1 / 28

Introduction to Process Control

Chapter One. Introduction to Process Control. control element. controller. process. sensor. Control Terminology. Controlled Variables - These are the variables which quantify the performance or quality of the final product, which are also called output variables .

erickey
Download Presentation

Introduction to Process Control

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Chapter One Introduction to Process Control

  2. control element controller process sensor

  3. Control Terminology Controlled Variables - These are the variables which quantify the performance or quality of the final product, which are also called output variables. Manipulated Variables - These input variables are adjusted dynamically to keep the controlled variables at their set-points. Disturbances - These are also called the “load” variables and represent inputs that can cause the controlled variables to deviate from their respective set points.

  4. Control Terminology Servo control - The set-point signal is changed and the manipulated variable is adjusted appropriately to achieve the new operating conditions. Regulatory control – The set-point is fixed at a constant value. When any disturbance enters the system, the manipulated variable is adjusted to drive the controlled variable back to its fixed set-point.

  5. Chapter 1

  6. Why do we need automatic process control? • Industrial processes are not static but rather very dynamic; they are continuously changing as a result of many types of disturbances. • It is principally because of this dynamic nature that control systems are needed to continuously and automatically watch over the variables that must be controlled.

  7. Illustrative Example: Blending System • Notation: • w1, w2 and w are mass flow rates • x1, x2 and x are mass fractions of component A

  8. Assumptions: • w1 is constant • x2 = constant = 1 (stream 2 is pure A) • Perfect mixing in the tank Control Objective: Keep x at a desired value (or “set point”) xsp, by adjusting flow rate w2, despite variations in x1.. • Terminology: • Controlled variable (or “output variable”): x • Manipulated variable (or “input variable”): w2 • Disturbance variable (or “load variable”): x1

  9. Design Question: What value of is required to have Overall balance: Component balance: (The overbars denote nominal steady-state design values.) • At the design conditions, . Substitute Eq. (1), and , then solve Eq. (2) for :

  10. Control Question Suppose that the inlet concentration changes with time. How can we ensure that x remains at or near the set point ? As a specific example, if and , then .

  11. Possible Control Strategies Method 1. Measure x and adjust w2. Intuitively, if x is too high, we should reduce w2 and vice versa. • Manual control • Automatic control with proportional feedback control law.

  12. Method 2. Measure x1 and adjust w2. Thus, if x1 is greater than , we would decrease w2 so that One approach: Consider Eq. (3) and replace and with x1(t) and w2(t) to get a control law: Because Eq. (3) applies only at steady state, it is not clear how effective the control law in (5) will be for transient conditions.

  13. Method 3.Measure x1 and x, adjust w2. • This approach is a combination of Methods 1 and 2. • Method 4. Use a larger tank. • If a larger tank is used, fluctuations in x1 will tend to be damped out due to the larger capacitance of the tank contents. • However, a larger tank means an increased capital cost.

  14. Classification of Control Strategies

  15. Feedback Control • Distinguishing feature: • measure the controlled variable. • It is important to make a distinction between negative feedback and positive feedback. • Advantages: • Corrective action is taken regardless of the source of the disturbance. • Reduces sensitivity of the controlled variable to disturbances and changes in the process (shown later). • Disadvantages: • No corrective action occurs until after the disturbance has upset the process, that is, until after x differs from xsp. • Very oscillatory responses, or even instability

  16. Feed Forward Control • Distinguishing Feature: Measure a disturbance. • Advantage: Correct for disturbance before it upsets the process. • Disadvantage: • Must be able to measure the disturbance • No corrective action for unmeasured disturbances.

  17. Justification of Process Control • Increased product throughput • Increased yield of higher valued products • Decreased energy consumption • Decreased pollution • Decreased off-spec product • Increased Safety • Extended life of equipment • Improved Operability • Decreased production labor

  18. Economic Incentives - Advanced Control

  19. Figure 1.7 Hierarchy of process control activities.

  20. Figure 1.9 Major steps in control system development

More Related