1 / 15

Using Belt Air to Ventilate Active Working Areas

Using Belt Air to Ventilate Active Working Areas. Federal Coal Mine Health and Safety Act of 1969. Belt air could not be used to ventilate active works except for mines opened prior to the Act (Pre-Act Mines). Pre-Act mines could utilize belt air if needed with approval.

dane-chandler
Download Presentation

Using Belt Air to Ventilate Active Working Areas

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Using Belt Air to Ventilate Active Working Areas

  2. Federal Coal Mine Health and Safety Act of 1969 Belt air could not be used to ventilate active works except for mines opened prior to the Act (Pre-Act Mines) Pre-Act mines could utilize belt air if needed with approval

  3. Petitions for Modification First Petition Granted 1975 30 CFR § 75.326 § 75.326 became § 75.350 in subsequent ventilation rulemaking Approximately 90 Petitions granted from 1975 to 2003

  4. Prior to Final Rule : Two ways to use belt air Petition for Modification Pre-Act Mines still can use belt air with MSHA District Manager Approval

  5. Final Belt Air Rule April 2, 2004 All granted petitions are superseded Any Pre-Act mines must also comply with final rule

  6. Ventilation of Belt Conveyor Entries DW Mitchell and CW Parisi, 1988

  7. Federal Coal Mine Health and Safety Act of 1969 Act was based on information and technology available at the time Four research documents considered by Congress

  8. Mine Fires and Their Control Westfield (1966) summarized knowledge and experience from 572 fires 1952 to 1965 Three Discussion Points : • Electrical short-circuit protection required • Abandoning trolley haulage • Limiting air current in belt entry Only third was considered practical and implementable by Congress in 1969

  9. Float Dust Deposits in Return Airways in American Coal Mines USBM IC 8150 (1963) 50 mine study Study showed float coal dust levels deposited in belt entries was seven times that of returns

  10. Float Coal Hazard in Mines : A Progress Report USBM RI 6581(1965) 50 mine study • Higher velocities in return airways lowered concentration of float coal deposits • Float coal not raised into suspension by air velocities from 50 to 550 fpm

  11. Fire Hazard of Conveyor Belts USBM RI 7053(1967) • Rubber-based belting burned 10 to 30 times faster than other formulations (propagation) • Flame spread was higher with air movement in belt entry than zero-flow • Small fires were extinguished by automatic sprinklers

  12. Air Velocity Act limited air velocity and quantity to levels required to control methane gas and supply oxygen to men Intent in Act was to mitigate against fanning and propagating fire, contaminating mine entries prior to escape, and float coal dust

  13. Fire Detection Technology Heat activated point-type sensors (PTHS) were state of the art in 1969 PTHS still accepted in 30 CFR for non-belt air mines Belt Air Rule requires use of Atmospheric Monitoring (CO) System or Equivalent AMS provides increased detection ability and earlier warning to miners

  14. CONCLUSIONS BY MITCHELL Provisions providing a greater level of protection to miners include: • Allowing belt entries to be used to supplement ventilation at working faces • Isolating belt entry from primary escapeway • Permitting air velocities consistent with safe mining practices

  15. CONCLUSIONS BY MITCHELL Proposed warning and alarm levels of 10 and 15 ppm CO above ambient should be reconsidered Concentration of CO is based on size of fire and airflow in the entry Belt Air rule reduced levels to 5 and 10 ppm CO, and allow for further reductions based of USBM RI 9380

More Related