540 likes | 1.39k Views
Resistivity and Seebeck measurements. Daniel Harada August 18 2010. I. Resistivity. R contact. R contact. R sample. R contact. R contact. R sample. Resistivity. Two-point probe. Four-point probe. Measures sample only. Measures sample + contact resistance + probe resistance.
E N D
Resistivity and Seebeck measurements Daniel Harada August 18 2010
I Resistivity
Rcontact Rcontact Rsample Rcontact Rcontact Rsample Resistivity Two-point probe Four-point probe Measures sample only Measures sample + contact resistance + probe resistance In four-point probe, negligible current flows through the voltmeter, the only voltage drop measured is across Rsample.
Rcontact Rcontact Rsample Rcontact Rcontact Rsample Resistivity Two-point probe Four-point probe Measures sample only Measures sample + contact resistance + probe resistance
d s t D Collinear Contacts Typical pellet and contact sizes for collinear contacts d = 1 mm s = 2 mm t = 1-2 mm D = 12.7 mm
Collinear contacts F corrects for sample thickness, sample diameter, edge effects, and temperature.
Collinear contacts For samples thinner than the probe spacing s, F can be written as a product of three independent correction factors. • F1corrects for sample thickness • F2corrects for lateral sample dimensions • F3corrects for placement of probes near edges
Collinear contacts For non-conducting substrates: For conducting substrates replace sinh with cosh.
Collinear contacts F11 is for non-conducting substrates F22is for conducting substrates t/s for pellets ~0.75 - 1 F11 ~0.4 – 0.6
Collinear contacts For circular wafers of diameter D: D/s ~ 6 F2 ~ 0.8
Collinear contacts F3accounts for contacts placed near sample edges conducting substrates Parallel: d/s~ 1.7 F31~ 0.9 Perpendicular: d/s~ 3 F32~ 1 non-conducting substrates
Van der Pauw method Van der Pauw found a method to determine the resistivity of an arbitrarily shaped sample subject to the following conditions: a)the contacts are at the circumference of the sample b) the contacts are infinitely small (point contacts) c) the sample has uniform thickness d) the surface of the sample is singly connected, i.e., the sample does not have isolated holes
Van der Pauw method #4 #1 #2 #3
Van der Pauw method f must satisfy the relation: For symmetric contacts f = 1
Van der Pauw method The previous equations were formulated assuming that contacts are point contacts. For contacts of finite size d on a circular disc of diameter D with d/D << 1, the percent increase in resistivity per contact can be found: van der Pauw, Philips Research Reports 13 pg. 1-9 for d/D ~ 0.08 Δρ/ρ ~ -0.000559 total change for 4 contacts ~-0.224%
Porosity Correction Pressed pellets are generally not going to achieve full theoretical density, and thus will contain non-conducting pores which will increase the measured conductivity. Our cold pressed pellets are typically ~80% of theoretical density. Two models that are used to correct for porosity are the Bruggeman Effective Media model, and Minimal Solid Area.
Porosity Correction The effective media model is discussed by McLachlan, Blaszkiewicz, and Newnham. For a pellet 90% dense or higher, it gives a correction factor of: where f is the volume fraction of spherical pores. At 90% dense this gives a correction of 0.85. D. McLachlan, M. Blaszkiewicz, R. Newnham. Electrical Resistivity of Composites. Journal of the American Ceramic Society, 73 (8) 2187-2203 (1990)
Porosity Correction The Minimal Solid Area model was presented by Rice. It assumes that fluxes through a medium will be limited by the smallest cross sectional area they pass through. This model gives a correction of: where b is a factor that depends on the type of pores contained in the medium. R. Rice. Evaluation and extension of physical property-porosity models based on minimum solid area. Journal of Materials Science, 31 102-118 (1996)
Porosity Correction For spherical pores, b = 3, giving a correction factor of ~0.55 for 80% dense pellets. This model will give reasonable results for pellets ~70% dense and higher. This is the model that will typically be used as our pellets are not dense enough to use the Bruggeman model.
Resistivity Summary Collinear contacts: Van der Pauw contacts: Contact correction is negligible F1 ~0.4 – 0.6 F2 ~ 0.8 F3~ 0.9 Porosity correction = e-3f All equations and plots taken from Semiconductor Material and Device Characterization Third ed. by D.K. Schroder, unless otherwise noted.
Seebeck measurements Thermoelectric effect: When a temperature gradient is maintained across a material, a voltage arises. V≠0 TH TC I Seebeck effect: When two dissimilar conductors are joined together, and their junctions are held at different temperatures, a current flows. TH TC
Seebeck measurements n-type material in thermal equilibrium: - - - - - - - - - - - - nleft = nright Tleft= Tright
Seebeck measurements apply a temperature gradient: - - - - - - TH - - - - TC - - - - - - - - - nleft > nright Tleft> Tright
Seebeck measurements free carriers diffuse from high concentration to low, leaving a net charge: + - + - - - TH + - - - TC - - + + - - - - - nleft = nright Tleft> Tright
Seebeck measurements TC TH If S(T) does not vary much with temperature, then: - + VS S should be negative for n-type materials