1 / 34

Hand and Power Tools

Hand and Power Tools. 1 2 3 4 5 BONUS 6 7 8 9 10 BONUS 11 12 13 14 15 BONUS 16 17 18 19 20 BONUS 21 22 23 24 25 BONUS. What type of hammer should never be used in the construction industry? Sledge Hammer Ball Peen Hammer Cast Head Hammer Claw Hammer. A B C D.

nelia
Download Presentation

Hand and Power Tools

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Hand and Power Tools 12345BONUS 678910BONUS 1112131415BONUS 1617181920BONUS 2122232425BONUS

  2. What type of hammer should never be used in the construction industry? Sledge Hammer Ball Peen Hammer Cast Head Hammer Claw Hammer ABCD

  3. When it is important that the object you are striking not be damaged which tool is the best one to use? Bell faced Hammer Claw Hammer Sledge Hammer Mallet ABCD

  4. Which of the following should you wear when you use a nail puller or a ripping bar? Safety Glasses, Hard Hat, Ear Plugs Hard Hat, Safety Glasses, Gloves Safety Glasses, gloves, Resporator Hard Hat, Ear Plugs, Gloves ABCD

  5. Safe use of a wrench requires you to do which of the following? Push it away from you. Pull it towards you. Use an extension. Use the shortest handle available. ABCD

  6. Which of the following wrenches is adjustable? Striking Wrench Box-end Wrench Pipe Wrench Combination Wrench ABCD

  7. Which tool would you use to drive a stake into the ground 18” to 24”? Claw Hammer Sledge Hammer Wooden Mallet Slag Hammer ABCD

  8. A crosshead screw is tightened by using which of the following? Allen Wrench Torx Screwdriver Phillips Head Screwdriver Robertson Head Screwdriver ABCD

  9. Which of the following would you use to cut heavy gauge wire? Lineman's Pliers Needle-nose Pliers Channellock Pliers Slip-joint Pliers ABCD

  10. You should discard a clamp with a ________. Ridged Jaw Sliding Jaw Swivel Jaw that turns freely Bent Frame ABCD

  11. Which of the following is used to measure vertical distances? Steel Rule Micrometer Measuring Tape Wooden Folding Rule ABCD

  12. Which one of these should be sharpened on an oil stone? Punch Chisel File Screwdriver ABCD

  13. A _______ Square is used to mark many different angles. Try Carpenter’s Rafter Angle Framing ABCD

  14. Proper maintenance of pliers and wrenches requires you to do which of the following? Wipe with a soft cloth Use Grease Oil the joints Wash with Water ABCD

  15. When is a surface plumb? Centered between two objects Exactly horizontal Exactly vertical At a 45 degree angle ABCD

  16. Use this to maintain a saw blade properly. Sand paper Grinder Emery cloth A file ABCD

  17. Which of the following bits are used to drill in wood? Auger Carbide Shank Masonry ABCD

  18. A saber saw will cut more smoothly if you use this. Oil Water Grease Beeswax ABCD

  19. ALWAYS do this when working on any power tool. Disconnect power Set the trigger lock Remove the blade Apply grease ABCD

  20. You should stand at this point when using a circular saw. Directly behind the work To one side of the work Directly in front of the cut Directly over the work. ABCD

  21. Air pressure is used to power this kind of tool. Hydraulic Pneumatic Aerodynamic Electromagnetic ABCD

  22. This is essential to the safe operation of an electric drill. Keyless chuck Trigger lock GFCI outlet Chuck key holder ABCD

  23. When cutting with a circular saw you should always cut on this side of the line. Top Bottom Finish side Waste or unused side ABCD

  24. To extend the life of a hand held band saw blade you should do which of the following? Operate at low speed Operate at high speed Vary the speed Operate at medium speed ABCD

  25. What do you do if a nail gun leaves the nail head above the surface. Lower the air pressure Raise the air pressure Lower the nail size Raise the nail size ABCD

  26. The first step for operating an electromagnetic drill is_____. Put the power to the On position Put the electromagnetic switch to the On position Set the depth gauge Turn the switch OFF ABCD

  27. Which of these grinders is used to smooth a damaged chisel head? End Angle Bench Detail ABCD

  28. BONUS A cracked grinder wheel will do which of the following? Ring clearly Make a dull thud Splinter Develop visible cracks. ABCD

  29. BONUS When does a belt sander work best? When it is stationary on the surface to be sanded Started at low speed When used with high grit paper Running at full speed before you touch the surface ABCD

  30. BONUS Dust from an electric sander is _______. Harmless Explosive Will damage the sander Completely removed from the collection system ABCD

  31. BONUS Which of the following is used to break brick or concrete? pavement breaker Hammer drill Pneumatic drill Hydraulic jack ABCD

  32. BONUS How far away should you keep any part of your body from a cutting tool? 1’ 6’ 3” 6” ABCD

  33. INCORRECT

  34. CORRECT

More Related