1 / 14

Unit 10 - Part 3

Unit 10 - Part 3. Address Selects Receiver. Receivers are put in “standby” mode by setting RWU (Receiver Wake Up) = 1. Address Character. N Character Message. XMTR. RCVR. RCVR. RCVR. RCVR. ……. Receiver Wake Up. If RWU == “1” (Receiver is in ‘stand-by’ state)

nitesh
Download Presentation

Unit 10 - Part 3

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. Unit 10 - Part 3

  2. Address Selects Receiver Receivers are put in “standby” mode by setting RWU (Receiver Wake Up) = 1 Address Character N Character Message XMTR RCVR RCVR RCVR RCVR ……..

  3. Receiver Wake Up • If RWU == “1” (Receiver is in ‘stand-by’ state) • If WAKE == “1” (Address Mark Wakeup) • A logic 1 in the msb position of a frame clears the RWU bit and wakes up the SCI. (The logic 1 marks the frame as an address frame.) • If Address matches, then Receive Message • If Address doesn’t match, then set RWU=“1” • If WAKE == “0” (Idle line Wakeup) • An idle condition on the input clears the RWU bit and wakes up the SCI. The next frame that is received is assume to contain an Address • If Address matches, then Receive Message • If Address doesn’t match, then set RWU=“1”

  4. RWU = “1”, WAKE = “0” Frame N+1 Characters Frame N+1 Characters Frame N+1 Characters Line Idle • Enable Receiver when receiver input is in Idle state (when 10 or 11 1’s are received) • Next received character is considered an Address • If Address matches then receive the rest of Frame • If Address doesn’t match, set RWU = ”1” to ignore rest of Frame

  5. RWU = “1” WAKE = “1” • Received “wakes up” if Most Significant Bit of Received Character = “1” • 1 in MSB: Character is an Address • Receive Address • If Match, receive remainder of frame • If No Match, set RWU back to “1” and ignore remainder of frame

  6. Single Wire Mode • Loops = “1”, RSRC = “1” • TxDIR = “0” -- TxData is Input to Receiver • TxDIR = “1” -- TxData is Transmitter Output XMTR TxDIR = “1” TxD pin Single Wire Half Duplex RCVR TxDIR = “0”

  7. SCI Interrupts • 4 Sources of Interrupts on SCI • TDRE = “1” – Transmitter SCI Buffer Empty • TC = “1” – Transmitter Finished • RDRF = “1” – Receiver SCI Buffer Full • IDLE = “1” – Receive Line is Idle • TDRE and RDRF are commonly used • TC and IDLE used in special applications

  8. SCI Interrupt Processing void sci0_isr(void) {// SCI Interrupt has occurred, determine reason if((SCI0SR1&0x20)!=0) { // RDRF=“1” was source of interrupt, buffer is full c=SCI0DRL; // Read character to empty buffer ---- // handle the character } if((SCI0SR1&0x80)!=0) { // TDRE=“1” was source of interrupt, buffer is empty // Case 1 – If have a character c to transmit SCI0DRL = c; // Write character to full buffer } else {// Case 2 – No character to transmit SCI0CR2 = SCI0CR2&0x7F; // set TIE=“0” to disable transmitter interrupts } ---- ---- }

More Related