1 / 27

Wiring for CAN bus

Wiring for CAN bus. ATLAS DCS. Table of contents. ATLAS DCS. Introduction CAN standards Layout of a standard rack configuration Cable requirements Solutions proposed The rack monitoring board The simulation tool. Introduction. ATLAS DCS. Definition of our CAN bus application.

marnina
Download Presentation

Wiring for CAN bus

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Wiring for CAN bus ATLAS DCS Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  2. Table of contents ATLAS DCS • Introduction • CAN standards • Layout of a standard rack configuration • Cable requirements • Solutions proposed • The rack monitoring board • The simulation tool Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  3. Introduction ATLAS DCS Definition of our CAN bus application Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  4. MAXIMUM CABLE LENGTH The limitation come from : • ELMB supply drop through cables • CAN supply drop through cables • CAN bus limitation (from signal point of view) Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  5. CAN BUS LIMITATION CAN bus length main limitations (from signal point of view) • Signal round-trip delay • Oscillator tolerance between nodes • Signal amplitude drop The two first effects are not discussed during this Presentation. However, as rule of thumb, the following bus line length can be achieved… Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  6. Bit rate / Bus length relation …with CAN bit timing parameters being optimized for maximum propagation delay! Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  7. CAN bus signal • Maximum number of nodes : The maximum number of nodes which can be connected to a network depends on the minimum load resistance a transceiver is able to drive : The PCA82C250 transceiver provide an output drive capability down to a minimum load of 45Ω… … which give a maximum number of 112 nodes for 120Ω termination! Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  8. CAN bus signal • Maximum bus line length Is given by the minimum differential voltage at the receiving node for a dominant bit level. A receiver recognizes a dominant bit if the differential voltage is above 1V. We can use the following diagram to calculate the maximum bus length. Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  9. CAN bus signal From the precedent diagram we can find the following formula : Whoua!! With : ρ is the cable linear resistance → 0.0375 Ω/m for NE06 Vdiff_out_min is the transceiver min. diff. output voltage for a dominant bit level → 1.5V Vth is the dominant state receiver threshold voltage → 1V VSM is a safety margin voltage which can be determined as : K*(Vdiff_out-Vth) With 0≤K≤1 e.g K=0.8 → 0.4V RT is the termination resistance → 120Ω Rdiff_min is the minimum transceiver differential input resistance → 20kΩ Nmax is the maximum number of node on the bus → let’s say 30 Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  10. CAN bus signal The result for NE06 cable & 30 nodes is : 111m! Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  11. Standard configuration ATLAS DCS Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  12. Cable characteristic impedance • The ISO 11898 CAN standard prescribes that the cable impedance be nominally 120Ω. But an impedance interval of 108 to 132Ω is permitted. Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  13. Cables datasheets • NG18 (SCEM : 04.21.52.218.9) • NE06 (SCEM : 04.21.52.110.0) Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  14. Cable propagation delay • Signal velocity in cable : Lossless lumped equivalent circuit Example : 2x0.5mm2 NE P cable L : 0.65µH/m C : 0.075nF/m V = 0.143m/ns Thus tp = 698ns for 100m [m/s] [F/m] [H/m] Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  15. Signal reflection • Example with 100m of 90Ω cable and 250 Kbaud CAN speed The bit duration is : 4µs The reflection duration : 1.4µs In this case (120Ω termination) : 1st reflection level : V1 = Vs*Ctl = Vs*1.143 (+14%) 2nd reflection level : V2 = Vs*Ctl*[1+Crl*Crs] = Vs*0.98 (-2%) 3rd reflection level : V3 = Vs*Ctl*[1+Crl*Crs+(Crl*Crs)2] = Vs*1.003 Ctl : load transmission coefficient Crl : load reflection coefficient Crs : source reflection coefficient Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  16. Signal reflection SUMMARY 0.47V margin 0.32V margin Signal wave form & noise margin Bounce diagram Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  17. Solutions proposed ATLAS DCS • The thick cable and connectors associated Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  18. Solutions proposed ATLAS DCS • The junction box Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  19. Solutions proposed ATLAS DCS • The thin cable and connectors associated Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  20. Solutions proposed ATLAS DCS • The prices for the thin cable : • The 3 twisted pairs cable: 1.60 CHF/m • Two single connectors (a male and a female): 18.31 CHF • One double connector : 34.61 € Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  21. Monitoring board CAN supply • Supply topology ELMB digital supply D-SUB 9 pins ELMB ADC supply HAVE TO BE REPLACED BY LOWER VALUE RESISTORS Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  22. Monitoring board TOTAL VAP+VDP = 59mA without Air flow 84mA with Air flow @ Ta=45°C Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  23. The simulation tool ATLAS DCS • The front panel Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  24. The simulation tool ATLAS DCS • Tests of the software Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  25. Some examples… ATLAS DCS Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  26. Conclusion ATLAS DCS • This design of the wiring will work without problem for our CAN bus applications. • Wiring of the first rack monitoring boards will begin next Monday (16/05) => Test in real conditions Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

  27. AND NOW • MAKE A REALISTIC TEST (Planed week 19) With 30 monitoring card & around 100m of thick cable. Sébastien Franz PH-ATI-DC Stéphane Detraz PH-ESS

More Related