1 / 36

Online Monitoring of Power Control and Engineering Parameters in the NEMO Phase-2 Tower

This international workshop discusses the power control and engineering parameter systems of the NEMO Phase-2 tower, including electrical parameter display, monitoring of voltage and current, power feeding switches control, and protection against overcurrent and overvoltage.

myrae
Download Presentation

Online Monitoring of Power Control and Engineering Parameters in the NEMO Phase-2 Tower

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. International Workshop on a Very Large Volume Neutrino Telescope for the Mediterranean Sea On line monitoring of the power control and engineering parameters systems of the NEMO Phase-2 tower Angelo Orlando INFN-LNS 22-24 April 2008, Toulon Palais Neptune Conference Centre

  2. System Overview • Power control system • Electrical parameter display of the 10KVdc – 400Vdc Alcatel MVC • Floors and base tower voltage and current monitoring • Power feeding switches control and check • Overcurrent and overvoltage protection • Tower engineering parameters • Depth of each floor (pressure sensors) • Roll, pitch and heading angle (accelerometer and magnetometer sensors fusion) • Accelerometers and magnetometers sensors raw data

  3. Outline • Subsystems: • Powercontrolsystem • Datatransmission • Control and power supply • Tower engineering parameters • Roll, pitch and heading • Tri-axial accelerometers raw data • Floors depth

  4. RS485 Copper Ethernet-Copper Ethernet-Fiber Ethernet Copper Data transmissionarchitecture • System Overview • On Shore • - Ethernet – Copper from PC • - Copper-Fiber media converter • Off Shore • - Copper-Fiber media converter • - E2S Eth to RS485 Half Duplex

  5. Data transmissionperformance • Test procedure • Oscilloscope probe at tower base • Master PC data request • Answer received from slave board Slave Answer #0 - - - - - - - #16 Master request 1200m Twistedpair (1 ms/div)

  6. Outline • Subsystems: • Powercontrolsystem • Datatransmission • Control and power supply • Tower engineering parameters • Roll, pitch and heading • Tri-axial accelerometers raw data • Floors depth

  7. Architecture overview • 10KVdc 1A PFE • Provided with: • all necessary safety requirements • a dummy load for operational testing NEMO Tower MVC - Alcatel DC/DC 10KVdc to 400Vdc Power Feed Equipment PFE 10KVdc NEMO Tower Base Cable • Power feeding and control system • Tower base electronic boards • Power supply and data bus along the backbone • Floor Power Control System (FPCS) • Floor Power Module System (FPMS)

  8. Architecture overview • AOLC4 • The OALC4 cable can be used at any • sea depth between 0 and 7000 meters (1.0 ohm/km version) NEMO Tower MVC - Alcatel DC/DC 10KVdc to 400Vdc Power Feed Equipment PFE 10KVdc NEMO Tower Base Cable • Power feeding and control system • Tower base electronic boards • Power supply and data bus along the backbone • Floor Power Control System (FPCS) • Floor Power Module System (FPMS)

  9. Architecture overview • MVC – Alcatel • Input: up to 10 kV DC • Output: 400 VDC/25 A • Estimated efficiency: > 90% at full load NEMO Tower MVC - Alcatel DC/DC 10KVdc to 400Vdc Power Feed Equipment PFE 10KVdc NEMO Tower Base Cable • Power feeding and control system • Tower base electronic boards • Power supply and data bus along the backbone • Floor Power Control System (FPCS) • Floor Power Module System (FPMS)

  10. Architecture overview NEMO Tower • NEMO TOWER MVC - Alcatel DC/DC 10KVdc to 400Vdc Power Feed Equipment PFE 10KVdc NEMO Tower Base Cable • Power feeding and control system • Tower base electronic boards • Power supply and data bus along the backbone • Floor Power Control System (FPCS) • Floor Power Module System (FPMS)

  11. Main Control System FPCS SPI & 5.5 VDC 12V Power Module FPMS 5.5V 4.2V Redundant Control system FPCS • Floor wiring • TOWER BASE • ARCHITECTURE SPI & 5.5VDC Twisted Pair B-RS485 Normal Twisted Pair A-RS485 Redundancy Twisted Pair C-400VDC OddFloor Twisted Pair D-400VDC EvenFloor Tower Base PCS + FPMS

  12. Base tower power control system Floor 16 Voltage sensors Temp Fiber From Frame Microcontroller A/D RS485 … IRQ Ethernet2SPI Media Converter Twisted Pair Cmd CK Floor 1 Power supply for Control system DC/DC 400V-5V RS485 400Vdc From DC/DC Current 400Vdc

  13. Base tower power control system • Power supply for power control system Floor 16 Voltage sensors Temp Fiber From Frame Microcontroller A/D RS485 … IRQ Ethernet2SPI Media Converter Twisted Pair Cmd CK Floor 1 Power supply for Control system DC/DC 400V-5V RS485 400Vdc From DC/DC Current 400Vdc

  14. Base tower power control system • Voltage and current sensors Floor 16 Voltage sensors Temp Fiber From Frame Microcontroller A/D RS485 … IRQ Ethernet2SPI Media Converter Twisted Pair Cmd CK Floor 1 Power supply for Control system DC/DC 400V-5V RS485 400Vdc From DC/DC Current 400Vdc

  15. Base tower power control system • Data transmission: Fiber/Ethernet TO Copper/RS485 Floor 16 Voltage sensors Temp Fiber From Frame Microcontroller A/D RS485 … IRQ Ethernet2SPI Media Converter Twisted Pair Cmd CK Floor 1 Power supply for Control system DC/DC 400V-5V RS485 400Vdc From DC/DC Current 400Vdc

  16. Main Control system FPCS SPI & 5.5 VDC 12V Power Module FPMS 5.5V 4.2V Redundant Control system FPCS • Floor wiring • FLOOR POWER • SUPPLY SPI & 5.5VDC Twisted Pair B-RS485 Normal Twisted Pair A-RS485 Redundancy Twisted Pair C-400VDC OddFloor Twisted Pair D-400VDC EvenFloor Tower Base PCS + FPMS

  17. I I I V V V V • FPMS - Floor Power Module System 100mm DC-DC Converter +12V ON-OFF RTN +400V +5.5V +5.5V DC-DC Converter Input Circuit protection Output filter Input filter +4.2V Dissipative Regulator ON-OFF Redundant switch ON-OFF Main switch 160mm ON-OFF +5.5V Control Circuit Connector GND DC-DC Status Maincontrol Redundantcontrol I/O I/O SPI SPI • Main specifications • Soft Start and over voltage protection • Input output filter noise reduction • Output current and voltage sensors • Optocoupled insulated high voltage sensor • n°2 switches for power on and off, main and redundant

  18. I I I V V V V • FPMS - Floor Power Module System 100mm DC-DC Converter +12V ON-OFF RTN +400V +5.5V +5.5V DC-DC Converter Input Circuit protection Output filter Input filter +4.2V Dissipative Regulator ON-OFF Redundant switch ON-OFF Main switch 160mm ON-OFF +5.5V Control Circuit Connector GND DC-DC Status Maincontrol Redundantcontrol I/O I/O SPI SPI • Main specifications • Soft Start and over voltage protection • Input output filter noise reduction • Output current and voltage sensors • Optocoupled insulated high voltage sensor • n°2 switches for power on and off, main and redundant

  19. I I I V V V V • FPMS - Floor Power Module System 100mm DC-DC Converter +12V ON-OFF RTN +400V +5.5V +5.5V DC-DC Converter Input Circuit protection Output filter Input filter +4.2V Dissipative Regulator ON-OFF Redundant switch ON-OFF Main switch 160mm ON-OFF +5.5V Control Circuit Connector GND DC-DC Status Maincontrol Redundantcontrol I/O I/O SPI SPI • Main specifications • Soft Start and over voltage protection • Input output filter noise reduction • Output current and voltage sensors • Optocoupled insulated high voltage sensor • n°2 switches for power on and off, main and redundant

  20. I I I V V V V • FPMS - Floor Power Module System 100mm DC-DC Converter +12V ON-OFF RTN +400V +5.5V +5.5V DC-DC Converter Input Circuit protection Output filter Input filter +4.2V Dissipative Regulator ON-OFF Redundant switch ON-OFF Main switch 160mm ON-OFF +5.5V Control Circuit Connector GND DC-DC Status Maincontrol Redundantcontrol I/O I/O SPI SPI • Main specifications • Soft Start and over voltage protection • Input output filter noise reduction • Output current and voltage sensors • Optocoupled insulated high voltage sensor • n°2 switches for power on and off, main and redundant

  21. I I I V V V V • FPMS - Floor Power Module System 100mm DC-DC Converter +12V ON-OFF RTN +400V +5.5V +5.5V DC-DC Converter Input Circuit protection Output filter Input filter +4.2V Dissipative Regulator ON-OFF Redundant switch ON-OFF Main switch 160mm ON-OFF +5.5V Control Circuit Connector GND DC-DC Status Maincontrol Redundantcontrol I/O I/O SPI SPI • Main specifications • Soft Start and over voltage protection • Input output filter noise reduction • Output current and voltage sensors • Optocoupled insulated high voltage sensor • n°2 switches for power on and off, main and redundant

  22. I I I V V V V • FPMS - Floor Power Module System 100mm DC-DC Converter +12V ON-OFF RTN +400V +5.5V +5.5V DC-DC Converter Input Circuit protection Output filter Input filter +4.2V Dissipative Regulator ON-OFF Redundant switch ON-OFF Main switch 160mm ON-OFF +5.5V Control Circuit Connector GND DC-DC Status Maincontrol Redundantcontrol I/O I/O SPI SPI • Main specifications • Soft Start and over voltage protection • Input output filter noise reduction • Output current and voltage sensors • Optocoupled insulated high voltage sensor • n°2 switches for power on and off, main and redundant

  23. Main Control system FPCS SPI & 5.5 VDC 12V Power Module FPMS 5.5V 4.2V Redundant Control system FPCS • Floor wiring • POWER CONTROL SYSTEM BOARD SPI & 5.5VDC Twisted Pair B-RS485 Normal Twisted Pair A-RS485 Redundancy Twisted Pair C-400VDC OddFloor Twisted Pair D-400VDC EvenFloor Tower Base PCS + FPMS

  24. PCS - Power Control System 130mm 55mm Backbone Ax Tx • Main features: • Power consumption: 150 mA @ 5.5Vdc • RS485 optocoupled interface • FPMS SPI interface • Over current and voltage protection • n°1 tri-axial magnetometer • n°3 MEMS accelerometers • n°2 Temp. and pressure interfaces μC PIC18F4523 Optocoupled RS485Driver Rx Ay En Az Temperature Connector (DS18S20) Pres Micromag3 SPI Bus SPI for FPMS - Connector

  25. PCS - Power Control System 130mm 55mm Backbone Ax Tx • Main features: • Power consumption: 150 mA @ 5.5Vdc • RS485 optocoupled interface • FPMS SPI interface • Over current and voltage protection • n°1 tri-axial magnetometer • n°3 MEMS accelerometers • n°2 Temp. and pressure interfaces μC PIC18F4523 Optocoupled RS485Driver Rx Ay En Az Temperature Connector (DS18S20) Pres Micromag3 SPI Bus SPI for FPMS - Connector

  26. PCS - Power Control System 130mm 55mm Backbone Ax Tx • Main features: • Power consumption: 150 mA @ 5.5Vdc • RS485 optocoupled interface • FPMS SPI interface • Over current and voltage protection • n°1 tri-axial magnetometer • n°3 MEMS accelerometers • n°2 Temp. and pressure interfaces μC PIC18F4523 Optocoupled RS485Driver Rx Ay En Az Temperature Connector (DS18S20) Pres Micromag3 SPI Bus SPI for FPMS - Connector

  27. PCS - Power Control System 130mm 55mm Backbone Ax Tx • Main features: • Power consumption: 150 mA @ 5.5Vdc • RS485 optocoupled interface • FPMS SPI interface • Over current and voltage protection • n°1 tri-axial magnetometer • n°3 MEMS accelerometers • n°2 Temp. and pressure interfaces μC PIC18F4523 Optocoupled RS485Driver Rx Ay En Az Temperature Connector (DS18S20) Pres Micromag3 SPI Bus SPI for FPMS - Connector

  28. PCS - Power Control System 130mm 55mm Backbone Ax Tx • Main features: • Power consumption: 150 mA @ 5.5Vdc • RS485 optocoupled interface • FPMS SPI interface • Over current and voltage protection • n°1 tri-axial magnetometer • n°3 MEMS accelerometers • n°2 Temp. and pressure interfaces μC PIC18F4523 Optocoupled RS485Driver Rx Ay En Az Temperature Connector (DS18S20) Pres Micromag3 SPI Bus SPI for FPMS - Connector

  29. PCS - Power Control System 130mm 55mm Backbone Ax Tx • Main features: • Power consumption: 150 mA @ 5.5Vdc • RS485 optocoupled interface • FPMS SPI interface • Over current and voltage protection • n°1 tri-axial magnetometer • n°3 MEMS accelerometers • n°2 Temp. and pressure interfaces μC PIC18F4523 Optocoupled RS485Driver Rx Ay En Az Temperature Connector (DS18S20) Pres Micromag3 SPI Bus SPI for FPMS - Connector

  30. PCS - Power Control System 130mm 55mm Backbone Ax Tx • Main features: • Power consumption: 150 mA @ 5.5Vdc • RS485 optocoupled interface • FPMS SPI interface • Over current and voltage protection • n°1 tri-axial magnetometer • n°3 MEMS accelerometers • n°2 Temp. and pressure interfaces μC PIC18F4523 Optocoupled RS485Driver Rx Ay En Az Temperature Connector (DS18S20) Pres Micromag3 SPI Bus SPI for FPMS - Connector

  31. PCS - Power Control System 130mm 55mm Backbone Backbone Ax Tx • Main features: • Power consumption: 150 mA @ 5.5Vdc • RS485 optocoupled interface • FPMS SPI interface • Over current and voltage protection • n°1 tri-axial magnetometer • n°3 MEMS accelerometers • n°2 Temp. and pressure interfaces μC PIC18F4523 Optocoupled RS485Driver Rx Ay En Az Temperature Connector (DS18S20) Pres Micromag3 SPI Bus SPI for FPMS - Connector

  32. Outline • Subsystems: • Powercontrolsystem • Datatransmission • Control and power supply • Tower engineering parameters • Roll, pitch and heading • Tri-axial accelerometers raw data • Floors depth

  33. Attitude System – Sensor Fusion Algorithm • Implemented algorithm • Roll and pitch angles can be calculated in almost static condition through accelerometers measures. • Roll and pitch angles are used to project the tri-axial magnetic measurements on the level plane surface. • Applying the rotational equations the heading angle is computed. x y z Yaw Roll Pitch

  34. Test: Roll – Pitch comparison and validation • Test results: PCS Vs MTi • Dynamic condition: • Error Roll ≤ 2° • Error Pitch ≤ 1.5° • Static condition: • Error Roll ≤ 0.2° • Error Pitch ≤ 0.1° MTi by XSens PCS by INFN-LNS

  35. Performed tests • Data transmission • Fiber copper converter (100Km fiber length) → OK • Bus RS485 tested (1200m backbonelength) → OK • Control system and power supply • Power Control System Board → OK • Floor Power Module System Board → OK • PCS - FPMS Integration → OK • Current and voltage measures validation → OK • Over current monitor → OK • Overcurrent protection → OK • Full system under pressure working @350Atm → OK • Tower engineering parameters • Roll, pitch and heading validation → OK • Pressure sensor validation @350Atm → OK • MEMS accelerometers under pressure working@350Atm → OK

  36. CONCLUSIONS ALL THE ELEMENTS OF THE NEMO PHASE 2 POWER AND POWER CONTROL SYSTEMS SUCCESFULLY TESTED THE SYSTEM IS READY FOR THE INTEGRATION

More Related