1 / 33

RIP v1 and RIP v2

RIP v1 and RIP v2. Routing Protocol. Router. Switch. Router. Router. Router. Router. Switch. What is an optimal route ?. Learning Objectives:. Comparing RIP v1 and v2 Enable RIPv2 on a router. Advertise networks using RIPv2. Configure Passive Interfaces.

paigee
Download Presentation

RIP v1 and RIP v2

An Image/Link below is provided (as is) to download presentation Download Policy: Content on the Website is provided to you AS IS for your information and personal use and may not be sold / licensed / shared on other websites without getting consent from its author. Content is provided to you AS IS for your information and personal use only. Download presentation by click this link. While downloading, if for some reason you are not able to download a presentation, the publisher may have deleted the file from their server. During download, if you can't get a presentation, the file might be deleted by the publisher.

E N D

Presentation Transcript

  1. RIP v1 and RIP v2

  2. Routing Protocol Router Switch Router Router Router Router Switch What is an optimal route ?

  3. Learning Objectives: • Comparing RIP v1 and v2 • Enable RIPv2 on a router. • Advertise networks using RIPv2. • Configure Passive Interfaces. • Summarizing Routes with RIPv2. • Disable RIPv2 automatically summarizes • Verify RIPv2 configuration. • Count to infinity problem • Authentication using rip v2 • Triggered route • Offset list

  4. RIP: Routing Information Protocol • The easiest Interior Gateway Protocol to configure • Distance vector routing protocol that broadcast entire routing table to neighbor every 30 seconds • RIP use hop count(the number of routers a packet must pass through to reach a particular network) as its sole metric • RIP has a maximum hop count of 15 • As a result RIP does not work in large network • RIP is capable of load balancing

  5. RIP: Routing Information Protocol • RIP’s administrative distance is 120 for both RIPv1 and RIPv2. • RIPv1 sends routing updates via multicast address 255.255.255.255 • RIPv2 sends routing updates via multicast address 224.0.0.9. • Cisco routers don’t enable RIPv2 by default. • RIP automatically summarizes routing updates. You can disable this by using the no auto-summary command.

  6. Distance VectorRouting Concepts

  7. RIP LAB

  8. Enabling RIP • Enabling RIP • Router(config)# router rip • Associates a network with RIP routing protocol • Router (config-router)# network ip-address • R1(config-router)#network 192.168.12.0 • Network 0.0.0.0 advertise all the network • Verifying • Router#showip route • Router#showiproute 1.1.1.0 • Router#showip protocols

  9. RIP v2 • Support plain text and MD5 authentication • Classless inter domain routing CIDR • Variable length subnet mask VLSM • Route summarization • Enabling RIP v2 • Router(config)#Router RIP • Router(config-router)#version 2

  10. Enabling RIP • Allowing unicast update for RIP: to control the set of interfaces with which you want to exchange routing information, you can disable the sending of routing updates by the command passive-interface • Router(config-router)#passive-interface loopback 0 • Define a neighbor router with which to exchange routing information • Router (config-router)#neighbor ip-address • RIP broadcast • Router(config-if)#ip ripv2-broadcast

  11. RIP timers • Router(config-router)# timers basic update invalid holddown flush • The rate at witch routing updates are sent(30 s) • The interval of time after witch a route is declared invalid(180 s) • The interval during witch we wait before we accept any new updates for the route that is in holddown (180 s) • The amount of time that must pass before a route is removed from the routing table(240 s) • Router(config-if)#ip rip advertise 30

  12. RIP timers Turnethe RIP timers so convergence is 6 time faster than the default. Your change should not effect the route between R1 and R2 • Router(config-router)#timers basic 5 30 30 40 • R1(config)#interface f 0/0 • R1(config-if)#ip rip advertise 30 • R2(config)#interfaces f0/0 • R2(config-if)#ip rip advertise 30

  13. Specifying a rip version Send and receive RIP version 1 or 2 • Router(config-if)# ip rip send version 1 • Router(config-if)# ip rip send version 1 2 • Router(config-if)# iprip receive version 2 • Router(config-if)# ip rip receive version 1 2

  14. Enabling RIP Authentication RIP support two types of authentication: plain text and MD5 • Router(config)#key chain chain-name • Router(config-keychian)#key key-identifier • Router(config-keychain-key)#key-string password • Router(config-if)# ip rip authentication Key-chain chain-name • Router(config-if)# iprip authentication mode {text|md5}

  15. Enabling RIP Authentication • Router(config)#key chain chain1 • Router(config-keychian)#key 1 • Router(config-keychain-key)#key-string cisco • Router(config-if)# ip rip authentication Key-chain chain1 • Router(config-if)# ip rip authentication mode {text|md5}

  16. RIP route summarization • Disabling automatic route summarization • Router(config-router)#no auto-summary • Router(config-if)#ip summary-address rip ip- address network-mask • Verifying • Router# show ip protocols • Router# show ip rip database • Router# show ip route

  17. Routing loop • A routing loop is a situation where a packet keeps getting routed between two or more routers because of problems in the routing table. • In case of distance vector protocols, the fact that these protocols route by rumor and have a slow convergence time can cause routing loops.

  18. Preventive measures • Problem: Counting to infinity: • Solution: defining a maximum hop count • Poison route • Reverse poison • Split horizon and split horizon with poison reverse • Hold down timer

  19. Split Horizon • The split horizon rule states that routing information learned from one interface cannot be advertised back to that interface. • By default split horizon is enabled for RIP.

  20. Route Poisoning • Route poisoning uses the maximum hop counts to stop network loops. When a router looses a route, it advertises that route with a hop count of more than the maximum hop count. The receiving router now finds the destination network unreachable and advertises it ahead as such.

  21. Hold Down • This feature prevents a router from learning new information about a failed route. When a router receives an information about an unreachable route, a holddown timer is started. The router ignores all routing updates for that route until the timer expires (by default, 180 seconds in RIP).

  22. Troubleshooting Router# show ip protocols Router# Show ip rip database Router# debug ip rip Router# show ip interface brief Router# show ip route Router# show ip route 1.1.1.0

  23. Connecting RIP to WAN There are two problems when using rip • The periodic update by rip usually prevent WAN circuits from being closed • The overhead of periodic RIP transmission could seriously interrupt normal data transfer because of the quantity of the information that passes through the line every 30 second • To overcome this limitation , triggered extension to rip cause RIP to send information on the WAN connection only when there has been an update to the routing database • Router(config)#interface serial controller-number • Router(config-if)#ip rip triggered

  24. Applying offset to routing metrics • Offset list is used to influence the decision of the router. • We create an access list to specifying the route that we want to increase its metric. • Example : • R1(config)# access-list 1 permit 1.1.1.0 0.0.0.255 • R1(config-router)#offset-list 2 in 5 fastEthernet 0/0 • Add 5 to the metric of the access list

  25. Offset list example 1 • R1 reaches 11.11.11.0 on R2 in one hop count via f0/0 on R2 • Ensure that R1 reaches R2 via f0/1 not via F0/0 on R2 • We create an access-list on router R2 • R2(config)#access-list 1 permit 11.11.11.0 0.0.0.255 • We create an offset list on R2 • R2(config-router)#offset-list 1 out 6 fastEthernet 0/0 • we added 6 hop from R1 to R2 via f0/0 soooo • R1 choses another route to reach R1 with lower metric

  26. R1 newer routing table

  27. Example #2 • R3 reaches R2 in one hop count via f0/1 on R2 • Ensure that R3 reaches R2 via f0/0 not via F0/0 on R2 • We create an access-list on router R3 • R3(config)#access-list 2 permit 11.11.11.0 0.0.0.255 • We create an offset list on R3 • R3(config-router)#offset-list 2 in 5fastEthernet0/1 • we added 5 hops from R2 to R3 via f0/1 soooo • R3 choses another route to reach R1 with lower metric

  28. Change the AD • We need that R1 does not place 2.2.2.0/24 in its routing table • R1(config)#access-list 3 permit 2.2.2.0 0.0.0.255 • R1(config)# router RIP • R1(config-router)# distance 255 0.0.0.0 255.255.255.255 3

  29. RIP messages uses UDP datagrams on port 520 Implemented in Unix systems by the ‘routed’ daemon. Size of datagram limited to 512 bytes (allow advertisement of 25 routes. Command: 8 bits Request (1), reply (2) Version: 1 or 2 Family: of protocol used for TCP/IP it is 2 Network address : 32 bytes Distance: hop count from the advertising router to the destination network Response: solicited or unsolicited. RIP message format

  30. RIP message example

  31. Reference • http://www.cisco.com/c/en/us/td/docs/routers/crs/software/crs_r4-0/routing/command/reference/b_rr40crs1book/b_rr40crs1book_chapter_0111.html • https://tools.ietf.org/html/rfc1058

More Related