1 / 36

8086 [2]

8086 [2]. Ahad. Internal! . External ?. 8086 vs 8088. Only external bus of 8088 is 8bit. 8_bit Data Bus 20_bit Address. 16_bit Data Bus 20_bit Address. 8088. 8086. Pin configuration:. 8086/8088 Busses. Address Bus 20 address lines so a 2 20 byte address space.

gwen
Download Presentation

8086 [2]

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. 8086 [2] Ahad

  2. Internal!

  3. External?

  4. 8086 vs 8088 Only external bus of 8088 is 8bit 8_bit Data Bus 20_bit Address 16_bit Data Bus 20_bit Address 8088 8086

  5. Pin configuration:

  6. 8086/8088 Busses • Address Bus • 20 address lines so a 220 byte address space. • Pins A0-A19 provide the address • For 8086, A0-A15 are multiplexed with D0-D15 to form AD0-AD15 • For 8088, A0-A7 are multiplexed with D0-D7 to form AD0-AD7 • Data Bus • For 8086, 16 bit data bus D0-D15 (multiplexed as AD0-AD15) • For 8088, 8 bit data bus D0-D7 (multiplexed as AD0-AD7)

  7. Control pins • Control Bus • For memory access, the following pins are used: RD’, WR’, M/IO’, DT/R’, DEN’, ALE, BHE’ • Other input signals to control 8086 performance: clk ,reset , ready , hold , test’, intr , nmi ,mn’/mx - The intrandholdare acknowledged throughintraandholdarespectively.

  8. 8086 Pin Assignment

  9. 8086 Pin Description Vcc(pin 40) : Power supply input GND(pin 1 and 20) : Ground pin is the return of the power supply

  10. AD0…AD7, A8...A15 , A19/S6, A18/S5, A17/S4, A16/S3 : 20-bit Address Bus When ALE=1 [Address Latch Enable]  AD8-AD15 becomes address bits. When ALE=0 it becomes data bits.

  11. A19/S6, A18/S5, A17/S4, A16/S3 Address/status bus - S4 S3 function . 0 0 extra segment 0 1 stack segment 1 0 code or no segment 1 1 data segment  These two status bits could be used to address four separate 1MByte mem banks – by decoding them as A21 and A20 S5  indicates the condition of the IF flag bit S6  always a logic 0

  12. MN/MX’(33, input) : Indicates Operating mode – min mode or max mode

  13. READY (input, Active High) : Takes µP to wait state 0  µP enters into wait states n remains idle. 1  no effect on the operation of the µP

  14. CLK (input) : Provides basic timing for the processor CLK must have a duty cycle of 33% (high for 1/3 of the clocking period & low for 2/3)

  15. DEN’ (output) : activates external data bus buffers. It is LOW when processor wants to receivedata or processor is giving outdata

  16. DT/R’ (output) : Data Transmit/Receive. 1  data from µP to memory 0  data is from memory to µP

  17. M/IO’ (output) : selects mem or I/O. It indicates that the mP address bus contains – either a memory address or an I/O port address. 1  µP access I/O Device 0  µP access memory

  18. RD’ (output) : When Low, µP is performing a read operation 0  the data bus is receptive to data from the mem or I/O devices connected to the system.

  19. WR’ (output) : When Low, µP is performing a write operation It is outputting data to a mem or I/O device. During the time WR=0, the data bus contains a valid data for mem or I/O.

  20. ALE (output) : Address Latch Enable, Active High to latch address 1 µP is using AD0..AD7, A19/S6, A18/S5, A17/S4, A16/S3 as address bus. This address can be a mem address or an I/O port number.

  21. RESET (input, Active High) : At least 4 clock cycles causes the µP immediately terminate its present activity.

  22. TEST’ (input , Active Low) : it is an input pin – that is tested by the WAIT instruction. 0  the WAIT instr. functions as an NOP. 1  the WAIT instr. waits for TEST to become a logic 0.

  23. HOLD (input , Active High) : it requests a DMA [Direct Memory Access] 1  the mP stops executing software and places its address, data, and control bus at the high-impedance state. 0  mP executes SW normally.

  24. HLDA (output , Active High) : Hold Acknowledge – indicates that the mP has entered the HOLD state. INTR (input , Active High) : Interrupt request It is used to request a hardware interrupt. 1  when IF = 1, mP enters an interrupt acknowledge cycle (INTA becomes active) after the current instruction has completed execution. [IF - Interrupt Flag -Set by user to disable hardware interrupts temporarily]

  25. INTA’ (output , Active Low) : Interrupt Acknowledge NMI (input , Active High) : Non-maskable interrupt similar to INTR – except that the NMI interrupt does not check to see whether the IF flag is 1.

  26. The AD0-AD15 lines are a 16-bit multiplexed addressed or data bus. • During the 1st clock cycle, AD0-AD15 are the low order 16-bit address. • The 8086 has a total of 20 address line, the upper 4 lines are multiplexed with the state signal that isA16/S3, A17/S4, A18/S5, A19/S6. • For memory and i/o operations, AD15-AD0 contain the 16 bit data and S3,S4,S5,S6 become the status line.

  27. BHE/S7 is used as best high enable during the 1stclock cycle of an instruction execution. • BHEcan be used in conjunction with AD0 to select the memory

  28. RD is low when the data is read from memory or I/O location

  29. TEST is an input pin and is only used by the wait instruction • 8086 enters a wait state after execution of the wait instruction until a low is seen on the test pin.

  30. ALE is an address latch enable is an o/p signal provided by the 8086 • - can be used to demultiplexed AD0 to AD15 in to A10 toA15 and D0 to D15.

  31. M/IO is an 8086 output signal to distinguish a memory access and i/o access.

  32. 33. MN/MX • The 8086 can operate in two modes: • minimum mode and • maximum mode For minimum mode, a unique processor system with a single 8086 For maximum mode, a multi-processor system with more than one 8086.

  33. Minimum-Mode and Maximum-Mode System

  34. Signals common to both minimum and maximum mode

  35. Minimum-Mode and Maximum-Mode System (cont.) Unique minimum-mode signals

  36. Minimum-Mode and Maximum-Mode System (cont.) Unique maximum-mode signals

More Related