1 / 22

Bridge Seismic Isolation Study on a Full Scale Bridge Test

Bridge Seismic Isolation Study on a Full Scale Bridge Test. Myrto Anagnostopoulou SEESL Structural and Test Engineer Ricardo Ecker Lay Ph.D. Candidate Andre Filiatrault Professor, MCEER Director Dep. Of Civil, Structural and Environmental Engineering

domani
Download Presentation

Bridge Seismic Isolation Study on a Full Scale Bridge Test

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. Bridge Seismic Isolation Study on a Full Scale Bridge Test MyrtoAnagnostopoulou SEESL Structural and Test Engineer Ricardo Ecker Lay Ph.D. Candidate Andre Filiatrault Professor, MCEER Director Dep. Of Civil, Structural and Environmental Engineering University at Buffalo – State University of New York

  2. Design of seismically isolated structures is based on the mechanical properties of newly-fabricated seismic isolation hardware • Environmental effects, history of loading, aging result in change in: properties of isolation hardware behavior of isolated structure • Collect field data on the aging characteristics and long-term service life of seismic isolation bearings

  3. Full-Scale Isolated Bridge • Calspan’s Ashford facility, Western NY – 50 miles from UB • Two 72-foot long adjacent single lane concrete girder bridges at a distance of 6 feet • 8 low-damping elastomeric bearings of two different elastomeric compounds • Free vibration testing will be repeated weekly for a period of 5 years starting end-October 2010 • Remotely controlled testing from SEESL/UB facilities

  4. Superstructure Geometry • 10 girder beams: AASHTO Box cross-section (BII-36), 70skew • 8 beams weight 26 tons and 2 beams weight 32 tons • longitudinal post-tensioning at bottom plate of girder beams • transverse post-tensioning of girder beams at the support sections • 9” of gravel fill equivalent to 7” concrete/asphalt deck

  5. Abutment • Isolation • Bearings • Girder • Beams • Gravel • Spreader • Beam

  6. ashford.wmv

  7. Elastomeric Isolators • Target period of isolated bridge: T=2 sec • Total weight per bearing: W=100 kips • Design deformation: D=4 in • 10 low-damping elastomeric bearings of circular cross-section with two different rubber compounds: • Group A -> G=120 psi -> k=2.7 kips/in • Group B -> G=70 psi -> k=1.6 kips/in • Groups A and B are assigned to each of the two adjacent bridges • Characterization testing of isolation bearings at SEESL/UB in order to acquire mechanical properties

  8. 20091015-MOV0DF.mpg

  9. Bearing Characterization at SEESL • Group A • kA=2.5 kips/in • ζA=5% • Group B • kB=1.5 kips/in • ζB=3%

  10. Full-Scale Bridge Testing • Actuator spans the gap between the two adjacent single span bridges • Slow extension rate of the actuator up to: • 16” to the reaction load cell • 4” design displacement of the bearings • Fast retraction rate of the actuator in order to subject the two bridges in free vibration • Actuator Load Cell

  11. Group A Group B F=24kips 2.4 in 4.0 in • Forcing System Properties: • Max actuator stroke: 24 in • Max actuator force: 50 kips F=24kips

  12. Group A • initial displacement: 2.4 in • damping: 5% • period: 2.0 sec • free vibration duration: 35 sec • number of cycles: 15 • Group B • initial displacement: 4 in • damping: 3% • period: 2.6 sec • free vibration duration: 70 sec • number of cycles: 25

  13. Testing Procedure • Collect the initial mechanical properties of the isolation bearings (stiffness, damping) • Run bridge free vibration set of tests remotely from SEESL/UB • Collect data/info from: • actuator, reaction load cell • accelerometers, load cells, string potentiometers, thermocouples (26 sensors in total) • cameras • weather station • Obtain post-testing mechanical properties of bearings and compare to pre-testing ones • Visit the bridge field station in order to check condition of bearings, actuator, instrumentation • Repeat the procedure weekly and for a period of five years

  14. System Property Modification Factors • Properties of seismic isolation bearings: • Characteristic strength, Qd • Effective stiffness, Keff • Post-yield stiffness, Kd • Damping ratio, ζ • Phenomena effecting isolator properties: • Temperature • Aging • Wear or Travel • History of loading • Which are the max and min probable values of the bearing properties within the structure’s lifetime? • Can all phenomena occur simultaneously?

  15. Pmax = λmax·Pn • Pmin = λmin·Pn • Pn • λmax= λmax,1·λmax,2·λmax,3··· • λmin= λmin,1·λmin,2·λmin,3··· • Bounding • Analysis • λ-factors: quantify the effect of a particular phenomenon on the nominal properties of an isolation bearing • Pmax controls the substructure and superstructure force response • Pmin controls the isolator displacement response • System Property Adjustment factors account for the probability that several events occur simultaneously, depend on the significance of the structure and their values are based on engineering judgment • According to AASHTO (1999): • “The λ-factors listed herein are based on the available limited data. In some cases the factors could not be established and need to be determined by test.”

  16. Temperatures for design: 700F to -220F (AASHTO, 1999) • Low temperatures cause increase in stiffness and strength • Duration of exposure is significant but usually neglected • Travel or Wear due to traffic and temperature changes: • For a cumulative movement of 1 mile 17 sets of free vibration tests should be conducted during one day of testing (AASHTO, 1999) • λ-factors depend significantly on the rubber compound of the bearing λ-factors for Elastomeric Bearings • λmax,t • λmax,tr • max: 800 to 1000F • min: -300 to 100F

  17. Conclusions • Better understanding of the effect of temperature, environmental conditions and ware on the mechanical properties of isolation bearings • Realistic determination of bounding values of isolator properties for analysis and design based on better estimated Property Modification Factors • Using different seismic isolation systems the bridge field station can provide an insight to the resilience of bridges due to naturally-occurring phenomena

  18. Acknowledgments • SEESL technical staff and students • Doug Stryker and Andrew Dailey from Calspan • H&K Services for constructing the bridge • Hubbell Galvanizing for donating the girder beams • Dynamic Isolation Systems for providing the bearings

  19. Thank you! Questions?

  20. Instrumentation/DAQ System • actuator displacement, load cell sensors • 26 sensors: • 10 accelerometers • 2 load cells (temperature range -10F – 100F) • 10 string potentiometers • 4 thermocouples • 7 digital cameras • 1 digital weather station • 32-channel portable DAQ System compatible with existing UB/NEES systems and software SEESL remote desktop controller internet Ashford hostPC/ Pump controller Actuator/Test SEESL remote desktop DAQ internet Ashford hostPC DAQ/Sensors

  21. Wear or Cumulative Travel • Temperature: • low temperatures -> increase in stiffness and strength • high temperatures -> degradation of the rubber • Coupling between wear and temperature • Duration of exposure and elastomeric compound control behavior • Lack of long-term in-situ performance data Effects on Elastomeric Bearings • max: 80 to 100F • min: -30 to 10F

More Related