1 / 8

Beach Cities Robotics Pneumatics

Beach Cities Robotics Pneumatics. August 12, 2007 Rick Wagner, APM, Redwood I&T Northrop Grumman Corporation. Pneumatics Outline. Why Pneumatics? Fluids Principles Applications Pneumatics General FRC Systems. http://www2.usfirst.org/2007comp/other/2007%20FRC%20Pneumatics%20Manual.pdf.

maddox
Download Presentation

Beach Cities Robotics Pneumatics

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Beach Cities Robotics Pneumatics August 12, 2007 Rick Wagner, APM, Redwood I&T Northrop Grumman Corporation

  2. Pneumatics Outline • Why Pneumatics? • Fluids • Principles • Applications • Pneumatics • General • FRC Systems http://www2.usfirst.org/2007comp/other/2007%20FRC%20Pneumatics%20Manual.pdf

  3. Why Pneumatics? • Weight • Compare the weight of several valves and cylinders to that of the motors, gears, belts, and chains used on some lift mechanisms and you will find the weight comparable, if not much lighter. • Simple to Design • Using pneumatics is much easier than building a motor; gear, chain and sprocket lift mechanism. • Adjustable Force • To adjust the force of the cylinder, all you have to do is adjust the regulator in front of it. The force is equal to the area of the cylinder piston times the pressure. Remember that the valves need at a minimum of 15-30 psi to work properly. • Durable • All of us have problems burning up motors from time to time. You can stall an air cylinder against a load indefinitely and turn off the compressor. These are industrial grade products. • Power • You have the option of using a small 3/4” bore cylinder at 20 psi, which will produce a force of around 9 pounds. If you use a 2” bore cylinder at 60 psi, you can get 180 pounds of force. As you can see, your options are wide open. • Custom Cylinders and a Rotary Actuator • You may order the exact cylinder or rotary actuator you need for the job from Bimba again this year, and get them in a few days via regular UPS. • Last Minute Additions • At the last minute, you can add a cylinder and valve very quickly.

  4. Principles • Fluids • A fluid is a material that will not sustain shear stress • There are two kinds of fluids • Liquids (hydraulics) • Liquids are incompressible (high bulk modulus) • Gases (pneumatics) • Compressible (like a linear spring) • Hydraulics • High forces, enormous power, up to 5,000 psi • Volumetric (position) control • Always leak • Not allowed on FRC robots • Pneumatics • Medium forces • Pressure (force) control • Up to 60 psi on FRC robots

  5. Pneumatics Versus Hydraulics (from Wikipedia) • Advantages of pneumatics • The working fluid is very light in weight so supply hoses are not heavy. • Because the working fluid is (mostly) just air, there is usually no need for a return line for the working fluid and leaks of the working fluid tend not to be messy. • Because air is compressible, the equipment is less likely to be damaged by shock. The air in pneumatics absorbs excessive force, whereas the fluid of hydraulics directly transfers force. • Advantages of hydraulics • Higher energy density owing to the much higher working pressures usually employed. • The hydraulic working fluid is basically incompressible, leading to a minimum of spring action. When hydraulic fluid flow is stopped, the slightest motion of the load releases the pressure on the load; there is no need to "bleed off" pressurised air to release the pressure on the load.

  6. FRC Pneumatic Schematic

  7. Calculations • Force equals pressure times area • Area is the radius of the cylinder squared times pi • For tension side, subtract the area of the shaft • Use pounds per square inch (psi) pressure units and square inches for area • Two positions: retracted and extended • Control valve has two outputs: one for extend, one for retract. • Nothing in between for FRC robots

  8. Installation • BRASS FITTINGS • Parker Hannifin donated all the brass fittings. These are useful where you want to plug a port or plumb from one size port to another. It is important to note that all male threads require Teflon tape to seal properly. Wrap the tape around the fitting, leaving the first two threads free of tape This is because the threads are tapered and the tape may come loose from the first thread or so and clog up one of your valves. It is also preferred to wrap the tape in the same direction as the threads. This will prevent the tape from binding up when screwing in fittings. • QUICK CONNECT FITTINGS • SMC Pneumatics donated the quick connect fittings. These are very easy to use. All you have to do is push the tube into the fitting. Make sure you push the tubing all the way into the fitting. To release the tubing, just push the plastic colored ring in (the release button) and then pull the tubing out. Don’t attempt to pull the tubing without first pushing the release button. The picture below shows a representative example of these fittings but does not include all the ones in the kit.

More Related