Microfluidic Systems for Automatic Glucose Sensing and Insulin Injection

Integrated Microfluidic Systems for Automatic Glucose Sensing and Insulin Injection 1 Chao-June Huang , 2 Chih-Hao Wang, 3 Yi-Hsin Chen, 3 Tse-Chuan Chou and, 1,2 Gwo-Bin Lee, 4 Xi-Zhang Lin, and 4 Ming-Hua Chen

chogan
Download Presentation

Integrated Microfluidic Systems for Automatic Glucose Sensing and Insulin Injection

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Integrated Microfluidic Systems for Automatic Glucose Sensing and Insulin Injection 1Chao-June Huang, 2Chih-Hao Wang, 3Yi-Hsin Chen, 3Tse-Chuan Chou and, 1,2Gwo-Bin Lee, 4Xi-Zhang Lin, and 4Ming-Hua Chen 1Institute of Micro-Electro-Mechanical-System Engineering, 2Department of Engineering Science, 3Department of chemical engineering, 4Department of Internal Medicine1 National Cheng Kung University 30 psi 25 psi Lower substrate Upper substrate Polyprrole GOD 2 1 20 psi 1.SU-8 spin coating 1.PR patterning Pumping rate (μl/min) 2.Photolithography 2.Ag deposition 3.PDMS casting Working electrode :Pt 3.Lift off 3 4 H2O2 Glucose injection 4.02 Plasma treatmnet and bonding 4.Au/Pt deposition : Ag : Silicon Bonding : Pt : PDMS : Au : SU-8 : Glass Frequency (Hz) Abstract This study presents a new Microfluidic system capable of real-time glucose measurement and automatic insulin injection. The hand-held system used MEMS (Micro-Electro -Mechanical-Systems) techniques, which integrated micro-pumps, micro-valves, microchannels, needles and glucose sensing electrodes on a small chip. Glucose monitoring was performed in a process including blood sample collection, glucose concentration detection, and injection of insulin. Micro-pumps and micro valves were used to automate the whole process in this single chip. Preliminary data showed that the developed chip could successfully detect the glucose concentration and inject a specific amount of insulin through the needles. The developed system could be promising for on-line monitoring of human glucose concentration and precise injection of proper doses of insulin to maintain a stable blood glucose concentration. Results Design A series of photographs showing that insulin samples could be successfully injected using the developed micro-pumps through a stick needle. The relationship between pumping rate and driving frequency for different working pressures. Schematic representation of the Microfluidic GSII (Glucose sensing and insulin injection) biochip (top-view). Fabrication blood sugar concentration (mg/dL) time (min) Glucose response after injection of 0.3cc insulin in a mouse body Output current of the glucose sensor at various glucose concentrations. Conclusions • This study presented a MEMS-based Microfluidic system capable of performing the measurement of the glucose concentration and the insulin injection in an automatic and real-time fashion. • Experimental results showed the glucose concentrations ranging from 1.61 to 30 mM can be detected. The sensitivity of the glucose sensor is measured to be 0.99 nA/mM • The sensitivity is comparable to large-scale traditional detection system. • The sample consumptions of the proposed chip device is less than 30μL A simplified fabrication process for the Microfluidic chip. • Pyrrole 0.05M & GOD 0.5mg/ml with 0.1M KCl. • Applied current 4.584uA for 130s on Pt. • Sink in P.B.S as blank phase. When electrode stable inject glucose. • GOD oxide glucose • Produce H2O2 • Sensing at 700mV vs. Ag/AgCl 2006 MML MEMS design and Micro-fabrication Lab A simplified fabrication process for the working electrode.

More Related