1 / 25

Outline Damage threshold estimate Test setup pictures, block diagram,… DSA measurements

ERL Differential Current System Status Peter Cameron with contributions from Michelle Wilinski and Christophe DeFrance (Bergoz) 17 Sep 07. Outline Damage threshold estimate Test setup pictures, block diagram,… DSA measurements Noise floor and DC drift Effect of temperature

jaime-bryant
Download Presentation

Outline Damage threshold estimate Test setup pictures, block diagram,… DSA measurements

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. ERL Differential Current System StatusPeter Cameronwith contributions from Michelle Wilinski and Christophe DeFrance (Bergoz)17 Sep 07

  2. Outline • Damage threshold estimate • Test setup pictures, block diagram,… • DSA measurements • Noise floor and DC drift • Effect of temperature • Conclusions from DSA measurements • FPGA measurements • Block diagram • measurement sensitivity • Discussion, conclusions,…

  3. 1 uA-sec (6x1012 electrons, or 1uC) used in the following slides

  4. Agilent FFT box Floppy Bergoz Electronics Excel scope FPGA board ethernet Bergoz Electronics LabVIEW signal generator Test Setup Block Diagram

  5. Full span (PCT nominal BW is 10KHz) noise spectrum not 1/f !!!

  6. Comparison of single toroid and difference spectra single toroid No averaging difference of the two toroids

  7. Comparison with Bergoz measurement Bergoz – 5 averages (note log scale)

  8. 400Hz BW noise spectra Include spectral shaping in null?

  9. Bergoz – 5 averages (note log scale)

  10. Effect of temperature stabilization

  11. Time/temperature dependence of difference current Out of office ~0.1 nA-sec drift over 160 minutes .01667 uA-sec on 1 minute What happened here??? B field change? 100uA/gauss gives .02 gauss

  12. Zoom on previous slide .0033 uA-sec

  13. Conclusions from DSA Measurements • Toroids meet Bergoz spec in uncontrolled conditions (temperature, magnetic field) of office test environment • Study and optimize proper thermal shielding • Frequent null calibration should not be needed • Slow loss limit should be in the range of 1nA-sec or better • Should be a useful diagnostic • Machine protection • (unprecedented and essential) Halo studies at ~10-6need moveable scrapers? • Need to understand vector averaging (more on this later)

  14. Outline • Damage threshold estimate • Test setup pictures, block diagram,… • DSA measurements • Noise floor and DC drift • Effect of temperature • Conclusions from DSA measurements • FPGA measurements • Block diagram • measurement sensitivity • Discussion, conclusions,…

  15. BPM (also FCT, DCCT, BLM,…) Block Diagram

  16. Test Setup Block Diagram ML403 Bergoz Electronics FPGA wrapper A to D Simulink Signal processing, feedback loop, MPS interface,… ethernet Lab VIEW Bergoz Electronics DIO signal generator DAC null MPS MPS function runs independent of Control System - robustness

  17. Process Variables (machine mode, beam mode,…) Process Variables (beam position,…) BPM Module Embedded processor running vXworks/EPICS A/D FPGA PUE signals x4 or x8 1 sec event Beam permit Laser pre-trigger 9.38MHz RF reference

  18. FPGA board control panel

  19. spectral content of simulated beam loss

  20. Next slide is zoom on this

  21. FPGA-based beam loss measurement (S/N ~same for DSA and FPGA) 1 uA-sec loss signal no loss signal 0 1 2 3 4 5 6 7 8 9 10 Time [minutes]

  22. Comments, conclusions • Consider toroid upgrades for RHIC • Present DCCTs are 5uA/rtHz? • Going to 0.1uA/rtHz would give much more sensitive diagnostic for machine tuning - this is important! • Implementation of DI measurement on FPGA board was straightforward ~2 man-weeks of Joe Mead, 1 man-week of Pete Cameron • Paradox? need to understand vector averaging,… see simulation • Where from here? • Basic system functionality and spec demonstrated • I’m on travel for most of the coming month, then Run 8 • Priority shift to BPM electronics • BPM system • Libera demo box due in any day now (after 3 months of trying to get it) • I’m at ITech (Slovenia) next week to work out details of Libera in ERL • Commercial vendor (the major supplier of demo boards) exploring design and fab of COTS FPGA board to our spec (~$1K vs ~$10K or more for Libera box, and much simpler) • Joe Mead is fabbing 4ch fast digitizer mezzanine for ML403 Hold off on further DI development until next spring?

  23. Suggestions for upcoming meeting agendas • Sep 17th – presentation and discussion of DCCT and differential current status • Sep 24th– presentation and discussion of Profile status • Oct 1st – presentation and discussion of BPM status • Oct 8th – Scrapers and collimators

More Related