1 / 14

MUST HAVE

MUST HAVE. SHOULD HAVE. COULD HAVE. Module # 140. Practical Class Exercise’s, 2 nd session. Objectives: Know how to: Setup a Flowmeter add Channel based on a Flowmeter Add and configure a Flowmeter based MP Add and configure LIW MP Add and configure Dump to Empty MP

fredricka-elijah
Download Presentation

MUST HAVE

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. MUST HAVE SHOULD HAVE COULD HAVE Module # 140

  2. Practical Class Exercise’s, 2nd session • Objectives: • Know how to: • Setup a Flowmeter • add Channel based on a Flowmeter • Add and configure a Flowmeter based MP • Add and configure LIW MP • Add and configure Dump to Empty MP • Use the above Material Paths to do Feeds • Reference: Qi Technical manual.doc • Ch 3 – Flowmeter program block • Ch 4 – Flowmeter • Ch 4 – Assign Channels • Ch 4 – Configure Material Paths

  3. Class Exercise #1 – Setup a Flowmeter • Via the Flowmeter Button Configure Flowmeter (K) • Verify Flowmeter is functioning • How ? :Switch to the Flowmeter Channel and manually add water, check to see that the Qi display is counting. • Via the PAC Button Add a Flowmeter based Channel, use Channel 3 • Reference: Qi Technical manual.doc • Ch 3 – Flowmeter program block • Ch 4 – Flowmeter • Refer to next slides after your own attempt.

  4. A Configured Flow meter • A correctly configured Flow meter example

  5. Example of Flowmeter based Channel • Note: Some parameters are Instrument capacity dependent

  6. Class Exercise #2 • Add MP2, GIW & SPILL only • PAC >> Material Paths • Enter required MP number • Configure all Parameters • TIP: Save this page as : “Defaults” then this page can be loaded and edited • Do some Feeds using this Material Path (refer Module 090) • Check that Feeds are error free with a green screen • Example follows on next slide. Try on Own first

  7. A Configured MP2

  8. Class Exercise #3 • Add MP3, LIW & Dump to Empty • PAC >> Material Paths • Enter required MP number • Configure all Parameters • TIP: load previously saved “Defaults” and edit • Do some Feeds using this Material Path (refer Module 090) • Check that Feeds are error free with a green screen • Example follows on next slide. Try on Own first

  9. A Configured MP3

  10. Class Exercise #4 • Add MP4, LIW & K1 • PAC >> Material Paths • Enter required MP number • Configure all Parameters • TIP: load previously saved “Defaults” and edit • Do some Feeds using this Material Path (refer Module 090) • Check that Feeds are error free with a green screen • Example follows on next slide. Try on Own first

  11. A Configured MP4

  12. Class Exercise #5 • Add MP7, GIW use (Flowmeter as the channel) • PAC >> Material Paths • Enter required MP number • Configure all Parameters • TIP: load previously saved “Defaults” and edit • Do some Feeds using this Material Path (refer Module 090) • Check that Feeds are error free with a green screen • Example follows on next slide. Try on Own first

  13. A Configured MP7

  14. Review Questions • Can you add a Material Path while still in “Run Mode” ? • Can you edit a Material Path while still in “Run Mode” ? • What are the Four Material Path “Feeder Types” ? • Bonus Questions • What is the meaning of the “Assembly Slot” number that is found on the Channel Setup Page? ? • Can it be edited

More Related