Electromagnetism

1. Electromagnetism http://www.windpower.org/en/stat/emag/emagn.htm

2. Electromagnetism • The current magnetizes the iron core and creates a pair of magnetic poles, one North, and the other South. • The two compass needles consequently point in opposite directions.

4. Induction • The light bulb flashes the moment you connect the switch to the battery. • The explanation is, that the magnetic field coming from the upper electromagnet flows through the lower iron core. • The change in that magnetic field, in turn induces an electric current in the lower coil. • The current in the lower coil ceases once the magnetic field has stabilized. • If you switch off the current , you get another flash, because the magnetic field disappears. The change in the field induces another current in the lower core, and makes the light bulb flash again.

5. Simple AC Generator Source: http://www.tpub.com/content/doe/h1011v3/css/h1011v3_111.htm

6. Simple AC Generator • In   this   type   of generator, a DC source is supplied to  the rotating  field  coils. • This produces  a  magnetic  field  around the rotating element. • As the rotor is turned by the prime mover, the magnetic field will cut the conductors of the stationary  armature,  and  an  EMF will be induced into the armature windings.

7. Alternating Current • With an alternating current in the electrical grid, the current changes direction very rapidly, as illustrated on the graph above. • Ordinary household current in most of the world is 230 Volts alternating current with 50 cycles per second = 50 Hz • "Hertz" named after the German Physicist H.R. Hertz (1857-1894). • The number of cycles per second is also called the frequency of the grid. • In USA household current is 130 volts with 60 cycles per second (60 Hz).

8. Phase Anglehttp://www.windpower.org/en/stat/unitsac.htm • Since the voltage in an alternating current system keeps oscillating up and down one cannot connect a generator safely to the grid, unless the current from the generator oscillates with exactly the same frequency, and is exactly "in step" with the grid, • i.e. that the timing of the voltage cycles from the generator coincides exactly with those of the grid. • Being "in step" with the grid is normally called being in phase with the grid. • If the currents are not in phase, there will be a huge power surge which will result in huge sparks, and ultimately damage to the circuit breaker (the switch), and/or the generator. • In other words, connecting two live AC lines is a bit like jumping onto a moving seesaw. • If you do not have exactly the same speed and direction as the seesaw, both you and the people on the seesaw are likely to get hurt.

9. Stationary Armature 3 Phase Generator

10. Three-Phase AC Generators • The principles of a three-phase generator are basically the  same as  that of  a single-phase  generator. • There are three equally-spaced windings and three output  voltages.   • These  are  all  120°  out  of phase  with one another.

11. Connecting a 3 Phase Generator to the Network

12. Phase Anglehttp://www.windpower.org/en/stat/unitsac.htm • Since the voltage in an alternating current system keeps oscillating up and down you cannot connect a generator safely to the grid, unless the current from the generator oscillates with exactly the same frequency, and is exactly "in step" with the grid, • i.e. that the timing of the voltage cycles from the generator coincides exactly with those of the grid. Being "in step" with the grid is normally called being in phase with the grid. • If the currents are not in phase, there will be a huge power surge which will result in huge sparks, and ultimately damage to the circuit breaker (the switch), and/or the generator. • In other words, connecting two live AC lines is a bit like jumping onto a moving seesaw. • If you do not have exactly the same speed and direction as the seesaw, both you and the people on the seesaw are likely to get hurt.

13. Power Quality • The term "power quality" refers to the voltage stability, frequency stability, and the absence of various forms of electrical noise (e.g. flicker or harmonic distortion) on the electrical grid. • More broadly speaking, power companies (and their customers) prefer an alternating current with a nice sinusoidal shape.

14. Starting and Stopping • Most electronic wind turbine controllers are programmed to let the turbine run idle without grid connection at low wind speeds. • If it were connected to the grid at low wind speeds, energy will flow from the grid to the turbine and it would run as a motor. • The motor may over-speed and be damaged. • There are several safety devices, including fail-safe brakes, in case the correct start procedure fails. • Once the wind becomes powerful enough to turn the rotor and generator at their rated speed, the turbine generator becomes connected to the electrical grid at the right moment. • This is done using electrical controllers.

15. Effects of Sudden Starts • If you switched a large wind turbine on to the grid with a normal switch, the neighbors would initially see a brownout • This is because of the current required to magnetize the generator. • This is followed by a power peak due to the generator current surging into the grid. • Another unpleasant side effect of using a "hard" switch would be to put a lot of extra wear on the gearbox, since the cut-in of the generator would work as if you all of a sudden slammed on the mechanical brake of the turbine.

16. Soft Starting with Thyristors • To prevent this situation, modern wind turbines are soft starting. • They connect and disconnect gradually to the grid using thyristors, a type of semiconductor continuous switches which may be controlled electronically. • You may in fact have a thyristor in your own home, if you own a modern light dimmer, where you can adjust the voltage on your lamps continuously. • Thyristors waste about 1 to 2 per cent of the energy running through them. • Modern wind turbines are therefore normally equipped with a so called bypass switch, i.e. a mechanical switch • This is activated after the turbine has been soft started, and the thyristor is bypassed.

17. Power Quality issues:Weak Grids • If a turbine is connected to a weak electrical grid, (i.e. it is vary far away in a remote corner of the electrical grid with a low power-carrying ability), there may be some brownout / power surge problems of the sort mentioned above. • In such cases it may be necessary to reinforce the grid, in order to carry the fluctuating current from the wind turbine. • Local power companies have experience in dealing with these potential problems, because they are the exact mirror-image of connecting a large electricity user, (e.g. a factory with large electrical motors) to the grid.

18. Power Quality Issues: Flicker • Flicker is an engineering expression for short lived voltage variations in the electrical grid which may cause light bulbs to flicker. • This phenomenon may be occur if a wind turbine is connected to a weak grid, since short-lived wind variations will cause variations in power output. • There are various ways of dealing with this issue in the design of the turbine: • mechanically, electrically, and using power electronics

19. Power Quality issues: Islanding • Islanding is a situation which may occur if a section of the electrical grid becomes disconnected from the main electrical grid, e.g. because of accidental or intended tripping of a large circuit breaker in the grid (e.g. due to lightning strikes or short circuits in the grid). • If wind turbines keep on running in the isolated part of the grid, then it is very likely that the two separate grids will not be in phase after a short while. • Once the connection to the main grid is re-established it may cause huge current surges in the grid and the wind turbine generator. • It would also cause a large release of energy in the mechanical drive train (i.e. the shafts, the gear box and the rotor of the wind turbine) much like "hard switching" the turbine generator onto the grid would do. • The electronic controller of the wind turbine will therefore constantly have to monitor the voltage and frequency of the alternating current in the grid. • In case the voltage or frequency of the local grid drift outside certain limits within a fraction of a second, the turbine will automatically disconnect from the grid, and stop itself immediately afterwards. • Normally by activating the aerodynamic brakes