1 / 24

A Charge Pump Based Receiver Circuit to Reduce Interconnect Power Dissipation

A Charge Pump Based Receiver Circuit to Reduce Interconnect Power Dissipation. Aatmesh Shrivastava, John Lach, and Benton H. Calhoun University of Virginia, Charlottesville. Interconnect Power Dissipation. [1] Magen , et. al. SLIP 2004.

odele
Download Presentation

A Charge Pump Based Receiver Circuit to Reduce Interconnect Power Dissipation

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript


  1. A Charge Pump Based Receiver Circuit to Reduce Interconnect Power Dissipation Aatmesh Shrivastava, John Lach, and Benton H. Calhoun University of Virginia, Charlottesville

  2. Interconnect Power Dissipation [1] Magen, et. al. SLIP 2004 • Interconnect consumes >50% of dynamic power in a micro-processor. • 90% of interconnect power is in 10% of interconnect.

  3. Interconnect Power in the context of next generation computing • A Exa-byte of data is to be transmitted per second to enable exascale computing. • [2] P. Kogge et. al. DARPA/ITPO 08 • State of the interconnect consumes 1-3pJ/bit/mm. A exabyte/s will need 10-30 Mega-Watt Power. [2]

  4. Outline • Voltage Scaling for Interconnect • Driver • Receiver • Literature Review • Proposed Interconnect Receiver • Charge Pump • Complete circuit diagram • Simulation • Implementing the interconnect in 4 core Alpha • Results • Design Comparison

  5. Voltage Scaling for interconnects • Voltage Scaling has been used to reduce interconnect power [4-10]. • Logic runs at rated VDD, wires at reduced VDDI. Interconnect driver circuits are needed • Key Question :- Performance overhead vs Power.

  6. Interconnect Driver [4] H. Zhang, et. al. TVLSI 2000 • Two NMOS transistors are used at output stage • A signal at logic level ( 1V) is converted to a signal interconnect level (0.3V) • We use this driver in our proposed interconnect circuit.

  7. Interconnect Receiver ON ON VDDI OFF 0 • Restores the signal back to the logic level. Poor performance, VDDI > VT. • Differential amplifier [8-10] can be used for better performance but have higher power overhead. • We propose an improved single ended receiver.

  8. Approx. Power-Performance-Area Prior Art • In prior art either energy saving is less or performance is poor.

  9. Delay vs Energy/bit : Prior Art • Existing solutions do not address power and performance in conjunction.

  10. Proposed receiver ckt • Charge-pump is used. • It boosts the signal to three times the interconnect swing • Good performance and much lower power

  11. Charge Pump in the Receiver • When IN is at 0, A is precharged to 0.3V. So when IN goes high A goes to 0.6V (Ideal case). • Similarly when IN is at 0.3V, A is precharged to 0V. So when IN goes low A goes to -0.3V (ideal). • Total swing at A is 0.9V. C swings from VT to VDD-VT

  12. Complete Circuit Diagram VTL 0V 1V 0V 0.3V VDD-VTL -0.3 VTL 1 1 0.3 VTL VTL+0.3 0 0.6 0 VTL 0 0.3 0 0

  13. Simulation results IN OUT • Reduced swing interconnect signal gets reconstructed with good performance.

  14. Delay vs Energy/bit • Proposed Solution gives very good performance and very low energy.

  15. Energy savings in a processor • Data-Bus of alpha was implemented using differential, basic and proposed interconnect circuit. • Over the set of splash benchmarks, the proposed interconnect saves up to 70% of energy.

  16. PPA : Power-Performance-Area • Novel interconnect circuit has best in class PPA

  17. Thank You

  18. References • NirMagen et. Al. “Interconnect-Power Dissipation in a Microprocessor” Workshop on System Level Interconnect Prediction 2004 • P. Kogge, K. Bergman, S Borka, et. al, “ExaScale Computing Study: Technology Challenges in Achieving Exascale Systems” DARPA/IPTO, September 2008 • E. Kusse and J.M. Rabaey, “Low-Energy Embedded FPGA Structures” IEEE International Symposium on Low Power Electronics Design, August 1998 . • H. Zhang, V. George and J.M. Rabaey, “Low-Swing On-Chip Signalling Techniques: Effectiveness and Robustness” IEEE Transactions on Very Large Scale Integration (VLSI), Vol-8 No-3, June 2000 • J.C.G. Montesdeoca, J.A. Montiel-Nelson and S. Nooshabadi, “CMOS Driver Receiver Pair for Low Swing Signalling for Low Energy On-chip Interconnects” IEEE Transactions on Very Large Scale Integration (VLSI), Vol-17 No-2, February 2009. • R. Ho, I. Ono, F. Liu, A. Chow, J. Schauar and R. Drost, “High Speed and Low Energy capacitively driven wires” IEEE International Solid State Circuits Conference, February 2007. • M. Ferretti and P.A. Beere “Low Swing Signaling Using a Dynamic Diode-Connected Driver” European Solid-State Circuits Conference, September 2001. • A. Narshimha, M. Kasotiya and R. Sridhar “A Low-Swing Differential signaling Scheme for on-chip Global Interconnects” International Conference on VLSI Design, January 2005. • N. Tzartzanis, W.W. Walker “Differential Current Mode Sensing for Efficient On-Chip global Signaling” IEEE Journal of Solid State Circuits, Vol-40 No-11, November 2005. • H. Ito, M. Kimura, K. Miyashita, T. Ishii, K. Okada and K. Masu, “A Bidirectional and Multidrop Transmission Line Interconnect for Multipoint to Multipoint On-Chip Communication” IEEE Journal of Solid State Circuits, Vol-43 No-4, April 2008. • V. Alder and E.G. Friedman, “Repeater Design to Reduce Delay and Power in Resistive Interconnects”. IEEE Transactions on Circuits and Systems-II, Vol-45 No-45, May 1998. • P.E. Allen and D.R. Holberg., “CMOS Analog circuit design” Oxford Press 2002. • R.E. Kessler, E.J. McLellan and D.A. Webb, “The Alpha 21264 Microprocessor Architecture” International Conference on Computer Design, October 1998. • N.L. Binkert, R.G. Dreslinski, L.R. Hsu, K.T. Lim, A.G. Saidi and S.K. Reinhardt, “The M5 Simulator: Modeling Networked Systems” IEEE Micro, July 2006.

  19. Back Up

  20. Complete Circuit Diagram • When IN goes hi, A goes to 0.6V, bringing B to ground. • OUT goes high completing the transition. • It also brings C to VDD-VT and precharges A to 0.6V

  21. Graph of A

  22. Initial Condition

  23. Static current

  24. Voltage Sensitivity

More Related