1 / 34

實習 5 : HDLAutoassignpin ISE Project Navigator SMIMS FPGA programer veriInstrucment

實習 5 : HDLAutoassignpin ISE Project Navigator SMIMS FPGA programer veriInstrucment. HDLAutoassignpin. Step0 Verilog. ISE. Step1 Open File. 選擇 .v 檔. 1. 選擇 FPGA 型號. 2. 3. 4. Step2 SCDK Mode. 選擇 Pin info For SDK. 1. 2. 前三項打勾. 3. Step3 Assignment. 1. Input 連到 switch

jirair
Download Presentation

實習 5 : HDLAutoassignpin ISE Project Navigator SMIMS FPGA programer veriInstrucment

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. 實習5 :HDLAutoassignpinISE Project Navigator SMIMS FPGA programerveriInstrucment

  2. HDLAutoassignpin

  3. Step0Verilog ISE

  4. Step1Open File 選擇.v檔 1 選擇FPGA型號 2 3 4

  5. Step2SCDK Mode 選擇Pin info For SDK 1 2 前三項打勾 3

  6. Step3Assignment 1 Input連到switch Output連到LED 2

  7. Step4Generate 選擇產生.ucf腳位檔的位置 1 2 按下Generate 成功Generate訊息 3

  8. ISE project Navigator

  9. 建立新專案(1/2) 工作列 ->file -> New Project 專案名稱 專案資料夾

  10. 建立新專案(1/2) FPGA的型號，一定要一樣!

  11. 加入Verilog檔與ucf檔 右鍵按下Add Source 1 2 選擇.ucf和.v檔 3

  12. Compile Implement top module 按右鍵->implement top Module 1 Generate Programing File->按右鍵->run 2

  13. SMIMS FPGA programer

  14. 1 2

  15. VeriInstrument

  16. Step0Open File 1 開新檔案 輸入專案檔名稱 2 選擇.v檔 3 選擇板子型號與FPGA型號 4

  17. Step1 Pin Assignment 2 拖曳I/O元件至虛擬面板 1 點開I/O與pins工具列 3 虛擬面板上的元件

  18. Step1 Pin Assignment 2 直接把pin腳拉進 藍色框框 1 對著元件按右鍵 ->Edit assign pin 完成assign pin 3

  19. Step1 Pin Assignment 完成I/O pins assign 將in0,in1拉入switch 將led0~led4拉入led

  20. Step2Compile 1 2 選擇design module 按下step2. Compile 3 按下Compile 4 完成Compile動作

  21. Step3Program FPGA 按下Step3. Program FPGA 注意:按下step3後FPGA版上LED燈號會閃一下

  22. Step4Run FPGA 1 按下Step4. Run FPGA 2 驗證I/O是否如預期

  23. Step0Open File 1 開新檔案 輸入專案檔名稱 2 選擇.v檔 3 選擇板子型號與FPGA型號 4

  24. Step1 Pin Assignment 2 拖曳I/O元件至虛擬面板 1 點開I/O與pins工具列 3 虛擬面板上的元件

  25. Step1 Pin Assignment 2 直接把pin腳拉進 藍色框框 1 對著元件按右鍵 ->Edit assign pin 完成assign pin 3

  26. Step1 Pin Assignment 完成I/O pins assign 將dout[0]~dout[6]分別拉到SEG[0]~SEG[6]

  27. Step2Compile 1 2 選擇design module 按下step2. Compile 3 按下Compile 4 完成Compile動作

  28. Step2Compile 2 Compile出來的bit檔 按下Open Directory 1

  29. Step3Program FPGA 按下Step3. Program FPGA 注意:按下step3後FPGA版上LED燈號會閃一下

  30. Step4Run FPGA 1 按下Step4. Run FPGA 2 驗證I/O是否如預期

More Related