1 / 35

OBJ009302 MA5300 Broadband Access Equipment Troubleshooting

OBJ009302 MA5300 Broadband Access Equipment Troubleshooting. 1.0. Objectives. Master basic troubleshooting methods. Use the commonly used commands to identify the problems. To solve the common service faults in MA5300. Upon Completion of this course, you will be able to:. Contents.

fairly
Download Presentation

OBJ009302 MA5300 Broadband Access Equipment Troubleshooting

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. OBJ009302 MA5300 Broadband Access Equipment Troubleshooting 1.0

  2. Objectives • Master basic troubleshooting methods. • Use the commonly used commands to identify the problems. • To solve the common service faults in MA5300. Upon Completion of this course, you will be able to: Security Level: Internal

  3. Contents Some Ideas in Troubleshooting How to Troubleshoot in MA5300 Service Troubleshooting in MA5300 Security Level: Internal

  4. Some Ideas in Troubleshooting General procedure of troubleshooting. • Recognizing Symptoms • Understanding the Problem • Identifying Cause of the Problem • Solving the Problem Security Level: Internal

  5. Some Ideas in Troubleshooting Common methods in troubleshooting: • Layer-based analysis • Isolation analysis • Comparison analysis • Swapping analysis Security Level: Internal

  6. Layer-based Analysis Application Presentation Session Transport Destination unreachable, … Network PVC, VLAN, PPP link fail… Data Link Cable fail, board fail, cable disconnected… Physical Security Level: Internal

  7. IP Network Isolation Analysis DHCP Server Radius Server DSLAM BAS VDSL Modem Security Level: Internal

  8. Comparison Analysis MA5300(Built-in BAS) ….. Ordinary subscribers Ordinary subscribers Commercial subscribers Commercial subscribers Ordinary subscribers Commercial subscribers Ordinary subscribers Security Level: Internal

  9. IP Network Swapping Analysis FTP Server DHCP Server Radius Server Low Speed DSLAM BAS VDSL Modem Swap Component Security Level: Internal

  10. Troubleshooting Tools Common tools used in troubleshooting: • Command Line • NMS • Network analyzer (Ethereal, Sniffer, Analyzer…) Security Level: Internal

  11. Contents Some Ideas in Troubleshooting How to Troubleshoot in MA5300 Service Troubleshooting in MA5300 Security Level: Internal

  12. Physical Layer Troubleshooting Indicator Modem: ADSL line sync, Ethernet state Board: RUN, ALARM Interface: State, Data Security Level: Internal

  13. Physical Layer Troubleshooting Alarm [BAS]display trap Display trap buffer: # [02/23/2004 23:57:33-] DEV-2-070f2004:frame 0 slot 0 subslot 0 port 10 up …… MA5300(config)#show alarm list all ALARMID OUTPUT STATISTIC ALARM_NAME 0x00200000 YES NO 15-minute threshold alarm 0x00200001 YES NO 24-hour threshold alarm 0x02300003 YES NO Clock SDH source switch Security Level: Internal

  14. Physical Layer Troubleshooting Display state of the interface. [bas1-for-nms]display interface Ethernet 5 Ethernet5 current state : DOWN Line protocol current state : DOWN Description : HUAWEI, ISU, Ethernet5 Interface The Maximum Transmit Unit is 1500, The keepalive is 10(sec) … MA5300(config)#show interface adsl 0/0/0 Adsl0/0/0 is administratively down The ADSL link is deactive Bind line-profile No.1 LINE-PROFILE-1 Bind alarm-profile No.1 ALARM-PROFILE-1 … Security Level: Internal

  15. Physical Layer Troubleshooting Display working state of the board MA5300(config)#show board 0 SlotID BoardName Status SubType1 SubType2 0 EADA Normal 1 2 3 4 5 6 7 ESMA Active_normal O2GAE E4FE 8 ESMA Standby_normal O2GAE E4FE Security Level: Internal

  16. Physical Layer Troubleshooting ADSL line condition MA5300(config)#show adsl line state adsl 0/0/0 Current Link Status : deactive Atuc Current Snr Margin(dB) : 0 Current Chan Attenuation(dB) : 0 Current Output Power(dBm) : 0 Current Attainable Rate(Kbps) : 0 Current Transmission Mode : NONE Channel Interleave Delay(ms) : 0 Channel Current tx-Rate(Kbps) : 0 Atur … Security Level: Internal

  17. Data Link Layer Troubleshooting Check working mode of Modem Check the pvc configuraiton MA5300(config)#show interface adsl 0/0/0 Adsl0/0/0 is administratively down The ADSL link is deactive Bind line-profile No.1 LINE-PROFILE-1 Bind alarm-profile No.1 ALARM-PROFILE-1 Line coding type is DMT Local-Tx-Rate 0 Kbps, Remote-Tx-Rate 0 Kbps, _ADSL_TX …… PVC: vpi is 0, vci is 35 …… Security Level: Internal

  18. Data Link Layer Troubleshooting Check the VLAN configuration MA5300(config)#show vlan Now, the following vlan exist(s): 1(default), 99, 128-175 MA5300(config)#show interface adsl 0/0/0 Adsl0/0/0 is administratively down The ADSL link is deactive …… PVID is 128 …… Port mode: access Tagged VLAN ID : none Untagged VLAN ID : 128 Security Level: Internal

  19. Data Link Layer Troubleshooting MA5300(config)#show interface gigabitEthernet 7/1/1 GigabitEthernet7/1/1 is up Hardware is Gigabit Ethernet, Hardware address is 00e0.fc1e.efc9 ……. PVID is 1 Priority is 0 Max multicast group count: 2 Port mode: trunk Vlan passing : 1(default vlan), 99 Vlan allowed : 1(default vlan), 2-4000 Security Level: Internal

  20. Network Layer Troubleshooting Check IP configuration of the customer’s computer. Display interface state [BAS]display interface GigabitEthernet 10 GigabitEthernet10 current state : UP Line protocol current state : UP Description : HUAWEI, ISU, GigabitEthernet10 Interface …… Ping MA5300#ping 172.31.1.53 Security Level: Internal

  21. Network Layer Troubleshooting Check IP route <BAS>display ip routing-table Routing Table: public net Destination/Mask Proto Pre Cost Nexthop Interface 127.0.0.0/8 DIRECT 1 0 127.0.0.1 InLoopBack0 127.0.0.1/32 DIRECT 1 0 127.0.0.1 InLoopBack0 MA5300(config)#show ip route Routing Tables: Destination/Mask Proto Pre Metric Nexthop Interface 127.0.0.0/8 DIRECT 0 0 127.0.0.1 InLoopBack0 172.31.1.0/24 DIRECT 0 0 172.31.1.52 Vlan-interface99 Security Level: Internal

  22. Network Layer Troubleshooting Debug <BAS>terminal monitor <BAS>terminal debugging <BAS>debugging dhcpr packet Trace <BAS>trace object ? ethernet Object ethernet number gigabitethernet Object ethernet number ip-address Object ip address mac-address Object mac address trunk Object trunk number user-name Object user name Security Level: Internal

  23. Contents Some Ideas in Troubleshooting How to Troubleshoot in MA5300 Service Troubleshooting in MA5300 Security Level: Internal

  24. PPPoE Service Troubleshooting Common service problems in MA5300: • User cannot find the PPPoE server. • Username or password is incorrect. • Low speed. Security Level: Internal

  25. PPPoE Service Troubleshooting User cannot find the PPPoE server. Cause: The PPPoE client cannot find the PPPoE server. Locating problem:Physical layer, or data link layer. Solving problems: [User] • Check the PPPoE client was installed correctly; • Check the Physical connection between computer and modem, modem and the phone line; • Check modem was configured correctly; Security Level: Internal

  26. PPPoE Service Troubleshooting [DSLAM] • Check the EAD board state, and the ADSL line state; • Check the connection between DLSAM and BAS; • Check the vpi/vci of the ADSL port; • Check the VLAN configuration in DSLAM; ADSL port and uplink ethernet port. [BAS] • Check the PPPoE configuration in BAS. Virtual-template and whether the port is bound with VT. Security Level: Internal

  27. PPPoE Service Troubleshooting Username or password is incorrect. Cause: user cannot pass authentication. Locatingproblem: PPP link layer, network layer. Physical layer works. Physical layer is working normally. Solving problems: [User] • Confirm the user input correct username and password; [BAS] • Check the authentication configuration in BAS, whether the user uses local authentication or Radius authentication. Security Level: Internal

  28. PPPoE Service Troubleshooting • If the user uses local authentication, check whether this username and password was configured in the BAS correctly. • If the user uses Radius authentication, check the Radius configuration. [External equipment] • Check the Radius server is working normally, and is reachable. • Check the username and password was configured in the Radius correctly. Security Level: Internal

  29. PPPoE Service Troubleshooting Low speed. Solving problems: [User] • Check the user’s computer’s hardware configuration, and running performance. • Check the cable and line is fully connected. [DSLAM] • Check the quality of the ADSL line • Check the transmission rate configuration of the ADSL line profile. Security Level: Internal

  30. PPPoE Service Troubleshooting [BAS] • Check the CAR configuration of the user. • Ping destination IP address to see whether there is a traffic bottleneck to the destination in network. • If possible, connect a server directly with BAS, observe the traffic on the user’s computer. Security Level: Internal

  31. DHCP Service Troubleshooting User cannot obtain IP address. Locating problem:physical layer, data link layer, network layer. Solving problem: [User]: • Check the IP configuration of the computer. • Check the Physical connection between computer and modem, modem and the phone line; • Check modem was configured correctly; Security Level: Internal

  32. DHCP Service Troubleshooting [DSLAM] • Check the EAD board state, and the ADSL line state; • Check the connection between DLSAM and BAS; • Check the vpi/vci of the ADSL port; • Check the VLAN configuration in DSLAM; [BAS] • Check the service configuration. • If the external DHCP is used, check the DHCP server is working normally and reachable. Security Level: Internal

  33. DHCP Service Troubleshooting [External equipment] • Make sure the configuration in DHCP server is correct. Security Level: Internal

  34. DHCP Service Troubleshooting Low speed. • Same as PPPoE service. Security Level: Internal

  35. Thank you Security Level: Internal

More Related