1 / 12

EACO News Magazine 2010 September

EACO News Magazine 2010 September. 2010-09: Topics. DVM Plus III up compatibility New control devices MIM-B16 MIM-B17 MIM-B18 How to change option code with MR-CH01. The next EACO News Magazine will be released 01 October ‘10.

cleo
Download Presentation

EACO News Magazine 2010 September

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. EACO News Magazine2010 September

  2. 2010-09: Topics • DVM Plus IIIup compatibility • New control devices • MIM-B16 • MIM-B17 • MIM-B18 • How to change option code with MR-CH01 The next EACO News Magazine will be released 01 October ‘10

  3. Compatibility table: DVM Plus III vs DVM Plus IIIup (1) Compatible Not compatible

  4. Compatibility table: DVM Plus III vs DVM Plus IIIup (2) • So it’s not allowed to make a module system with a mix of DVM Plus III and DVM Plus IIIup outdoor units • For our Digital Solution Devices there is a free compatibility between old and new outdoor units NO!

  5. MIM-B16: WHM interface module (1) • Opto-isolated Interface with pulse-type watt hour meters for electricity billing system • Max. 8 watt hour meters per interface module • Total 8 WHM interface module per DMS1/DMS2 • Pulse coefficient setting: 1Wh/pulse ~ 1000Wh/pulse • Pulse width setting: 20ms~400ms in 1ms intervals • Interval between pulses: minimum 3ms • No support of pulse coefficient with decimal points • Power data storage in non-volatile memory ( 8 channels) • Data recovery from power failure • Current time setting and display • Configuration information display on LCD • Error display (communication, out-of-range pulse width..) Pulse signal Max. 8 watt hour meters

  6. MIM-B16: WHM interface module(2) DMS2 MIM-B16 Power box Max. 8 MIM-B16’s RS485 Comm. Pulse signal Power supply Power supply Power Supply

  7. MIM-B17: BACnet Gateway (1) • Interface for BACnet management system • Max. 256 indoor units/ERVs support with max. 16 interface modules • Lower physical layer : RS485 • Upper physical layer : BACnet/IP

  8. MIM-B17: BACnet Gateway (2) RS485 Ethernet Max. 16 BACnet BMS Interface module

  9. MIM-B18: LonWorks Gateway (1) • Interface for Lon-Connection to LonWorks management system • Max. 128 indoor units/ERVs support • Communication : RS485 to LonWorks • Upper physical layer : FTT-10A • Combinational use of LonWorks and S-NET3/S-NET mini

  10. MIM-B18: LonWorks Gateway (2) RS485 FTT-10A Max. 16 Ethernet LonWorks BMS S-NET3 S-NET mini Interface module

  11. How to change option code with MR-CH01 (1) 24-bit option code setting • Remove one battery from the wireless remote controller. • Press the Temp ▲▼ buttons together and put the battery back to enter the option code setting mode. • Set two digits of the option code respectively. And press “Mode” to change to the next two digits. • Press the On/Off power button to change the option code. Initial display

  12. How to change option code with MR-CH01 (2) 24-bit option code setting Example : 027402 – 14221A – 200001 - 300000 ※ 20 digits (blue) except the page digitsmust be set Set the two digits using the Temp ▲▼ buttons Press “Mode” to move to the next two digits. Indicator◀ moves to the next operation mode icon Press “Mode” to move to the third option code page Then “OFF timer” is displayed Set the next 10 digits Press “On/Off” to set the new option code

More Related