1 / 78

PCI 6 th Edition

PCI 6 th Edition. Lateral Component Design. Presentation Outline. Architectural Components Earthquake Loading Shear Wall Systems Distribution of lateral loads Load bearing shear wall analysis Rigid diaphragm analysis. Architectural Components.

oria
Download Presentation

PCI 6 th Edition

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. PCI 6th Edition Lateral Component Design

  2. Presentation Outline • Architectural Components • Earthquake Loading • Shear Wall Systems • Distribution of lateral loads • Load bearing shear wall analysis • Rigid diaphragm analysis

  3. Architectural Components • Must resist seismic forces and be attached to the SFRS • Exceptions • Seismic Design Category A • Seismic Design Category B with I=1.0 (other than parapets supported by bearing or shear walls).

  4. Seismic Design Force, Fp Where: ap = component amplification factorfrom Figure 3.10.10

  5. Seismic Design Force, Fp Where: Rp = component response modification factor from Figure 3.10.10

  6. Seismic Design Force, Fp Where: h = average roof height of structure SDS= Design, 5% damped, spectral response acceleration at short periods Wp = component weight z= height in structure at attachment point < h

  7. Cladding Seismic Load Example • Given: • A hospital building in Memphis, TN • Cladding panels are 7 ft tall by 28 ft long. A 6 ft high window is attached to the top of the panel, and an 8 ft high window is attached to the bottom. • Window weight = 10 psf • Site Class C

  8. Problem: Determine the seismic forces on the panel Assumptions Connections only resist load in direction assumed Vertical load resistance at bearing is 71/2” from exterior face of panel Lateral Load (x-direction) resistance is 41/2” from exterior face of the panel Element being consider is at top of building, z/h=1.0 Cladding Seismic Load Example

  9. Solution Steps Step 1 – Determine Component Factors Step 2 – Calculate Design Spectral Response Acceleration Step 3 – Calculate Seismic Force in terms of panel weight Step 4 – Check limits Step 5 – Calculate panel loading Step 6 – Determine connection forces Step 7 – Summarize connection forces

  10. Figure 3.10.10 Step 1 – Determine ap and Rp ap Rp

  11. Step 2 – Calculate the 5%-Damped Design Spectral Response Acceleration Where: SMS=FaSS Ss =1.5 From maps found in IBC 2003 Fa= 1.0 From figure 3.10.7

  12. Step 3 – Calculate Fp in Terms of Wp Wall Element: Body of Connections: Fasteners:

  13. Step 4 – Check Fp Limits Wall Element: Body of Connections: Fasteners:

  14. Step 5 – Panel Loading • Gravity Loading • Seismic Loading Parallel to Panel Face • Seismic or Wind Loading Perpendicular to Panel Face

  15. Step 5 – Panel Loading • Panel Weight • Area = 465.75 in2 • Wp=485(28)=13,580 lb • Seismic Design Force • Fp=0.48(13580)=6518 lb

  16. Step 5 – Panel Loading • Upper Window Weight • Height =6 ft • Wwindow=6(28)(10)=1680 lb • Seismic Design Force • Inward or Outward • Consider ½ of Window • Wp=3.0(10)=30 plf • Fp=0.48(30)=14.4 plf • 14.4(28)=403 lb • Wp=485(28)=13,580 lb • Seismic Design Force • Fp=0.48(13580)=6518 lb

  17. Step 5 – Panel Loading • Lower Window Weight • No weight on panel • Seismic Design Force • Inward or outward • Consider ½ of window • height=8 ft • Wp=4.0(10)=40 plf • Fp=0.48(30)=19.2 plf • 19.2(28)=538 lb

  18. Step 5 Loads to Connections

  19. Step 6Loads to Connections • Equivalent Load Eccentricity z=64,470/15,260=4.2 in • Dead Load to Connections • Vertical =15,260/2=7630 lb • Horizontal = 7630 (7.5-4.2)/32.5 =774.7/2=387 lb

  20. Step 6 – Loads to Connections

  21. Step 6 – Loads to Connections

  22. Step 6 – Loads to Connections • Center of equivalent seismic load from lower left • y=258,723/7459 y=34.7 in • z=41,973/7459 • z=5.6 in

  23. Step 6 – Seismic In-Out Loads • Equivalent Seismic Load • y=34.7 in • Fp=7459 lb • Moments about Rb • Rt=7459(34.7 -27.5)/32.5 • Rt=1652 lb • Force equilibrium • Rb=7459-1652 • Rb=5807 lb

  24. Step 6 – Wind Outward Loads

  25. Step 6 – Wind Outward Loads Fp • Center of equivalent wind load from lower left • y=267,540/6860 • y=39.0 in • Outward Wind Load • Fp=6,860 lb

  26. Step 6 – Wind Outward Loads • Moments about Rb • Rt=7459(39.0 -27.5)/32.5 • Rt=2427 lb • Force equilibrium • Rb=6860-2427 • Rb=4433 lb

  27. Step 6 – Wind Inward Loads • Outward Wind Reactions • Rt=2427 lb • Rb=4433 lb • Inward Wind Loads • Proportional to pressure • Rt=(11.3/12.9)2427 lb • Rt=2126 lb • Rb=(11.3/12.9)4433 lb • Rb=3883 lb

  28. Step 6 – Seismic Loads Normal to Surface • Load distribution (Based on Continuous Beam Model) • Center connections = .58 (Load) • End connections = 0.21 (Load)

  29. Step 6 – Seismic Loads Parallel to Face • Parallel load • =+ 7459 lb

  30. Step 6 – Seismic Loads Parallel to Face • Up-down load

  31. Step 6 – Seismic Loads Parallel to Face • In-out load

  32. Step 7 – Summary of Factored Loads • Load Factor of 1.2 Applied • Load Factor of 1.0 Applied • Load Factor of 1.6 Applied

  33. Distribution of Lateral Loads Shear Wall Systems • For Rigid diaphragms • Lateral Load Distributed based on total rigidity, r Where: r=1/D D=sum of flexural and shear deflections

  34. Distribution of Lateral Loads Shear Wall Systems • Neglect Flexural Stiffness Provided: • Rectangular walls • Consistent materials • Height to length ratio < 0.3 • Distribution based on • Cross-Sectional Area

  35. Distribution of Lateral Loads Shear Wall Systems • Neglect Shear Stiffness Provided: • Rectangular walls • Consistent materials • Height to length ratio > 3.0 • Distribution based on • Moment of Inertia

  36. Distribution of Lateral Loads Shear Wall Systems • Symmetrical Shear Walls Where: Fi = Force Resisted by individual shear wall ki=rigidity of wall i Sr=sum of all wall rigidities Vx=total lateral load

  37. Distribution of Lateral Loads “Polar Moment of Stiffness Method” • Unsymmetrical Shear Walls Force in the y-direction is distributed to a given wall at a given level due to an applied force in the y-direction at that level

  38. Distribution of Lateral Loads “Polar Moment of Stiffness Method” • Unsymmetrical Shear Walls Where: Vy = lateral force at level being considered Kx,Ky = rigidity in x and y directions of wall SKx, SKy = summation of rigidities of all walls T = Torsional Moment x = wall x-distance from the center of stiffness y = wall y-distance from the center of stiffness

  39. Distribution of Lateral Loads “Polar Moment of Stiffness Method” • Unsymmetrical Shear Walls Force in the x-direction is distributed to a given wall at a given level due to an applied force in the y-direction at that level.

  40. Distribution of Lateral Loads “Polar Moment of Stiffness Method” • Unsymmetrical Shear Walls Where: Vy=lateral force at level being considered Kx,Ky=rigidity in x and y directions of wall SKx, SKy=summation of rigidities of all walls T=Torsional Moment x=wall x-distance from the center of stiffness y=wall y-distance from the center of stiffness

  41. Unsymmetrical Shear Wall Example Given: • Walls are 8 ft high and 8 in thick

  42. Unsymmetrical Shear Wall Example Problem: • Determine the shear in each wall due to the wind load, w • Assumptions: • Floors and roofs are rigid diaphragms • Walls D and E are not connected to Wall B • Solution Method: • Neglect flexural stiffness h/L < 0.3 • Distribute load in proportion to wall length

  43. Solution Steps Step 1 – Determine lateral diaphragm torsion Step 2 – Determine shear wall stiffness Step 3 – Determine wall forces

  44. Step 1 – Determine Lateral Diaphragm Torsion • Total Lateral Load Vx=0.20 x 200 = 40 kips

  45. Step 1 – Determine Lateral Diaphragm Torsion • Center of Rigidity from left

  46. Step 1 – Determine Lateral Diaphragm Torsion • Center of Rigidity y=center of building

  47. Step 1 – Determine Lateral Diaphragm Torsion • Center of Lateral Load from left xload=200/2=100 ft • Torsional Moment MT=40(130.9-100)=1236 kip-ft

  48. Step 2 – Determine Shear Wall Stiffness • Polar Moment of Stiffness

  49. Step 3 – Determine Wall Forces • Shear in North-South Walls

  50. Step 3 – Determine Wall Forces • Shear in North-South Walls

More Related