1 / 71

Principles of Electronic Communication Systems

Principles of Electronic Communication Systems. Third Edition Louis E. Frenzel, Jr. Chapter 8. Radio Transmitters. Topics Covered in Chapter 8. 8-1: Transmitter Fundamentals 8-2: Carrier Generators 8-3: Power Amplifiers 8-4: Impedance-Matching Networks 8-5: Typical Transmitter Circuits.

corbett-richter
Download Presentation

Principles of Electronic Communication Systems

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Principles of ElectronicCommunication Systems Third Edition Louis E. Frenzel, Jr.

  2. Chapter 8 Radio Transmitters

  3. Topics Covered in Chapter 8 • 8-1: Transmitter Fundamentals • 8-2: Carrier Generators • 8-3: Power Amplifiers • 8-4: Impedance-Matching Networks • 8-5: Typical Transmitter Circuits

  4. 8-1: Transmitter Fundamentals • A radio transmitter takes the information to be communicated and converts it into an electronic signal compatible with the communication medium. • This process involves carrier generation, modulation, and power amplification. • The signal is fed by wire, coaxial cable, or waveguide to an antenna that launches it into free space. • Typical transmitter circuits include oscillators, amplifiers, frequency multipliers, and impedance matching networks.

  5. 8-1: Transmitter Fundamentals • The transmitter is the electronic unit that accepts the information signal to be transmitted and converts it into an RF signal capable of being transmitted over long distances.

  6. 8-1: Transmitter Fundamentals Every transmitter has four basic requirements: • It must generate a carrier signal of the correct frequency at a desired point in the spectrum. • It must provide some form of modulation that causes the information signal to modify the carrier signal. • It must provide sufficient power amplification to ensure that the signal level is high enough to carry over the desired distance. • It must provide circuits that match the impedance of the power amplifier to that of the antenna for maximum transfer of power.

  7. 8-1: Transmitter Fundamentals Transmitter Configurations • The simplest transmitter is a single-transistor oscillator connected to an antenna. • This form of transmitter can generate continuous wave (CW) transmissions. • The oscillator generates a carrier and can be switched off and on by a telegraph key to produce the dots and dashes of the International Morse code. • CW is rarely used today as the oscillator power is too low and the Morse code is nearly extinct.

  8. 8-1: Transmitter Fundamentals Figure 8-1: A more powerful CW transmitter.

  9. 8-1: Transmitter Fundamentals Transmitter Types • High-Level Amplitude Modulated (AM) Transmitter • Oscillator generates the carrier frequency. • Carrier signal fed to buffer amplifier. • Signal then fed to driver amplifier. • Signal then fed to final amplifier.

  10. 8-1: Transmitter Fundamentals • Low-Level Frequency Modulated (FM) Transmitter • Crystal oscillator generates the carrier signal. • Signal fed to buffer amplifier. • Applied to phase modulator. • Signal fed to frequency multiplier(s). • Signal fed to driver amplifier. • Signal fed to final amplifier.

  11. 8-1: Transmitter Fundamentals • Single-Sideband (SSB) Transmitter • Oscillator generates the carrier. • Carrier is fed to buffer amplifier. • Signal is applied to balanced modulator. • DSB signal fed to sideband filter to select upper or lower sideband. • SSB signal sent to mixer circuit. • Final carrier frequency fed to linear driver and power amplifiers.

  12. 8-2: Carrier Generators • The starting point for all transmitters is carrier generation. • Once generated, the carrier can be modulated, processed in various ways, amplified, and transmitted. • The source of most carriers is a crystal oscillator. • PLL frequency synthesizers are used in applications requiring multiple channels of operation.

  13. 8-2: Carrier Generators Crystal Oscillators • The only oscillator capable of maintaining the frequency precision and stability demanded by the FCC is a crystal oscillator. • A crystal is a piece of quartz that can be made to vibrate and act like an LC tuned circuit. • Overtone crystals and frequency multipliers are two devices that can be used to achieve crystal precision and stability at frequencies greater than 30 MHz.

  14. 8-2: Carrier Generators Crystal Oscillators • The Colpitts-type crystal oscillator is the most commonly used crystal oscillator. • Feedback is derived from a capacitive voltage divider. • Transistor configuration is typically an emitter-follower. • The output is taken from the emitter.

  15. 8-2: Carrier Generators Figure 8-6: An emitter-follower crystal oscillator

  16. 8-2: Carrier Generators Crystal Oscillators • Pulling, or rubbering capacitors are used to make fine adjustments to the crystal oscillator frequency. • Field-effect transistors (FETs) make good crystal oscillators. The Pierce oscillator is a common configuration that uses a FET. • An overtone crystal is cut so that it optimizes its oscillation at an overtone of the basic crystal frequency. • The term harmonic is often used as a synonym for overtone.

  17. 8-2: Carrier Generators Crystal Switching • If a transmitter must operate on more than one frequency, but crystal precision and stability are required, multiple crystals can be used and the desired one switched on. • Mechanical rotary switches and diode switches are often used in this kind of application. • Diode switching is fast and reliable.

  18. 8-2: Carrier Generators Figure 8-9: Using diodes to switch crystals.

  19. 8-2: Carrier Generators Frequency Synthesizers • Frequency synthesizers are variable-frequency generators that provide the frequency stability of crystal oscillators but the convenience of incremental tuning over a broad frequency range. • Frequency synthesizers provide an output that varies in fixed frequency increments over a wide range. • In a transmitter, a frequency synthesizer provides basic carrier generation. • Frequency synthesizers are used in receivers as local oscillators and perform the receiver tuning function.

  20. 8-2: Carrier Generators Phase-Locked Loop Synthesizer • The phase-locked loop (PLL) consists of a phase detector, a low-pass filter, and a VCO. • The input to the phase detector is a reference oscillator. • The reference oscillator is normally crystal-controlled to provide high-frequency stability. • The frequency of the reference oscillator sets the increments in which the frequency may be changed.

  21. 8-2: Carrier Generators Figure 8-10: Basic PLL frequency synthesizer.

  22. 8-2: Carrier Generators Direct Digital Synthesis • A direct digital synthesis (DDS) synthesizer generates a sine-wave output digitally. • The output frequency can be varied in increments depending upon a binary value supplied to the unit by a counter, a register, or an embedded microcontroller.

  23. 8-2: Carrier Generators Direct Digital Synthesis • A read-only memory (ROM) is programmed with the binary representation of a sine wave. • These are the values that would be generated by an analog-to-digital (A/D) converter if an analog sine wave were digitized and stored in the memory. • If these binary values are fed to a digital-to-analog (D/A) converter, the output of the D/A converter will be a stepped approximation of the sine wave. • A low-pass filter (LPF) is used to remove the high-frequency content smoothing the sine wave output.

  24. 8-2: Carrier Generators Figure 8-15: Basic concept of a DDS frequency source

  25. 8-2: Carrier Generators Direct Digital Synthesis • DDS synthesizers offer some advantages over PLL synthesizers: • The frequency can be controlled in very fine increments. • The frequency of a DDS synthesizer can be changed much faster than that of the PLL. • However, a DDS synthesizer is limited in its output frequencies.

  26. 8-3: Power Amplifiers • The three basic types of power amplifiers used in transmitters are: • Linear • Class C • Switching

  27. 8-3: Power Amplifiers Linear Amplifiers • Linear amplifiers provide an output signal that is an identical, enlarged replica of the input. • Their output is directly proportional to their input and they faithfully reproduce an input, but at a higher level. • Most audio amplifiers are linear. • Linear RF amplifiers are used to increase the power level of variable-amplitude RF signals such as low-level AM or SSB signals.

  28. 8-3: Power Amplifiers • Linear amplifiers are class A, AB or B. • The class of an amplifier indicates how it is biased. • Class A amplifiers are biased so that they conduct continuously. The output is an amplified linear reproduction of the input. • Class B amplifiers are biased at cutoff so that no collector current flows with zero input. Only one-half of the sine wave is amplified. • Class AB linear amplifiers are biased near cutoff with some continuous current flow. They are used primarily in push-pull amplifiers and provide better linearity than Class B amplifiers, but with less efficiency.

  29. 8-3: Power Amplifiers • Class C amplifiers conduct for less than one-half of the sine wave input cycle, making them very efficient. • The resulting highly distorted current pulse is used to ring a tuned circuit to create a continuous sine-wave output. • Class C amplifiers cannot be used to amplify varying-amplitude signals. • This type amplifier makes a good frequency multiplier as harmonics are generated in the process.

  30. 8-3: Power Amplifiers • Switching amplifiers act like on/off or digital switches. • They effectively generate a square-wave output. • Harmonics generated are filtered out by using high-Q tuned circuits. • The on/off switching action is highly efficient. • Switching amplifiers are designated class D, E, F, and S.

  31. 8-3: Power Amplifiers Linear Amplifiers • Class A Buffers • A class A buffer amplifier is used between the carrier oscillator and the final power amplifier to isolate the oscillator from the power amplifier load, which can change the oscillator frequency.

  32. 8-3: Power Amplifiers Figure 8-21: A linear (class A) RF buffer amplifier

  33. 8-3: Power Amplifiers Linear Amplifiers • Class B Push-Pull Amplifier • In a class B push-pull amplifier, the RF driving signal is applied to two transistors through an input transformer. • The transformer provides impedance-matching and base drive signals to the two transistors that are 180° out of phase. • An output transformer couples the power to the antenna or load.

  34. 8-3: Power Amplifiers Figure 8-23: A push-pull class B power amplifier

  35. 8-3: Power Amplifiers Class C Amplifiers • The key circuit in most AM and FM transmitters is the class C amplifier. • These amplifiers are used for power amplification in the form of drivers, frequency multipliers, and final amplifiers. • Class C amplifiers are biased so they conduct for less than 180° of the input. • Current flows through a class C amplifier in short pulses, and a resonant tuned circuit is used for complete signal amplification.

  36. 8-3: Power Amplifiers Tuned Output Circuits • All class C amplifiers have some form of tuned circuit connected in the collector. • The primary purpose of a tuned circuit is to form the complete AC sine-wave output. • A parallel tuned circuit rings, or oscillates, at its resonant frequency whenever it receives a DC pulse.

  37. 8-3: Power Amplifiers Tuned Output Circuits • The pulse charges a capacitor, which then discharges into an inductor. • The exchange of energy between the inductor and the capacitor is called the flywheel effect and produces a damped sine wave at the resonant frequency.

  38. 8-3: Power Amplifiers Figure 8-27: Class C amplifier operation

  39. 8-3: Power Amplifiers • Any class C amplifier is capable of performing frequency multiplication if the tuned circuit in the collector resonates at some integer multiple of the input frequency.

  40. 8-3: Power Amplifiers Neutralization • Self-oscillation exists when some of the output voltage finds its way back to the input of the amplifier with the correct amplitude and phase, and the amplifier oscillates. • When an amplifier circuit oscillates at a higher frequency unrelated to the tuned frequency, the oscillation is referred to as parasitic oscillation.

  41. 8-3: Power Amplifiers Neutralization • Neutralization is a process in which a signal equal in amplitude and 180° out of phase with the signal, is fed back. • The result is that the two signals cancel each other out.

  42. 8-3: Power Amplifiers Switching Power Amplifiers • A switching amplifier is a transistor that is used as a switch and is either conducting or nonconducting. • A class D amplifier uses a pair of transistors to produce a square-wave current in a tuned circuit. • In a class E amplifier, only a single transistor is used. This amplifier uses a low-pass filter and tuned impedance-matching circuit to achieve a high level of efficiency.

  43. 8-3: Power Amplifiers Switching Power Amplifiers • A class F amplifier is a variation of the E amplifier. • It contains an additional resonant network which results in a steeper square waveform. • This waveform produces faster transistor switching and better efficiency. • Class S amplifiers are found primarily in audio applications but have also been used in low- and medium-frequency RF amplifiers.

  44. 8-3: Power Amplifiers Linear Broadband Power Amplifiers • Newer wireless systems require broader bandwidth than the previously mentioned amplifiers can accommodate. • Two common methods of broad-bandwidth amplification are: • Feedforward amplification • Adaptive predistortion amplification

  45. 8-3: Power Amplifiers Linear Broadband Power Amplifiers • Feedforward Amplification • With this technique, the distortion produced by the power amplifier is isolated and subtracted from the amplified signal, producing a nearly distortion-free output signal. • The system is inefficient because two power amplifiers are required. • The tradeoff is wide bandwidth and very low distortion.

  46. 8-3: Power Amplifiers Figure 8-34: Feedforward linear power amplifier.

  47. 8-3: Power Amplifiers Linear Broadband Power Amplifiers • Adaptive Predistortion Amplification • This method uses digital signal processing (DSP) to predistort the signal in a way that when amplified, the amplifier distortion will offset the predistortion characteristics. • The result is a a distortion-free output signal. • The method is complex, but is more efficient than the feedforward method because only one power amplifier is needed.

  48. 8-3: Power Amplifiers Figure 8-35: Concept of adaptive predistortion amplification.

  49. 8-4: Impedance-Matching Networks • Matching networks that connect one stage to another are very important parts of any transmitter. • The circuits used to connect one stage to another are known as impedance-matching networks. • Typical networks are LC circuits, transformers, or some combination.

  50. 8-4: Impedance-Matching Networks • The main function of a matching network is to provide for an optimum transfer of power through impedance matching techniques. • Matching networks also provide filtering and selectivity.

More Related