1 / 30

Research at Northwestern University: End-bearing Micropiles in Dolomite

Research at Northwestern University: End-bearing Micropiles in Dolomite. Outline. Introduction Test section details Axial load test results Axial load distributions Design implications Conclusions. Participants : TCDI-Hayward Baker, Lincolnshire, IL Vulcan Quarry, McCook, IL

macha
Download Presentation

Research at Northwestern University: End-bearing Micropiles in Dolomite

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Research at Northwestern University: End-bearing Micropiles in Dolomite

  2. Outline • Introduction • Test section details • Axial load test results • Axial load distributions • Design implications • Conclusions

  3. Participants: TCDI-Hayward Baker, Lincolnshire, IL Vulcan Quarry, McCook, IL Northwestern University

  4. Objective • To evaluate the axial load transfer characteristics of micropiles embedded in dolomite so that rational design procedures can be developed

  5. Overview: • Axial load tests in Vulcan Quarry • Four test piles with lengths of 0.6, 1.2, 1.8 and 2.4 m • Piles consist of 178-mm-diameter, 13 mm wall thickness, 550 MPa steel casings filled with 38 MPa grout. Roller bit is welded to bottom. • Axial load distribution determined by vibrating wire strain gages on steel, embedment gages in grout and telltale readings • Two piles were extracted to examine grout-steel and grout-rock interfaces

  6. Test piles ~ 1 m Hole cored Pile assembled and placed in hole Pile grouted under low pressure Production piles ~ 30 m long Assembled pile with roller bit attached used to drill hole Left in place and grouted under high pressure Installation procedures

  7. Method fymax (MPa) α β Allowable Load (kN) AASHTO (Service load design) 550 0.4 0.47 2000 Chicago Building Code 200 0.4 0.4(1) 800 Massachusetts Building Code 410 .33(3) 0.4(2) 1400 Allowable stress design: Pallow = α f 'c  Agrout + β  fy x A steel

  8. Vulcan Quarry, McCook, IL.

  9. On site preparation of micropiles

  10. Micropile 1 Micropile 3 Micropile 2

  11. Top - 1 Bottom Top - 2 Bottom Bottom Top - 3 Top -4 Bottom Rock Conditions

  12. Load test frame Reaction anchor transfer beams transfer girder hydraulic jack test pile

  13. Axial load test results

  14. Axial Load vs. Deflection of Micropile 1

  15. Axial Load vs. Deflection for Micropile 2

  16. Axial Load vs. Deflection for Micropile 3

  17. Axial Load vs. Deflection for Micropile 4

  18. Summary of load test results • Pile 1 failed at 2000 KN and 4000 KN on second loading, cumulative tip movement = 10 mm (RQD = 22) • Pile 2 failed 800 KN on first loading and 2000 KN on second loading, cumulative tip movement =25 mm (RQD = 0) • Pile 3 did not fail at 4450 KN, tip movement = 2 mm (RQD = 87) • Pile 4 with soft bottom exhibited a plunging failure at 2000 KN

  19. Axial load distributions • Determining moduli for composite pile – Fellenius (1989) method • Data

  20. Strain Gage Data from Micropile 3

  21. Axial Load Distributions for Micropiles 1 and 3

  22. Axial Load Distribution of Micropile 2

  23. Axial Load Distribution for Micropile 4

  24. Mobilized Side Resistance vs Axial Head Deflection

  25. Summary of load transfer data • No load transfer in upper 1 m – due to low confinement and poor rock quality • Critical interface was steel/grout; verified from visual observations of extracted piles • Shorter piles (1 and 2) were end-bearing; capacity a function of RQD • Pile 4 with soft bottom had an average unit side resistance approximately equal to that of a smooth bar pulled from concrete (3500 kPa)

  26. Computed Observed No. Allowable structural load (kN) Davisson allowable load with FS = 2 (kN) Allowable load for 13 mm movement (kN) (1) (2) (3) 1 1630 880 1380 2000 3800 2 1560 800 1320 400 1200 3 1560 800 1320 >2225 >4450 4 1560 800 1320 1000 not applicable (1) – AASHTO (2) – Chicago Building Code (3) – Massachusetts Building Code

  27. Example: Production pile • Typical length in Chicago: 25 to 30 m • When pile tip moves 2 mm under 4450 KN (like pile 3), design for movements • For 27.5 m long pile: • 12.5 mm deformation – 1350 KN capacity • 25 mm deformation – 2600 KN capacity • Both greater than 800 KN based on Chicago code

  28. Conclusions • Stresses in piles were in excess of those specified in codes without detrimental effects on performance • Steel-grout interface governed axial load transfer behavior along side • No side resistance mobilized in top 1 m of test piles due to low stresses and grout pressures and poor quality rock • Due to relatively high compressibility, allowable axial loads of full-scale piles, founded on competent rock, are determined more rationally from allowable deformation considerations, rather than code-specified allowable stresses.

More Related