1 / 11

RSH Front End Electronic

RSH Front End Electronic. R. Beaujean, S. Böttcher. Kiel Nov 07, 2005. CSA. Detector FET + OpAmp shaping amp. Feed back. Front End Electronic Block Diagramm. Feed back network: C f and R f (parallel)

natala
Download Presentation

RSH Front End Electronic

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. RSH Front End Electronic R. Beaujean, S. Böttcher Kiel Nov 07, 2005

  2. CSA Detector FET + OpAmp shaping amp Feed back Front End Electronic Block Diagramm Feed back network: Cf and Rf (parallel) Cf (pF) defines sensitivity : (44/Cf ) mV/MeV (for Si) Rf (MegOhm) defines time constant of discharging (pile up) shaping amplifier: signal level conditioning for ASIC input improves signal to noise ratio can select fast charge collection

  3. CSA Noise considerations: increasing with: detector capacitance (e.g. 85 pF @ 300 um, 2 cm²) detector dark current ~ SQRT(Id) (doubles every 8 degree K) decreasing with: increasing FET current noise ~ 1/SQRT(gm); gm~SQRT(Id) gm (mutual conductance, forward transfer admittance) is the parameter we can influence by selecting the type of FET and the FET drain current (--> power consumption).

  4. CSA noise versus input capacitance (typical FET)

  5. Range of Energy Deposit Measurements in Si The minimum detectable energy deposit must be ~ 60 keV (well below 115 keV of MIPs in 300 um Si) assuming a dynamic range of 10k for the analogue section, this gives an upper limit of 600 MeV energy deposit Maximum output voltage of the CSA is ~3 Volt --> Cf = 44 mV * 600 MeV / 3V = 8.8 pF the CSA output for 60 keV energy deposit is then 0.3 mV

  6. How to improve the resolution for required energy deposit range at given ADC resolution For CsI and BC430M: Photodiode1+ CSA1 with low Cf for lowE events (high gain) Photodiode2+ CSA2 with med. Cf for med.E events (med. gain) Photodiode3+ CSA3 with high Cf for highE events (low gain) For SSD (A, B, C detectors) : only 1 block of SSD-detector + CSA behind the CSA two independent shaping amplifiers with low (x1) and high (x16) gain respectively (the CSA defines the dynamic range).

  7. Layout of typical CSA (Kiel) for PIN2774

  8. Kiel-CSA + 2 cm² detector: rms noise ~ 3 keV

  9. Components small size, SMD active components required 1. FET: BF862 SOT23-3 plastic package equivalent noise input voltage 0.8 nV/Hz input capacitance 10 pF transfer admittance gm 45 mS typ. 2. OpAmp: AD8005 SOT23-6 plastic package low quiescent current ~ 400 uA low noise, high slew rate, plastic packages have to be qualified for flight

  10. Quiescent Power consumption CSA: FET drain Id~ 4mA @ 3V; amplifier 0.5 mA@ +-5V noise critical FETs may be operated with Id>4 mA, less critical FETs may be operated with Id<4 mA shaping amplifier: 0.5 mA@ +-5V Interface to ASIC positive output signal, shaping time TBD (1-5 us)

More Related