50 likes | 253 Views
Want to get success in 350-080 exam and looking for best and easy to understand material? With the help of our 350-080 exam questions braindumps, you can pass your certification exam very easily. We offer here only important and up-to-date 350-080 dumps question and answers and we make sure, it will be beneficial and handy for you. <br>http://www.certs4you.com/Cisco/350-080-dumps.html
E N D
Pass Cisco 350-080 - CCIE Data Center Written exam in just 24HOURS! 100% REAL EXAM QUESTIONSANSWERS Cisco 350-080 - CCIE Data CenterWritten Buy Complete Questions Answers Filefrom http://www.certs4you.com/Cisco/350-080-dumps.html 100% Exam Passing Guarantee & Money BackAssurance SampleQuestions
Question No1: A network administrator has installed an N7K-F248-25XP module into an existing chassis. The module is powered on, but the interfaces are all in VDC0. What is the reason for this? The chassis needs an EPLD upgrade to support the new module type. The default VDC cannot support F2modules. The interfaces must be allocated into a VDC for F2 modulesonly. The module has failed GOLD diagnostics, and the switch has isolated the ports to protect the integrity of thesystem. Answer: C Question No2: Which two statements about SAN port channels configured on Cisco Nexus 5000 Series switches are true? (Choose two.) The bring up protocol automatically detects and overrides anymisconfiguration. You can manually configure channel groups, or they can be automaticallycreated. Changes in configuration to the SAN port channel interface must also be made to all members of the channelgroup. The port channel protocol uses the exchange fabric parameters command to communicate across peer ports in anISL. The port channel protocol ensures that a set of ports is eligible to be part of the same SAN portchannel. Answer: B, E Question No3: Which statement about SAN port channels configured on Cisco Nexus 5000 Series Switches is true? A single SAN port channel can have both Fibre Channel and virtual Fibre Channel interfaces. SAN port channels can include up to 16interfaces. SAN port channels distribute traffic across all links in the port channel when source ID and destination ID load balancing are used. The links in SAN port channels can be connected to different sets ofswitches. The On mode of operation means ports only operate as part of a SAN port channel or remaininactive. Answer:E
Question No4: Which capabilities are not supported in DCNM devicemanager? Manage SNMPv3 security access toswitches Save and copy configuration files and softwareimages Configure VLANs and Ethernet portchannels Manage 2148T FEX, 2232PP FEX, and 2248TP FEX E. configureFCoE Answer: C Question No5: If the default VDC is configured to limit resources to a specific module type, what happens when a module that does not match the resource type isinstalled? The module is powered up, and interfaces are in an "admin down"state. The module is denied power, and a syslog message isgenerated. The module is powered up, and interfaces are allocated to VDC0. The module is powered up, and interfaces are allocated toVDC100. Answer: C Question No6: Which three flow-control port states lead to enabled link flow control? (Choosethree.) Receive port: Enabled, Transmit port:Enabled Receive port: Enabled, Transmit port:Desired Receive port: Enabled, Transmit port:Disabled Receive port: Disabled, Transmit port:Desired Receive port: Desired, Transmit port:Desired Answer: A, B,E Question No7: In a configuration with redundant supervisors, how many IP addresses are required to configure full remote access via management? Two IP addresses, one for eachsupervisor Three IP addresses, one virtual IP and one physical IP for eachsupervisor One IP address that is shared amongsupervisors None—management 0 will use the IP address from the first SVI that iscreated Answer:C
Question No8: VLAN configuration using DCNM can be completed by which two supported methods? (Choosetwo.) Copy and paste the VLAN, along with its VLAN ID, name, type, admin state, and admin status, from one device toanother. Create a single VLAN or a range ofVLANs. A VLAN is created only after choosing File > Deploy to applychanges. After a VLAN is created, it requires the state to be enabled. Modify the existing VLAN by choosing Interface > VLAN > VLANSettings. Answer: A, B Question No9: Enabling jumbo frame support on a Cisco Nexus 5500 Switch can be done through which method? Changing the default policy map from a default MTU of 1500 to9216 Using the command system jumbomtu9216 Using the command interface MTU9216 Configuring the default Ethernet system class to an MTU of 9216 with a new network QoS policymap Answer: D Question No10: Which two statements about authentication settings for DCNM-LAN are true? (Choosetwo.) If none of the authentication servers that are configured for the current authentication mode responds to an authentication request, the DCNM-LAN server falls back to localauthentication. DCNM-LAN only supportsTACACS+. Each DCNM-LAN server will have the same devicecredentials. Administering DCNM-LAN authentication settings require an authenticationlicense. DCNM-LAN server users are local to the DCNM-LANserver. Answer: A,E
Buy Complete Questions Answers Filefrom • PDF Version + Test Engine SoftwareVersion • 90 Days Free UpdatesService • Valid for AllCountries http://www.certs4you.com/Cisco/350-080-dumps.html