190 likes | 281 Views
Min-E-Con. Your Total Microminiature Connection. Miniaturization Trends.
E N D
Min-E-Con Your Total Microminiature Connection
Miniaturization Trends The trend towards miniaturization of electronics equipment which began more than three decades ago has grown dramatically in the 21st century. During much of this time Min-E-Con has been among the leaders in the design and manufacture of high-density Microminiature and Nanominiature connection devices. The proven reliability of our "Fifty-Lok" contact design and it's inherent low insertion forces have made it the preferred choice of many users. Min-E-Con connectors are ideal for applications that require: • High contact densities • High temperatures (200C+) • Extreme shock and vibration • Mission Critical / High Reliability • Reduced weight and size • High speed data transmission
About Min-E-Con • Founded in 1974 • Privately Owned • Products built in Irvine California, USA • Focused exclusively on Micro and Nano connectors • 80% of business is Oil / Down Hole tools • 15+ million per year in sales • Holden Technologies, Inc. Rep for 10+ years • Trendsetter Electronics – Sole Distributor for 8+ years
Min-E-Con Products Micro Connectors Nano Connectors Strip Connectors Custom Connectors and Harnesses
Micro – D Connectors Mil-83513 24AWG or smaller wire. 22AWG special 3A, 600V rating. 2000 mating cycles – LIF contacts Low Profile with chamfered edges (DNBR) Low Profile (DSMR), Original D, Small D. available
Nano Connectors Nano are approximately 20% the size of a micro 1Amp, 250V rating NMR1 – drop in replacement for Tyco/Nanonics (.025 centers) NMR2 – modern nano for new designs (.030 centers) PEEK Flex – custom, quick turn Nano’s
Strip Connectors Modular Low Cost Stackable Guide Pin can be positioned to avoid mis-mating Jackscrew now available
Harnesses Min-E-Con can provide complete custom harnesses Custom harnesses eliminate splices Fewer splices = higher reliability Min-E-Con can terminate a wide range of devices within a harness from torroids and filters to specialty connectors from other mfrs. Daisy Chaining Extended Backpotting Shield Termination
Specialty Products and Operations Hybrid Connectors: contain a mix of contact sizes. Nano, micro and 16 AWG contacts in a single micro-d. High voltage Non-Magnetic: Special plating and contacts that are without Ni. Extended Backpotting Double Crimp Shield termination
Min-E-Con Quality • Min-E-Con’s patented Fifty-Lok system mechanically locks the contacts into the harness. • Insulators are molded into the connector shell. Other mfrs glue their insulators. • Low insertion force system allows longer contact life. • 100% Testing: Every contact in every connector is tested to meet electrical specs. • Every contact on a harness is checked for proper routing. • Min-E-Con does not use “batch” testing like competitors. • Min-E-Con quality is highest in the industry.
New Product Development /06 – Super Seal
Additional Sealing – “Super Seal” Upgrade (/06) Many down hole tools are exposed to moisture and humidity in the field and during service. This moisture turns into a pressurized steam when exposed to high temperatures down hole. Steam destroys critical epoxy over time and can result in failures. To combat this type of failure, Min-e-con has added the option to place additional hydrophobic seals in between the epoxy and the insulator. This additional sealing prevents moisture and steam from penetrating to a point where shorting or electrical leakage can occur. - Connectors rated for 100% humidity at 15psi with high temp - Hydrophobic seal between insulator and epoxy - Prevents moisture wicking up wires - Prevents steam degradation of epoxy into the insulator area - Added sealing does not change the dimensions of the connector
Black Anodized Finish Black Anodized Finish Upgrade (”B” Callout) Hard Coat Anodization is not a plating but rather a transformation of the skin of the aluminum shell. Anodization provides numerous benefits : - Non Magnetic * - Corrosion Resistance - Hardness: Rockwell scale C60-70 - Wear Resistance - High Temp: 200C+ - Low Friction Coefficient for ease of mating - No plating to flake or chip
How to Specify Super Seal and Black Anodize Finish • MBR-15P6E5-18.0 /06 • “B” in second position denotes “BLACK ANODIZED” Finish • “/06” suffix denotes 200C rating and Additional Sealing
Non- Magnetic - /07 • Min-e-con has supplied non magnetic connectors to the oilfield for years. Typically, switching the finish to hard coat anodized and leaving the hardware off was sufficient for most requirements. However, with the increased sensitivity of today’s tools Min-e-con has gone the final step and removed even the Nickel underplate on the contacts. This product is now able to be easily ordered with the simple addition of the /07 part number suffix: • Hard Coat Black Anodized Finish • Nickel Free Contacts • Less Hardware
Thank You! Questions?