1 / 26

CNT Based Solar Cells MAE C187L

CNT Based Solar Cells MAE C187L. Joyce Chen Kari Harrison Kyle Martinez. Our Approach. An array of micro-sized “blocks” composed of single walled carbon nanotubes coated with photovoltaic materials and anti-reflective coating on a silicon wafer

chul
Download Presentation

CNT Based Solar Cells MAE C187L

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. CNT Based Solar CellsMAE C187L Joyce Chen Kari Harrison Kyle Martinez

  2. Our Approach • An array of micro-sized “blocks” composed of single walled carbon nanotubes coated with photovoltaic materials and anti-reflective coating on a silicon wafer • The 3 dimensional surface causes light rays to be trapped inside the cell • This, combined with the anti-reflective surface reduces the percentage of reflected rays

  3. Our Approach

  4. Methodology • The single walled nanotubes are cheaper, easier to fabricate and have better electrical properties than multi walled nanotubes • Silicon based photovoltaic materials are cheaper than many alternatives, and proven to be successful and reliable • E-beam lithography and chemical vapor deposition were used where applicable because we are familiar with these processes

  5. Step 1: Silicon wafer

  6. Step 1: Silicon wafer • Clean a 2 inch silicon wafer with Acetone, Methanol and IPA • De-ionized water rinse • N2 blow dry

  7. Step 2a: E-beam Lithography:Spin Coating Photoresist

  8. Step 2a: E-beam Lithography:Spin Coating Photoresist • PMMA 495C2: 500 RPM for 5 seconds and 4000 RPM for 45 seconds • Soft bake Sample at 180C for 90 seconds

  9. Step 2b: E-beam Lithography:E-beam Patterning

  10. Step 2b: E-beam Lithography:E-beam Patterning • Make a pattern of 700 blocks x 700 blocks of 40um x 40um squares with 10 um gaps • Based on our limited knowledge, we would use the same parameters procedure as in Lab 1

  11. Step 2c: E-beam Lithography:Metal Deposition

  12. Step 2c: E-beam Lithography:Metal Deposition • Using chemical vapor deposition we would deposit a thin layer of iron oxide on top of the patterned resist and wafer

  13. Step 2d: E-beam Lithography:Photoresist Development and Metal Lift-Off

  14. Step 2d: E-beam Lithography:Photoresist Development and Metal Lift-Off • Soak PMMA developer for 30-40 sec • Isopropanol + MIBK at 3 to 1 volume ratio • Rinse in Isopropanol • Blow dry with N2

  15. Step 3: SWCNT Growth

  16. Step 3: SWCNT Growth • Place the wafer in a furnace heated to 1000C and pass an argon flow through the furnace • Replace the argon flow with a methane flow of 99% purity at a flow rate of 6150cm3/min under 1.25 atm for 10 minutes • Replace the methane flow with an argon flow and cool to room temperature

  17. Step 4: Photovoltaic Deposition

  18. Step 4: Photovoltaic Deposition • Using molecular beam epitaxy, deposit silicon phosphorus (n-type layer) and silicon boron (p-type layer) • Molecular beam epitaxy is a slow deposition of films taking place in a high vacuum

  19. Step 5: Anti-Reflective Coating Deposition

  20. Step 5: Anti-Reflective Coating Deposition • Use a Cooke Thermal Evaporator to deposit a layer of silicon monoxide on the solar cell • Program the Sigma Film Thickness mOnitor with these parameters • Density = 2.13 g/cm3 • Tooling = 126% • Z-ratio = 0.87

  21. Step 5: Anti-Reflective Coating Deposition • Fill a long tungsten boat with SiO fragments • Turn power up to 15% until boat beings to glow and stay there for 2 minutes • Switch on heating until and increase dial to 30% for 30 seconds, until deposition rate is between 0.3-0.5 angstroms/s • Slowly increase to 35%-40% • Once desirable thickness is obtained, close shutter and record thickness after 1 minute • Slowly reduce boat current to zero and switch of heating unit

  22. Cost Analysis • Iron Oxide $1.00/ounce • Silicon ~ $2.00/lb • Silicon monoxide ~ $1.45/g • Methane < $0.10/L • A typical solar cell costs ~$0.05/kwh • This cell uses less silicon, an expensive commodity, and should produce more energy per square meter – therefore we would expect it to cost at least the same, if not less per kwh

  23. Estimated Efficiency • A similar experiment obtained a 7% efficiency, while it is expected that  a 40% efficiency is possible • The addition of an anti-reflective coating can reduce the reflected light from 30% to 10%, which adds ~ 1% efficiency

  24. Lifespan • Current solar panels are rated ~ 30 years • It is still unknown how long carbon nanotubes will last, but we assume their lifespan is the same as the copper wires they are replacing, if not longer • This would make our solar cell life span also ~30 years

  25. Testing • Test in lab with UV light to determine kw per square meter • Test at different angles to the sun to determine the correct incident angle for maximum efficiency • Test in extreme temperatures, as well as in wind tunnels to determine structural stability

  26. References http://www.gtri.gatech.edu/casestudy/3d-solar-cells-boost-efficiency http://www.nanowerk.com/news/newsid=1763.php http://www.alfa.com/en/ge100w.pgm http://ostc.physics.uiowa.edu/~microfab/manuals/pdf/deposition-SiO.pdf http://blog.sciencenet.cn/upload/blog/file/2010/2/20102193247668823.pdf http://en.wikipedia.org/wiki/Photovoltaic_array http://en.wikipedia.org/wiki/Carbon_nanotubes_in_photovoltaics http://www.metalprices.com/FreeSite/metals/nickelalloy/nickelalloy.asp Lecture Slides and Lab Handouts

More Related