Cross section measurements for analysis of D and T in thicker films

1. Cross section measurements for analysis of D and T in thicker films Liqun Shi Institute of Modern Physics, Fudan University, Shanghai, 200433, People’s Republic of China

2. 一、Scientific Background 二、Experimental technique • The targets • Experimental system • The measurement of recoil cross section 三、Experimental Results

3. Accurate knowledge of the concentration of hydrogen and its isotopes in materials is important in a wide range of application. The elastic recoil detection analysis(ERDA) and Proton backscattering (PBS) are important analytical methods for their concentration determination. For samples containing multiple hydrogen isotopes with several µm’s thickness, it may be necessary to perform high energy ERDA in order to achieve good 一、Scientific Background

4. mass resolution and to analysis relative thick sample. But for the sample with much thicker samples or the bulk materials, it may also become necessary to employ proton backscattering technique to achieve large depth detection and relative good sensitivity for D,T. In either case, accurate knowledge of the elastic scattering cross-sections for the incident beam interaction with the hydrogen isotopes or materials of interest is required. • In previous works, some cross-sections for the interaction

5. of 4He2+ beams with hydrogen isotopes (1-3.05 and 9-11 MeV for2H(,)2H, and 0.5-2.5 and 9-11 MeV for 3H(,)3H), and for the interaction of proton with D and T at some energy range (2-2.78MeV for 2H(p,p)2H at 151o and 2.74-3.49 MeV for 3H(p,p)3H at 163.2 o ), have been measured although there are some unresolved discrepancies for different data sources. However, very little data exist for proton incident on D,T in the energy range 1-3 MeV and

6. at assured angles, and No data for He ions on D,T in the energy range 3-8MeV in the literature are found. • In order to make high accurate He- ERD analysis of D and T in the films with a thickness of less than 4 um under the condition of confined energy of accelerator, as well as the measurement of D and T concentration and depth profiles

7. in the thick films or bulk materials by PBS technology， in this project we will perform the measurement of the cross-sections in energy range of interest: (1) Helium on D and T in the energy range 3 –7.6 MeV at a recoil angle of 30o. (2) Proton incident on D and T in the energy range 1-3 MeV at 165o , respectively .

8. 二、Experimental technique 2.1 The targets • TiTx (TiDx) targets are prepared by thermal sorption of tritium or deuterium on Ti films. • In order to measure the cross section for ERD, the Ti films of 2.81017/cm2(50nm) with an overlayer Pd of 2nm(Pd/TiDx)are deposited on the quartz substrates. Here Pd was used to improve absorption activity of Ti and obtain a high concentration of D in the Ti. It is found in previous experiment that T or D was located entirely in the Ti film and that virtually no T or D migrated into the quartz.

9. For the measurement of PBS cross section, a multilayer compound filmPd/TiD(T)x (100 nm) /Al was employed. Here the Al foil(7um) was used to support Ti film but maintain a very low background . Pd overlayer is not only used to serve as an internal ion dose reference, and also to act as a protection against oxygenization. • The chosen film thickness is a compromise between minimizing the energy lose in traversing the film and having a definite amount of D or T.

10. 2.2 Experimental system • A NEC 9SDH-2 3 MV tandem accelerator are used in this experiment, which can provide well collimated beam of He and H. The beam is incident on the target through a defining aperture of 0.6 mm. • Two Au/Si surface barrier detectors are used to allow simultaneous collection of ERD and RBS spectra, thus avoiding the need to depend on the absolute charge collection. ERD detector is fixed at the recoil angle of 300. The aperture in front of the detector had dimension 23

11. 5MeVO3+ Mylar Foil E Detector Schematic of experimental system for ERD and RBS measurement

12. mm, which results in an angular resolution of 1.40. The RBSdetectoris placed at 1650 and it subtended a solid angle of 1.25 msr • For measurement of PBS cross section, the Au/Si detectoris placed at 1510 and 1650 , respectively. • The accelerator energy is calibrated by using both nuclear resonance reactions of 27Al(p,)28Si at 992 keV, 19F(p,)28O at 872 keV and 241Am source.

13. 2.3 The measurement of recoil cross section • Cross-sections for the 2H(,)2H and 3H(,)3H ERD interactions can be determined by (1) absolute accuracy of for c.m.s energies < 500 keV. T(d, )n reaction with a quoted accuracy of 2% where A(E) is the integrated area under the peak,1 the angle of the target normal relative to the incident beam(up-stream), N the area density of the recoil product,  the solid angle subtended by the detector and Q is the total number of He ions incident on the target.

14. For the hydride film used in experiment, besides A(E) (possible multiple scattering effect), hydrogen isotope concentration N is also a difficult parameter accurately to be determined in order to achieve ideal precision. • in above equation can be obtained by simultaneous solving ERD and RBS spectra of He ions as well as 5 MeV O3+ imping on the sample.

15. RBS (a) and ERD(b)Spectra for 3.4 MeV He ions incident at 150 to the surface of the Pd/TiD/SiO2 films

16. Thus, (2) where E = E0 - EPd, E0 is the incident He(or O) ion energy,  EPd is theenergy loss of ion in the Pd film. In this way, the accuracy of the recoil cross sections measured here is only limited by the following uncertainties: A(E), the statistical uncertainty, is typically 3%; and .Because thickness of target is very thin(15 nm), main error for is

17. The total error associated with the cross sections measured is not larger than 7% 2.4 The measurement of proton elastic scattering cross sections • By using Pd/TiD(T)x compound film, the elastic scattering cross-sections of D or T can be calculated from: (3)

18. where is the calculate proton Rutherford scattering cross section of Pd. The ratio (N=atom density, t=layer thickness) is determined using the areal density value for from ERD measurements(5%). and measuring by proton backscattering. The signal peak area ratios is determined from the measured spectra. • The total estimated errors for the cross sections measured is less than 8%

19. The PBS spectrum of Pd/TiD/Al hybrid film using 2.2MeV proton at 1650

20. 三、Experimental Results